• Proceedings of the Safety Management and Science Conference
• /
• 2006.04a
• /
• pp.355-362
• /
• 2006

This paper is to introduce guidelines for automotive and food quality management system. International standards such as ISO/TS 16949 and ISO 15161 are considered. This study is to discuss particular requirements for the application of ISO 9001 : 2000 for automotive production and relevant service part organization , and guidelines on the application of ISO 9001 : 2000 for the food and drink industry.

• Journal of the korean Society of Automotive Engineers
• /
• v.23 no.4
• /
• pp.32-35
• /
• 2001

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.6
• /
• pp.117-125
• /
• 2012

This paper describes a model-based software development methodology for AUTOSAR-ready light software architecture(AUTOSAR-Lite). The proposed methodology briefly represents an application software modeling technique using Matlab/Simulink. Using the proposed technique, application software architecture elements (e.g. software components, runnables, and interfaces) and functional behaviors can be designed in a single modeling environment. From the designed model, the codes of application software is automatically generated using Real-Time Workshop Embedded Coder. The generated application software is easily integrated with hand-coded basic software using the proposed method. In order to evaluate the proposed methodology, a diesel engine management system for a passenger car was employed as a case study. Based on the methodology, 8 atomic software components and 52 runnables are successfully developed, and they are evaluated by engine experiments. From this case study, AUTOSAR compatible model-based application software was successfully developed, and the effectiveness of the proposed methodology was evaluated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.54-59
• /
• 2006

An analytical solution for deflection-load characteristics of a conical disk spring used especially in the automotive manual transmission clutch applications is proposed in order to take into account the effects of friction and large deformation. The conical disk spring, or the diaphragm spring, has a hinge support, an application point of release load at the tip of the fingers and an application point of clamp load near but inside the outer perimeter of the conical disk spring. The friction coefficient is assumed to be a constant regardless of the speed of deflection and the magnitude of loads. Comparison with experimental shows a good agreement with the analytical prediction. Also, the sensitivity of the clamp load due to variations in the geometrical parameters of the conical disk spring is calculated and discussed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.1
• /
• pp.68-77
• /
• 2013

This paper presents AUTOSAR-ready light software architecture (AUTOSAR-Lite), which is a light weighted version of the AUTOSAR, for automotive embedded control systems. The proposed AUTOSAR-Lite reduces overhead problems caused by the excessive standard specifications of AUTOSAR. Concurrently, AUTOSAR-Lite keeps advantages of AUTOSAR such as a scalability, re-usability, reliability, and transferability. The fundamental design of AUTOSAR-Lite is originated from the AUTOSAR standard. AUTOSAR-Lite is composed of three layers such as an application software, runtime environment, and basic software layer. The application software layer adopts component-based design methodology as AUTOSAR. The runtime environment layer integrates interfaces between application and basic software layers. In case of the basic software layer, restrictions of the module configurations and interfaces of basic software are minimized. In order to validate the feasibility of AUTOSAR-Lite, a software design result based on AUTOSAR-Lite software architecture for electronic throttle control (ETC) system is suggested.

• Journal of the korean Society of Automotive Engineers
• /
• v.31 no.3
• /
• pp.70-75
• /
• 2009

• Journal of the korean Society of Automotive Engineers
• /
• v.31 no.4
• /
• pp.66-71
• /
• 2009

• Proceedings of the KWS Conference
• /
• 2006.10a
• /
• pp.77-79
• /
• 2006

While RSW(Resistance Spot Welding) have been the most successful sheet metal joining process in automotive industry, there are certain qualify issues due to the control system and its application process. Recent materials and coatings make the process more complicated resulting in new challenges for quality welds. In this research, an intelligent RSW system with adaptive control algorithm is introduced to overcome typical RSW issues and its applications to automotive body assembly are presented.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.6
• /
• pp.1-9
• /
• 2008

The current test methods are insufficient to evaluate and ensure the safety and reliability of vehicle system for all possible dynamic situation including the worst case such as rollover, spin-out and so on. Although the known NHTSA J-turn and Fish-hook steering maneuvers are applied for the vehicle performance assessment, they aren't enough to estimate other possible worst case scenarios. Therefore, it is crucial for us to verify the various worst cases including the existing severe steering maneuvers. This paper includes the procedure to search for other useful worst case based upon the existing worst case scenarios mentioned above and its application in simulation basis. The only human steering angle is selected as a design parameter here and optimized to maximize the index function to be expressed in terms of either roll angle or yaw rate. The obtained scenarios were enough to generate the worst case to meet NHTSA worst case definition (ex.2-inch wheel lift). Additionally, as an application, the worst case steering maneuver is acquired for the vehicle to operate with a simple ESP system. It has been concluded that the new procedure in this paper is adequate to create other feasible worst case scenarios for a vehicle system both with an intelligent safety control system and without it.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.6
• /
• pp.90-96
• /
• 2011

In this study, the characteristic of fractured portion and shape on solder joints were investigated according to the thermal shock test for Automotive Application Component using Sn-3.0Ag-0.5Cu solder, which has a outstanding property as Lead-free solder. The value of pull and shear strength was decreased in principle after 432 cycles thermal shock test. In addition, fracture mode was verified by using EDS and SEM to observe fractured shape on the solder joints before and after thermal shock. In before thermal shock test, the fracture mode revealed typically solder layer's fracture mode. In after thermal shock test, we identified multiple fracture mode of the ductile and brittle fracture. Even though same composition of solder was used to experimental for estimating. the fracture mode varied on the fracture portion's height and the directional angles of shear strength. In conclusion, we identified that mechanical strength was affected on the solder layer's fracture mode.