• Proceedings of the KIEE Conference
• /
• 2004.07d
• /
• pp.2397-2399
• /
• 2004

This paper deals with the messages scheduling of a CAN (Controller Area Network), based on the distributed control scheme to integrate actuators and sensors in a humanoid robot. In order to supply the distributed processing for a humanoid robot, each control unit should have the efficient control method, fast calculation and valid data exchange. The preliminary study has concluded that the performance of CAN is better and easier to implement than other network such as FIP (Factory Instrumentation Protocol), VAN (Vehicle Area Network), etc. Since humanoid robot has to treat the significant control signals from many actuators and sensors, the communication time limitation could be critical according to the transmission speed and data length of CAN specification. In this paper, the CAN message scheduling in humanoid robot was suggested under the presence of Jitter in the message group, the existence of high load of messages over the network and the presence of transmission errors. In addition, the response time under the worst case is compared with the simulation by using the simulation algorithm. As a result, the suggested messages scheduling can guarantee our CAN limitation, and utilized to generate the walking patterns for the humanoid.

• Transactions on Control, Automation and Systems Engineering
• /
• v.3 no.4
• /
• pp.223-228
• /
• 2001

We have been developed an intelligent mobile robot with an artificial olfactory function to recognize odours and to track odour source location. This mobile robot also has ben installed an engine for speech recognition and synthesis and is controlled by wireless communication. An artificial olfactory system based on array of 7 gas sensors has been installed in the mobile robot for odour recognition, and 11 gas sensors also are located in the obttom of robot to track odour sources. 3 optical sensors are also in cluded in the intelligent mobile robot, which is driven by 2 D. C. motors, for clash avoidance in a way of direction toward an odour source. Throughout the experimental trails, it is confirmed that the intelligent mobile robot is capable of not only the odour recognition using artificial neural network algorithm, but also the tracking odour source using the step-by-step approach method. The preliminary results are promising that intelligent mobile robot, which has been developed, is applicable to service robot system for environmental monitoring, localization of odour source, odour tracking of hazardous areas etc.

• International Journal of Control, Automation, and Systems
• /
• v.1 no.2
• /
• pp.243-251
• /
• 2003

In this paper, a new model for mobile soccer robot, a type of linear system, is presented. A controller, consisting of two loops the one of which is the inner state feedback loop designed for stability and plant be well conditioned and the outer loop is a well-known PI controller designed for tracking the reference input, is suggested. Because the plant, the soccer robot, is parameter dependent, it requires the controller to be insensitive to the parameter variation. To achieve this objective, the pole-sensitivity as a pole-variation with respect to the parameter variation is defined and design algorithms for state-feedback controllers are suggested, consisting of two matrices one of which is for general pole-placement and other for parameter insensitive. This paper shows that the PI controller is equivalent to the state feedback and the cost function for reference tracking is equivalent to the LQ cost. By using these properties, we suggest a tuning procedure for the PI controller. We that the control algorithm in this paper, based on the linear system theory, is well work by simulation, and the LPD system modeling and control are more easy treatment for soccer robot.

• International Journal of Control, Automation, and Systems
• /
• v.1 no.2
• /
• pp.210-214
• /
• 2003

This paper presents a residence time distribution (RTD) measurement method using a radioisotope tracer and the estimation method of RTD model parameters to analyze a submerged bio-reactor. The mathematical RTD models have been investigated to represent the flow behavior and the existence of stagnant regions in the reactor. Knowing the parameters of the RTD model is important for understanding the mixing characteristics of a reactor The radioisotope tracer experiment was carried out by injecting a radioisotope tracer as a pulse into the inlet of the reactor and recording the change of its concentration at the outlet of the reactor to obtain the experimental RTD response. The parameter estimation was performed by the Levenberg-Marquardt optimization algorithm. The proposed scheme allowed the parameter estimation of RTD model suggested by Adler-Hovorka with very low deviations. The estimation procedure is shown to lead to accurate estimation of the RTD parameters and to a good agreement between experimental and simulated response.

• Journal of Mechanical Science and Technology
• /
• v.14 no.4
• /
• pp.380-392
• /
• 2000

A typical production-distribution system consist of three main echelons representing the retailer, distributors, and a factory each with an on-site warehouse. The system is sufficiently general and realistic to represent many industrial situations. However, decision functions and parameters have been selected to apply particularly to the production and distribution of consumer durables. The flows included in the model are materials, orders, and those information flows needed to support the material and order-rate decisions. In this work, a realistic production-distribution system has been used as a basic model, which consists of three sectors: retailer, distributor, and factory. That system is a nonlinear 25th-order continuous system interconnected between the echelons. Using a modern control algorithm, a typical multi-echelon production-distribution system using a dynamic controller is numerically simulated in the nominal plant and in the perturbed plant when the piecewise constant manufacturing decision is limited by a factory manufacturing upper-limit due to capital equipment, manpower, and factory lotsize.

• Smart Structures and Systems
• /
• v.22 no.2
• /
• pp.167-174
• /
• 2018

Digital input and output modules are widely used to connect digital sensors and actuators to automation systems. Digital I/O modules provide flexible connectivity extension to numerous sensors and actuators and protect systems from high voltages and currents by isolation. Components in digital I/O modules are inevitably affected by operating and environmental conditions, such as high voltage, high current, high temperature, and temperature cycling. Because digital I/O modules transfer signals or isolate the systems from unexpected voltage and current transients, their failures may result in signal transmission failures and damages to sensitive circuitry leading to system malfunction and system shutdown. In this study, the lifetime of optocouplers, one of the critical components in digital I/O modules, was predicted using Bayesian tracking approaches. Accelerated degradation tests were conducted for collecting the critical performance parameter of optocouplers, current transfer ratio (CTR), during their lifetime. Bayesian tracking approaches, including extended Kalman filter and particle filter, were applied to predict the failure. The performance of each prognostic algorithm was then compared using accuracy and robustness-based performance metrics.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.5
• /
• pp.423-433
• /
• 2016

In this paper, we consider the cybersecurity issue of ship information system (SIS) from a new perspective which is called opacity. For a SIS, its confidential information (named as "secret") may be leaked through the working behaviors of each Distributed Control Unit (DCU) from an outside observer called an "intruder" which is able to determine ship's mission state by detecting the source of each data flow from the corresponding DCUs in SIS. Therefore we proposed a dual layer mechanism to enforce opacity by activating non-essential DCU during secret mission. This mechanism is calculated by two types of insertion functions: Safety-assured insertion function ($f_{IS}$) and Admissibility-assured insertion function ($f_{IA}$). Due to different objectives, $f_{IS}$ is designed to confuse intruder by constructing a non-secret behaviors from a unsafe one, and the division of $f_{IA}$ is to polish the modified output behaviors back to normal. We define the property of "$I_2$-Enforceability" that dual layer insertion functions has the ability to enforce opacity. By a given mission map of SIS and the marked secret missions, we propose an algorithm to select $f_{IS}$ and compute its matchable $f_{IA}$ and then the DCUs which should be activated to release non-essential data flow in each step is calculable.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.3
• /
• pp.158-168
• /
• 2001

Die design of die casting is composed of selection of cast alloy, design of die casting product, runner design and gate design, etc. In reality, however, die design of die casting has been performed by trial and error method, which cause economic and financial loss. Nowadays, several FEM(finite element method) and FDM(finite difference method) codes have been developed to analyze process of die casting, but this is just confined to an offer of limited information for die design of die casting. In this study, die design system for gate of die casting process has been developed to present algorithm for automation of die design, especially runner-gate system. In addition, specific rules for runner-gate system have been presented to avoid too many trials and errors with expensive equipment. It is possible for engineers to make automatic and efficient die design of die casting and it will result in reduction of expense and time to be required.

• Journal of Welding and Joining
• /
• v.29 no.3
• /
• pp.64-69
• /
• 2011

Since welding process for most pipelines with large diameter has been carried out by the manual process, automation of the welding process is necessary for the sake of consistent weld quality and improvement in productivity. Therefore the development of the optimized algorithm to decide the welding condition is an effective technique to prove the feasibility of interface standards and intelligent control technology to increase productivity and reduce the cost of system integration. In this study, the pipe welding experiment has been carried out using plused GMA welding process to select optimal welding condition. And necessary information in root-pass welding has been obtained by applying in the pipeline using the selected welding conditions through the welding experiment.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.1
• /
• pp.112-117
• /
• 2017

The arc, generated by Tungsten Inert Gas(TIG) welding, is stable and provides excellent quality of the weld. Since automation is difficult, a lot of work is performed by hand. In addition, to obtain the uniform weld quality is difficult when using a base metal having a nonuniform welding line, or when welding inside a pipe. Generally, TIG welding power has the characteristic of constant-current. The welding voltage is changed in proportion to the arc length. Hence, the automatic voltage control equipment should be applied at the TIG welding system. The automatic voltage control equipment has been designed using LabVIEW software. It consists of a manufactured voltage divider circuit, and jig for moving the torch. The voltage measurements and driving of the motor were performed through the algorithm implementation in LabVIEW. Welding was conducted while increasing the arc length. In this process, it was confirmed that the automatic voltage control equipment kept the arc length constant.