• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.37-43
• /
• 2003

The objective of this work is to investigate the effect of swirl, injection pressure and pilot injection on D.I. diesel combustion by using a transparent engine system. The test engine is equipped with common rail injection system to obtain high pressure and to control injection timing and duration. In this study, the combustion analysis and steady flow test were conducted to estimate the heat release rate from in-cylinder pressure. Soot distribution in diffusion flame according to swirl ratio, injection pressure and pilot injection was investigated by using LII technique. As the results, high injection pressure was found to shorten ignition delay as well as enhance peak pressure and heat release rate was greatly affected by injection timing and pilot injection. In addition, the results showed that the period of soot formation corresponded to the diffusion flame.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.1-6
• /
• 2003

The engine performance and combustion characteristics of methanol blended fuel in a multiple-point electronic control gasoline engine were discussed on the basis of experimental investigation. The effects of methanol blending fuel on combustion in cylinder were investigated under various conditions of engine cycle and blending ratio. The results showed that the engine performance was influenced by the methanol blended ratio. The results showed that the engine performance was influenced by the methanol blending ratio and the variations of operating conditions of test engine. The increase of blended fuel brought on the improvement of emission characteristics such as THC, CO, and NOx concentration. The effect of methanol blended fuel on the fuel consumption rate and the other characteristics of performance were discussed.

• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.19-31
• /
• 1993

디젤자동차는 가솔린 자동차에 비하여 연료소비효율(fuel economy)이 20-30% 정도 높고 고출력을 낼수 있어 이의 수요가 증가하고 있다. 본 고에서는 디젤자동차에서 배출되는 수많은 화학물질중에서 문제가 되고 있는 입자상물질, NOx 및 SO$_{2}$를 제거하는 기술에 대하여 살펴본다. 이러한 오염물질의 저감을 위하여는 배기가스 재순환, 분사시기의 조절, 인터쿨링 같은 연소기술의 개선과 유황분이 적고, 방향족화합물의 함량이 적은 청정연료를 사용하여 어느 수준까지는 목적을 달성할 수 있다. 1. 디젤자동차 배출허용기준. 2. 배기가스 정화기술. 2.1 트랩기술(trap technology). 2.2 재생기술(regeneration technology). 2.3 제어 및 센서기술(control and sensor technology)

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.5
• /
• pp.140-147
• /
• 2001

The solenoid valve in ABS hydraulics, modulator is a two directional on-off valve and is controlled by around 100Hz high speed pulse width modulation. When the inlet valve is switched from open state to closed state, there are braking force degration, noise and vibration due to pressure surge phenomena in the hydraulic line and wheel cylinder. In this study, identifies pressure surge phenomenon in the braking process of a ABS, and investigates the way to reduce the phenomenon. For the purpose theoretical analysis on the pressure surge in the closed state hydraulic line, characteristic curve method based on wave equation was utilized. During this analysis, we could find pressure surge characteristics change due to hydraulic line change and PWM control conditions. In conclusion, by using the results of this study for the pressure surge prediction and reduction method, we could expect braking performance enhancement in Anti-Lock Braking System.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.2
• /
• pp.235-243
• /
• 1998

For motor operation at low speeds and loads, torque pulsation by the cogging torque is often a source of vibration and control difficulty. In this paper, the magnetic field of a motor is calculated by finite element method. The periodic cogging torque is determined using Maxwell stress method and time stepping method, and then decomposed using fourier series expansion, The purpose of this paper is to characterize design parameters on the cogging torque and to design a permanent magnet motor with a cogging torque less vulnerable to vibration, without sacrificing the motor performance. The design parameters include stator slot width, permanent magnet slot width, airgap length and magnetization direction. A new design with a less populated frequency spectrum of the cogging torque is proposed after characterizing individual effect of design parameters. Magnet pole edge shaping, by gradually increasing the cogging torque with reduced higher harmonics.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.5
• /
• pp.90-99
• /
• 1996

To keep up with the regulation of OBD II(on board diagnostics II), many detection methods for engine misfire have been developed. Among them, the method of using the crankshaft speed fluctuation is the most noticeable in the point of view of lower cost and easier installation than any others. On the basis of the results obtained from the previous engine-dynamometer test, the integrating torque index (ITI) has been introduced. In this research, the instrumental and the interfacing systems to engine control unit(ECU) are developed for the vehicle test. Therefore, the vehicle and chassis-dynamometer test can be carried out in addition to the rough road test. From this test, the previousproposed method proved that it can be applied to the real vehicle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.108-117
• /
• 2003

Development of advanced restraint system challenges both restraint and automobile manufacturers to come up with proper airbag design to reduce occupant out-of-position related injury. The important component of the advanced restraint system is the multi stage inflator. The multi stage inflator can independently control two or more airbag inflation stages to maximize occupant protection. The objective of this research is to develop relationship between airbag inflation characteristics, the occupant positions and the airbag design variables. The tests are conducted using five kinds of inflators, two kinds of airbag cushion folding methods and two kinds of tear lines. In the case of inflator, the out-of-position tests are performed with a traditional inflator, a depowered inflator and a dual stage inflator. And the efficiency and injury mechanism are evaluated by analyzing the injury pulses and values. Using this relationship, airbag design guideline is established for airbag aggressivity thresholds and the risk of injury is identified according to occupant positions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.1
• /
• pp.20-32
• /
• 1995

Springs for vehicle suspension control the vibration of a car and influence on the ridability, safety, and life of a car. In the paper, the computer aided design program has been developed, which design the leaf spring shape from the given specifications using basic theory and the expert's knowledge, and the design results are checked by the analysis theory in order to increase the accuracy, and feed back to the design input. For the purpose of easy use, this program consists of pull-down menu and interactive input mode. To prove the effectiveness of this program. two springs, of which one is symmetric, other asymmetric, are designed and analyzed, and the outputs are compared to the experiments. Considering the tolerance of the given specifications, the results are good.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.3
• /
• pp.9-18
• /
• 1995

The substitution of conventional fuel oil by alternative fuels is of immense interest due to liquid oil shortage and requirements of emission control standard. Among the alternative fuels, natural gas may be the most rational fuel, because of its widespread resource and clean est burning. Meanwhile, engine simulation is of great importance in engine development. Hence a zero-dimensional combustion model was developed for dual-fuel system. Natural gas was injected directly into the cylinder and small amount of distillate was used to provide the ignition kernel for natural gas burning. The intake air and exhaust gas flow was modeled by filling and emptying method. Although the single zone approach has an inherent limitation, the model showed promise as a predictive tool for engine performance. Its simulation was also made to see how the engine performance was influenced by the fuel injection timings and amount of each fuel.

• Journal of Korea Society of Industrial Information Systems
• /
• v.4 no.3
• /
• pp.71-78
• /
• 1999

This paper presents an integrated and automated inspection system using image processing technology for the automotive engine assembly process. The system make it possible for the inspected data to be entered directly from the machine vision into the statistical process control system. Such direct entry enables the prompt preparation of corrective actions against process problems. An IVP-150 machine vision board is installed within the PC for image processing, and a template matching technology is implemented to precisely verify quality factors. The developed system showed robustness to the problems of noise, distortion, and orientation.