• Journal of Korean Society for Atmospheric Environment
• /
• 제33권4호
• /
• pp.377-392
• /
• 2017

A set of BFM (Brute Force Method) simulations with the CMAQ (Community Multiscale Air Quality) model were conducted in order to estimate self-contributions and conversion rates of PPM (Primary $PM_{2.5}$), $NO_x$, $SO_2$, $NH_3$, and VOC emissions to $PM_{2.5}$ concentrations over the SMA (Seoul Metropolitan Area). CAPSS (Clean Air Policy Support System) 2013 EI (emissions inventory) from the NIER (National Institute of Environmental Research) was used for the base and sensitivity simulations. SCCs (Source Classification Codes) in the EI were utilized to group the emissions into area, mobile, and point source categories. PPM and $PM_{2.5}$ precursor emissions from each source category were reduced by 50%. In turn, air quality was simulated with CMAQ during January, April, July, and October in 2014 for the BFM runs. In this study, seasonal variations of SMA $PM_{2.5}$ self-sensitivities to PPM, $SO_2$, and $NH_3$ emissions can be observed even when the seasonal emission rates are almost identical. For example, when the mobile PPM emissions from the SMA were 634 TPM (Tons Per Month) and 603 TPM in January and July, self-contributions of the emissions to monthly mean $PM_{2.5}$ were $2.7{\mu}g/m^3$ and $1.3{\mu}g/m^3$ for the months, respectively. Similarly, while $NH_3$ emissions from area sources were 4,169 TPM and 3,951 TPM in January and July, the self-contributions to monthly mean $PM_{2.5}$ for the months were $2.0{\mu}g/m^3$ and $4.4{\mu}g/m^3$, respectively. Meanwhile, emission-to-$PM_{2.5}$ conversion rates of precursors vary among source categories. For instance, the annual mean conversion rates of the SMA mobile, area, and point sources were 19.3, 10.8, and $6.6{\mu}g/m^3/10^6TPY$ for $SO_2$ emissions while those rates for PPM emissions were 268.6, 207.7, and 181.5 (${\mu}g/m^3/10^6TPY$), respectively, over the region. The results demonstrate that SMA $PM_{2.5}$ responses to the same amount of reduction in precursor emissions differ for source categories and in time (e.g. seasons), which is important when the cost-benefit analysis is conducted during air quality improvement planning. On the other hand, annual mean $PM_{2.5}$ sensitivities to the SMA $NO_x$ emissions remains still negative even after a 50% reduction in emission category which implies that more aggressive $NO_x$ reductions are required for the SMA to overcome '$NO_x$ disbenefit' under the base condition.

• Journal of Environmental Impact Assessment
• /
• 제24권2호
• /
• pp.134-153
• /
• 2015

When making urban planning, it is important to understand climate effect caused by urban structural changes. Seoul city applies UPIS(Urban Plan Information System) which provides information on urban planning scenario. Technology for analyzing climate effect resulted from urban planning needs to developed by linking urban planning scenario provided by UPIS and climate analysis model, CAS(Climate Analysis Seoul). CAS develops for analyzing urban climate conditions to provide realistic information considering local air temperature and wind flows. Quantitative analyses conducted by CAS for the production, transportation, and stagnation of cold air, wind flow and thermal conditions by incorporating GIS analysis on land cover and elevation and meteorological analysis from MetPhoMod(Meteorology and atmospheric Photochemistry Meso-scale model). In order to reflect land cover and elevation of the latest information, CAS used to highly accurate raster data (1m) sourced from LiDAR survey and KOMPSAT-2(KOrea Multi-Purpose SATellite) satellite image(4m). For more realistic representation of land surface characteristic, DSM(Digital Surface Model) and DTM(Digital Terrain Model) data used as an input data for CFD(Computational Fluid Dynamics) model. Eight inflow directions considered to investigate the change of flow pattern, wind speed according to reconstruction and change of thermal environment by connecting green area formation. Also, MetPhoMod in CAS data used to consider realistic weather condition. The result show that wind corridors change due to reconstruction. As a whole surface temperature around target area decreases due to connecting green area formation. CFD model coupled with CAS is possible to evaluate the wind corridor and heat environment before/after reconstruction and connecting green area formation. In This study, analysis of climate impact before and after created the green area, which is part of 'Connecting green network across the north and south in Seoul' plan, one of the '2020 Seoul master plan'.

• Journal of Korean Society of Forest Science
• /
• 제94권6호
• /
• pp.370-376
• /
• 2005

Sarcodon aspratus is well known as a natural edible mushroom and a symbiotic mycorrhizal fungus with oaks. This study was conducted to clarify the effects of environmental conditions on the fruiting of S. aspratus on the hillslope of Wolak Mt., Jecheon city, Chungbuk, South Korea. Soil moisture and soil temperature in S. aspratus colony were measured hourly and compared with those in the non-colony soil. The mean soil moisture during the mushroom development was 14.3% in the colony soil and 16.4% in the non-colony soil. The S. aspratus colony soils showed 2.1% less soil moisture. The mean soil temperature was $16.8^{\circ}C$ in the colony soil and $16.5^{\circ}C$ in the non-colony soil. The S. asprauts colony soils showed slightly higher temperature. It is considered that more soil water was consumed and more energy was emitted during the mycelial elongation and the mushroom development. The development of S. aspratus seems similar to that of T. matsutake which is known to be considerably affected by soil moisture, daily maximum air temperature, daily minimum air temperature and daily minimum soil temperature. The season of S. aspratus development ranges from the end of August to the beginning of October. And Ellino phenomenon and its unusual change in the weather seems to affect primodia and fruiting body development. Especially if daily minimum soil temperature continues to become higher than $20^{\circ}C$, the damage of primodia and its fruiting body was frequently observed in the field plots during the last few years recently.

• Korean Chemical Engineering Research
• /
• 제50권4호
• /
• pp.690-695
• /
• 2012

Gas hydrate is an inclusion compound consisting of water and low molecular weight gases, which are incorporated into the lattice structure of water. Owing to its promising aspect to application technologies, gas hydrate has been widely studied recently, especially $CO_2$ hydrate for the CCS (Carbon Capture and Storage) issue. The key point of $CO_2$ hydrate technology for the CCS is how to produce gas hydrate in an efficient and economic way. In this study, we have tried to study the characteristic of gas hydrate formation using micro-sized ice through an ultrasonic nozzle which generate 2.4 MHz frequency wave. $CO_2$ as a carrier gas brings micro-sized mist into low-temperature reactor, where the mist and carrier gas forms $CO_2$ hydrate under $-55^{\circ}C$ and atmospheric pressure condition and some part of the mist also remains unreacted micro-sized ice. Formed gas hydrate was average 10.7 of diameter at average. The starting ice particle was set to constant pressure to form $CO_2$ hydrate and the consumed amount of $CO_2$ gas was simultaneously measured to calculate the conversion of ice into gas hydrate. Results showed that the gas hydrate formation was highly suitable because of its extremely high gas-solid contact area, and the formation rate was also very high. Self-preservation effect of $CO_2$ hydrate was confirmed by the measurement of $CO_2$ hydrate powder at normal and at pressed state, which resulted that this kind of gas storage and transport could be feasible using $CO_2$ hydrate formation.

• Applied Chemistry for Engineering
• /
• 제26권3호
• /
• pp.311-318
• /
• 2015

This work investigated the plasma treatment of aqueous bisphenol A (BPA) solution and mineralization pathways. For the effective contact between plasmatic gas and aqueous BPA solution, the plasma was created inside a porous ceramic tube, which was uniformly dispersed into the aqueous solution through micro-pores of the ceramic tube. Effects of the gas flow rate, applied voltage and treatment time on the decomposition of BPA were examined, and analyses using ultraviolet (UV) spectroscopy, ion chromatography and gas chromatography-mass spectrometry were also performed to elucidate mineralization mechanisms. The appropriate gas flow rate was around $1.0L\;min^{-1}$; when the gas flow rate was too high or too low, the BPA decomposition performance at a given electric power decreased. The increase in the voltage improves the BPA decomposition due to the increased electric power, but the energy required to remove BPA was similar, regardless of the voltage. Under the condition of $1.0L\;min^{-1}$ and 20.8 kV, BPA at an initial concentration of $10L\;min^{-1}$ (volume : 1 L) was successfully treated within 30 min. The intermediates produced by the attack of ozone and hydroxyl radicals on BPA were further oxidized to stable compounds such as acetate, formate and oxalate.

• Journal of the Korean earth science society
• /
• 제35권3호
• /
• pp.168-179
• /
• 2014

The purpose of this study focuses on the prediction time and location of turning-point of typhoon tracks using the water vapor images of Communication, Ocean and Meteorological Satellite (COMS) which has a very short observation interval. It targets a more accurate prediction of turning-point of typhoon tracks through the relationship between dry slot and northern/southern oscillations of jet stream. Jet stream moves by the position of jet streak and the ${\upsilon}$-component velocity of geostrophic wind. If the ${\upsilon}$-component of geostrophic wind gets stronger toward south, jet stream develops into a circular jet. In that condition, dry slot in satellite water vapor imagery extends toward south, and typhoon track turns as the distance of curved moisture band (CMB) gets narrowed down. If the interval of CMB is below $15^{\circ}$ of latitude, the typhoon track is turning toward north or northeast within 24 hours. As a result, typhoon track showed that when dry slot position was located less than $32^{\circ}N$, typhoon turned its track at $20-23^{\circ}N$ ($1^{th}$ Kong-Rey 2007 and $17^{th}$ Jelawt at 2012), and when in $35^{\circ}N$ above, it turned at $27^{\circ}N$ ($4^{th}$ Man-yi 2007).

• Korean Chemical Engineering Research
• /
• 제51권2호
• /
• pp.214-220
• /
• 2013

Hydrophobic coating on a silicate-based yellow phosphor ($Sr_2SiO_4:Eu^{2+}$) was carried out by using hexamethyldisiloxane (HMDSO) precursor in an atmospheric pressure dielectric barrier discharge plasma reactor, eventually to improve the long-term stability and reliability of the phosphor. The phosphor powder samples were characterized by a scanning electron microscope (SEM), a transmission electron microscope (TEM), a fluorescence spectrophotometer and a contact angle analyzer. After the coating was prepared, the contact angle of the phosphor powder increased to $133.0^{\circ}$ for water and to $140.5^{\circ}$ for glycerol, indicating that a hydrophobic layer was formed on its surface. The phosphor coated with HMDSO exhibited photoluminescence enhancement up to 7.8%. The SEM and TEM images of the phosphor powder revealed that the plasma coating led to a morphological change from grain-like structure to smooth surface with 31~46 nm thick hydrophobic layer. The light emitting diode (3528 1 chip LED) fabricated with the coated phosphor showed a substantial enhancement in the reliability under a special test condition at $85^{\circ}C$ and 85% relative humidity for 1,000 h (85/85 testing). The plasma-mediated method proposed in this work may be applicable to the formation of 3-dimensional coating layer on irregular-shaped phosphor powder, thereby improving the reliability.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• 제25권2호
• /
• pp.44-53
• /
• 1989

In order to grasp the characteristics of a fishing ground at yeosu bay, the fluctuation in condition of the coast and that in catch by pound nets in the coast were investigated respectively. The results obtained are summarized as follows: 1. The water temperature in spring and summer was higher at the coast side than off shore, but in autumn and winter took the reverse. 2. The salinity was higher in spring and winter than in summer and autumn. A lower salinity zone was found at the Dolsan Do coast and higher ones were made off shore. 3. A eddy current was found at the Dolsan Do coast and a thermocline were made at the depth of 30 to 40 m in summer. But in autumn and winter the water became homogeneous. 4. The annual catch by the pound net was highest in 1984 and then decreased gradually. The monthly catch was highest in June and then decreased gradually. 5. The catches seemed to increase with the sea water temperature and salinity, and great catch was shown in 21$^{\circ}C$ to 27$^{\circ}C$ and 33.80% to 34.00%. 6. The component rate of fishes was 28.4% in spanish mackerel, 17.9% in anchovy, 19.5% in horse mackerel, 21.0% in sardine, 7.2% in hairtail, and 1% in common mackerel. 7. The fishes appeared continuously on way of fishing operation were spanish mackerel, hairtail, Yellow talil, crab, etc. An anchovy and sardine were caught mainly from March to July or August, horese mackerel and common mackerel from May to November. but puffer, swell fish, saury and filefish were caught mainly from April to October. 8. The sum of catch was largest in June, at which the wind direction was NE to SSW, the speed below 3.2m/sec, the atmospheric pressure below 1008mb, and precipitation beyond 154mm.

• Journal of the Korean earth science society
• /
• 제25권6호
• /
• pp.418-427
• /
• 2004

Recently, urban planning with consideration of urban climate, represented by the concept of urban ventilation lane is widely practiced in many countries. The concept of urban ventilation lane is mainly aimed to improve the thermal comfort within urban area in summer season. It has also the aim to reduce the urban air pollution by natural cold air drainage flows which are to be intensified by a suitable alignment of buildings as well as use zonings based on scientific reasons. In this study, the prevailing wind ventilation lane of a local wind circulation and around Daegu for a typical summer days was investigated by using a numerical simulation. The transport of air pollutants by the local circulation winds was also investigated by using the numerical simulation model, the RAMS (Reasonal Atmospheric Model System).The domain of interest is the vicinity of Daegu metropolitan city (about 900 km2). The horizontal scale of the area is about 30 km. The simulations were conducted under a late spring synoptic condition with weak gradient wind and almost clear sky. From the numerical experiment, the following three conclusions were obtained: (1) The major wind passages of the local circulation wind generated by radiative cooling over the representative mountains of Daegu (Mt. Palgong and Mt. Ap) were found. The winds blow down along the valley axis over the eastern part of Daegu as a gravity flow during nighttime. (2) At the flatland, the winds blow toward the western part of Daegu through the city center. (3) As the results, the air pollutants were transported toward the western part of Daegu by the winds during nighttime.

• Korean Journal of Remote Sensing
• /
• 제36권5_1호
• /
• pp.693-706
• /
• 2020

For ten meteorological observatories running an automated synoptic observing system (ASOS), we classified the observation environments into five classes based on the World Meteorological Organization (WMO) classification guidelines. Obstacles (such as topography and buildings) and land-cover types were the main factors in evaluating the observation environments for the sunshine duration, air-temperature, and surface wind. We used the digital maps of topography, buildings, and land-cover types. The observation environment of the sunshine duration was most affected by the surrounding buildings when the solar altitude angle was low around the sunrise and sunset. The air-temperature observation environment was determined based on not only the solar altitude angle but the distance between the heat/water source and ASOS. There was no water source around the ASOSs considered in this study. Heat sources located near some ASOSs were not large enough to affect the observation environment. We evaluated the surface wind observation environment based on the roughness length around the ASOS and the distance between surrounding buildings and the ASOS. Most ASOSs lay at a higher altitude than the surroundings and the roughness lengths around the ASOSs were small enough to satisfy the condition for the best level.