• 한국재료학회지
• /
• 제30권1호
• /
• pp.44-49
• /
• 2020

The effect of intercritical annealing temperature on the microstructure and mechanical properties of Fe-9Mn-0.2C-3Al-0.5Si medium manganese steels containing Cu and Ni is investigated in this study. Six kinds of medium manganese steels are fabricated by varying the chemical composition and intercritical annealing temperature. Hardness and tensile tests are performed to examine the correlation of microstructure and mechanical properties for the intercritical annealed medium manganese steels containing Cu and Ni. The microstructures of all the steels are composed mostly of lath ferrite, reverted austenite and cementite, regardless of annealing temperature. The room-temperature tensile test results show that the yield and tensile strengths decrease with increasing intercritical annealing temperature due to higher volume fraction and larger thickness of reverted austenite. On the other hand, total and uniform elongations, and strain hardening exponent increase due to higher dislocation density because transformation-induced plasticity is promoted with increasing annealing temperature by reduction in reverted austenite stability.

• 한국산업안전학회:학술대회논문집
• /
• 한국안전학회 2003년도 추계 학술논문발표회 논문집
• /
• pp.107-112
• /
• 2003

형상기억합금(shape memory alloy; SMA)은 소성가공을 통하여 원하는 형태로 변형시킨 이후에도(현재로서는 최대 10%미만의 변형) 일정조건의 열을 가하면 원래의 형상으로 복원되는 합금을 말한다. 형상기억효과는 고상(solid state)에서의 금속조직이 오스테나이트(austenite: 이하 A 또는 B2상)로부터 마르텐사이트(martensite: 이하 M 또는 B19'상)로, 다시 역으로 마르텐사이트에서 오스테나이트로의 변태에 기인되는 것으로 밝혀지고 있으며 이러한 변태는 온도유기변태(temperature induced transformation)와 응력유기변태(stress induced transformation)로 분류할 수 있다.(중략)

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.332-335
• /
• 2005

A model is developed to quantitatively analyze the dilatometry curve of carbon steel for the evaluation of phase fraction during transformation. The effect of anisotropic volume change due to transformation mismatch plasticity as well as carbon enrichment in austenite during the transformation is considered in the developed model. The developed model is applied for the analysis of dilatometry curves of carbon steels. The result shows that considering the anisotropic dilatation is very essential to quantitatively evaluate the phase fraction from the dilatation curve.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.318-321
• /
• 2009

Transformation plasticity is that when a phase transformation of ferrous or non-ferrous alloys progresses even under an extremely small applied stress compared with a yield stress of the material, a permanent deformation occurs. One of widely accepted description for the transformation was proposed by Greenwood and Johnson [1]. Their description is based on an assumption that a weaker phase of an ideal plastic material could deform plastically to accommodate the externally applied stress and the internal stress caused by the volumetric change accompanying the phase transformation. In this study, an implicit finite element model was developed to simulate the deformation behavior of a low carbon steel during phase transformation. The finite element model was coupled with a phase field model, which could simulate the kinetics for ferrite to austenite transformation of the steel. The thermo-elasto-plastic constitutive equation for each phase was adopted to confirm the weaker phase yielding, which was proposed by Greenwood and Johnson [1]. From the simulation, the origin of the transformation plasticity was quantitatively discussed comparing with the other descriptions of it.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년도 춘계 학술대회 개요집
• /
• pp.127-129
• /
• 2006

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년도 춘계 학술대회 개요집
• /
• pp.115-117
• /
• 2006

• 대한치과교정학회지
• /
• 제40권1호
• /
• pp.40-49
• /
• 2010

본 연구의 목적은 martensitic (M-NiTi), austenitic (A-NiTi) 및 thermodynamic nickel-titanium wire (T-NiTi)의 물리적 특징과 상전이 정도를 평가하는 것이다. 재료는 $0.016\;{\times}\;0.022$ inch의 M-NiTi (Nitinol Classic, NC), A-NiTi (Optimalloy, OPTI)와 T-NiTi (Neo-Sentalloy, NEO)이었으며, differential scanning calorimetry (DSC), 3점굽힘실험, X-ray diffraction (XRD), 미세구조 분석을 시행하였으며, ANOVA test로 통계처리하였다. DSC분석 결과 OPTI와 NEO는 heating curve에서 2개의 peak, cooling curve에서 1개의 peak를 보였고, NC는 heating과 cooling curve에서 1개의 넓고 약한 peak를 보였다. Austenite finishing ($A_f$) 온도는 OPTI $19.7^{\circ}C$, NEO $24.6^{\circ}C$, NC $52.4^{\circ}C$였다. 3점굽힘실험 결과 NC, OPTI, NEO 모두 residual deflection을 보였으며, NC와 OPTI의 load range가 NEO보다 컸다. XRD와 미세구조 분석결과 OPTI와 NEO는 Martensite finishing ($M_f$)에서 martensite와 austenite가 섞여 있음이 관찰되었다. NEO와 OPTI는 NC보다 개선된 물리적 특징과 상전이 행태를 보였다. NiTi 호선의 물리적, 온도에 따른 행태는 예상되었던 상전이 정도에 의해 완벽하게 설명되지 않았으며, 그 이유는 복잡한 martensite variants의 존재와 열과 stress에 의해 유도된 독립적인 상전이에 기인한다고 생각된다.

• 열처리공학회지
• /
• 제4권1호
• /
• pp.1-12
• /
• 1991

This study has been performed to find out the effect of austenitizing temperature, austempering temperature and its holding time, and tempering cycle on the mechanical properties such as impact resistance, hardness etc. of AISI $M_2$ Mo series high speed tool steel austempered or tempered after austempering treatment. The results obtained from the experiment are as follows ; (1) Optical micrograph has revealed that the transformation rate of bainite is delayed as the austenitizing temperature increases and that bainite is most apparently transformed at an austempering temperature of $290^{\circ}C$. (2) The amount of retained austenite during austempering has been analysed to be increased by the X-ray diffraction technique as the transformation product of bainite is increased. It has also been shown that the longer the holding time of austempering, the more the transformation quantity of bainite is formed, exhibiting, however, that the rate of bainitic transformation is considerably retarded after a certain period of holding time elapses. (3) Hardness measurement has shown that hardness values obtained after austempering increase with decreasing the amount of retained austenite. (4) The austempering and then tempering cycle has been formed to give hardness values which are more greatly improved as austenitizing temperature is increased. (5) The mechanical property of the specimen primary-tempered for 1 hour at $550^{\circ}C$ after austempering for 2 hours at $290^{\circ}C$ from the austenitizing temperature range of $1180^{\circ}C$ to $1210^{\circ}C$ have been estimated to be good values.

• 열처리공학회지
• /
• 제11권2호
• /
• pp.75-81
• /
• 1998

The effect of thermomechanical treatment on thermal expantion and melting point of Fe-30%Ni-0.35%C alloy was investigated. The dimention changes of the ausformed martensite and the marformed martensite were decreased with increasing deformation degree in the range of $25{\sim}350^{\circ}C$ prior to reverse transformation but became larger in the range of $500{\sim}800^{\circ}C$ after the reverse transformation. The dimension change and the thermal expansion coefficient were reduced in the order of the deformed austenite, the marformed martensite and the ausformed martensite in the range of $25{\sim}800^{\circ}C$. Therefore, the ausforming treatment is more effective than the marforming treatment in improving the heat-resistance. The melting points of the deformed austenite, the ausformed martensite and the marformed martensite were lowered as either the heating rate or the degree of deformation was increased.

• 열처리공학회지
• /
• 제11권3호
• /
• pp.216-226
• /
• 1998

Heat treatment conditions and the formation of microstructures were studied for improving the transformation-induced plasticity(TRIP) effect of retained austenite and mechanical properties of Fe-0.2%C-1.5%Si-1.5%Mn sheet steel. An excellent combination of elongation about 30% and high strength over 760MPa was achieved by processing of intercritical annealing and isothermal holding Intercritical annealing the sheet steel produced fine particles($1{\sim}2{\mu}m$) of retained austenite which were stabilized due to C enrichment by subsequent holding in bainite transformation range. Heat treatment conditions were depended on the shape and distribution of second phases as well as the volume fraction and stability of retained austenrte. In this work, the heat treatment condition of optimal strength-elongation balance was obtained by holding the steel at $400^{\circ}C$ for 200sec, after intercritical annealing at $790^{\circ}C$ for 300sec.