• 한국산업보건학회지
• /
• 제21권3호
• /
• pp.123-127
• /
• 2011

Objectives: The purpose of this study was to investigate the status of asbestos-containing materials (ACMs) used on ships and to consider measures for preventing worker exposure to asbestos fibers. Methods: A total of 17 ships including 16 ships under repair and a ship under construction at shipyards in Korea were investigated. Bulk samples were collected from suspected ACMs on engine exhaust pipes, boiler steam pipes, generator exhaust pipes, and etc. in ships in order to identify the presence of ACMs. Types and contents of asbestos were determined using polarized light microscopy (PLM). Results: ACMs were found from 14 ships out of 17 ships investigated. Only chrysotile asbestos was found from all samples. ACMs were mainly found from samples collected at the exhaust pipes of the engine, generator and incinerator, and boiler steam pipes where exhaust gases or steam of high temperature pass through. In most cases, types of ACMs were asbestos-containing fabrics such as asbestos tape. Friable ACMs were also found in some cases. Use of ACMs on ships was relevant to built time and owner of the ships rather than type and tonnage of the ships. Conclusions: ACMs were found from most ships built prior to 2000s. Therefore, measures for preventing asbestos-related diseases such as preparation of asbestos map on the ship and installation of warning signs, hazard communication with workers (ship-repairing workers, engine room workers and etc.), and follow-up for worker's health management are needed.

• 한국대기환경학회:학술대회논문집
• /
• 한국대기환경학회 2008년도 추계학술대회 논문집
• /
• pp.352-354
• /
• 2008

• 한국산업보건학회지
• /
• 제25권2호
• /
• pp.184-193
• /
• 2015

Objectives: This study focused on three aspects: characterizing concentrations of airborne particles by size distributions and asbestos fibers generated by various building materials; analyzing the characteristics of fibers produced by each simulation and asbestos fibers released from ACBMs; and investigating correlations of airborne asbestos fibers and particles generated and association of particle and asbestos concentrations. Methods: We selected three ACBMs including an insulation board, cement asbestos slate and wallboard. We constructed 4 scenarios; a) crushing with a hammer; b) cutting with a industrial knife; c) brushing with a metal brush; and d) tightening & loosening with a hand drill. We implemented one simulation for 30 seconds followed by 30 seconds resting period. We repeated a total of 5 cycles for 5 minutes. Results: The highest concentration of particulate & fibrous matters was from crushing with a hammer in each scenario followed by brushing with a metal brush, cutting with a industrial knife, and tightening & loosening with a hand drill. For ACBMs studied, asbestos concentrations were highest from an insulation board followed by cement asbestos slate, and wallboard. No difference in terms of concentration was found between an insulation board and asbestos slate. Fibers with $5{\sim}20{\mu}m$ in length were included in 76~90% of total fibrous matters. The distribution of the straight form fibers was greater than that of the curl form. About 90% of $PM_{Total}$ released from ACBMs was consisted of $PM_{10}$ while only 10% of $PM_{Total}$ was $PM_{2.5}$. Particulate matters like $PM_{2.5}$ was significantly correlated with fibrous matters($R^2=0.81$). Conclusions: We found ACBMs can significantly release asbestos fibers as well as $PM_{2.5}$. Concentrations of asbestos generated by ACBMs were well correlated with $PM_{2.5}$.

• 한국산업보건학회지
• /
• 제25권2호
• /
• pp.174-183
• /
• 2015

Objectives: The objective of this study is the estimation of factors influencing airborne fiber concentrations by means of an observation survey of asbestos-containing materials in buildings. Methods: Forty-five samples were collected from four commercial buildings by NIOSH Method 7400 and classified according to current condition, potential activity, construction year, and operations and maintenance(O&M). Results: Airborne fiber concentrations by current condition(classified as good, fair and poor) were significantly different(p<0.05). Concentrations by potential activity were significantly different among groups(p<0.05), and those from the low activity group were higher than those from the middle activity group. Based on construction year, airborne fiber concentrations from the decade of the 1990's were higher than those from the 1960's. When O&M status was considered, airborne fiber concentrations from 1960's buildings were lower than those buildings not operated and maintained(p<0.01), because dust generation was influenced by O&M status. It was found that airborne fiber concentrations were related to current condition and potential activity via regression analysis, but the coefficient of determination was low. Also, correlation analysis showed that the higher the potential activity, the more current condition is worsened, but the relationship was not significant(r=-0.455, p>0.05). Conclusions: Airborne fiber concentrations in asbestos-containing buildings had weak relationships with current condition and potential activity.

• 한국산업보건학회지
• /
• 제26권4호
• /
• pp.454-465
• /
• 2016

Objectives: The purpose of this study was to evaluate trends in asbestos exposure among asbestos-handling industries from 2000 to 2005. Methods: The data included the number of industries and workers exposed, concentrations of asbestos and the amount exceeded, and the type and size of industry by year. These data were collected by 46 regional employment and labor offices in Korea using work environment monitoring reports. A total of 1,481 samples from 284 industries were extracted from the reports and were analyzed with no data modification. Results: The means of asbestos concentration decreased from $0.84f/cm^3$ to $0.03f/cm^3$ during the period 2000-2005. Among the total of 1,481 samples, 11 samples(0.7%) exceeded the KOEL, and 178 samples(12.0%) were ACGIH TLV. The insulating paper product manufacturing industry was found to have the highest level of asbestos, followed by the fireproofing manufacturing industry, brake lining products manufacturing industry, commutator products manufacturing industries, and construction materials manufacturing industry. The number of asbestos handling industries decreased from 48 industries with 1,155 employees to 37 industries during the period of 2000 to 2005, but the number of asbestos workers expanded to the point that 1,182 employees could be found in 2005. Conclusion: Based on these results, the strengthening of the KOEL and new regulations turned out to help reduce asbestos exposure levels. This study recommends that retrospective exposure to asbestos based on various industry types should be assessed.

• 한국대기환경학회지
• /
• 제9권3호
• /
• pp.191-199
• /
• 1993

This paper describes the results of a systematic study to determine the characteristics of particle generated from various types of asbestos containing material(ACM) and manmade fiber material(MMFM) during operations of cutting and grinding in laboratory and workplace. Tests were conducted with a specially designed glove box which allowed complete sampling of the generated asbestos fibers. Specificially, air measurements were made during ACM and MMFM installation in building. All personal air samples collected were identified by polarized light microscopy(PLM), X-ray diffraction(XRD) and scanning electron microscope with energy dispersive X-ray analysis(SEM/EDXA). Also, the samples were counted by phase contrast microscope(PCM) in order to compare the results with the permissible exposure standard for workplace. Results indicate that the characterisitcs of fibers found in the roofing sheet, the ceiling and the wall insulation boards were identical to those of asbestos, while the characteristics of fibers found in the ceiling insulation board, the floor tile and the sprayed on insulation products in parking area were identical to those of asbestos, while the characteristics of fibers found in the ceiling insulation board, the floor tile and the sprayed on insulation products in parking area were identical to those of rock wool. The concentrations of airborne fibers from various building materials cut by a grinder for 5 minutes were in the ranges of 0.09 $\sim$ 1.71 fibers/cc(f/cc). The highest concentration(1.71f/cc) was found during grinding the wall insulation board which also contains rock wool. The airborne fiber concentrations generated by installing at workplace were ranged from 0.0009 to 0.029 f/cc. All asbestos fibers from the ceiling insulation board at workplace were less than 20$\mu$m in length and more than 20% of them had the average aspect ratio greater than 20. Therefore, for the purpose of decreasing asbestos and man-made fiber concentrations at the workplace, the ceiling and wall board should use strong binding material to increase the binding force with fiber. Also, the permissible exposure standard for workplace(2.0f/cc) in Korea should be constituted below the maximum avaiable concentration measured at glove box.

• 한국산업보건학회지
• /
• 제21권3호
• /
• pp.139-145
• /
• 2011

Objectives: This investigation is purposed to evaluate the airborne asbestos concentrations in the public buildings having asbestos containing materials(ACMs) in Seoul. Methods: The Seoul Metropolitan Government carried out an asbestos survey to the city-owned public buildings to identify the level of risk exposure, classified into low, moderate and high risk. To evaluate the airborne concentration of asbestos, 11 sampling sites in ten buildings based on the survey were selected. The air samples from the eleven sites were analyzed by Phase Contrast Microscopy(PCM) and Transmission Electron Microscopy (TEM), and compared the analytical results from the both. Results: 1. The airborne fiber concentrations by PCM were less than the detection limit($7f/mm^2$) in 9(82%) out of 11 sampling sites. The highest concentration was 0.0043 f/cc, but it was below the guideline value for indoor air quality(0.01 f/cc), proposed by the Ministry of Environment, Korea. 2. In two sampling sites, having moderate risk level, the chrysotile was identified and showed it's concentrations of 0.0102 s/cc and 0.0058 s/cc, less than $5{\mu}m$ lengths. 3. The ACMs identified in the two sampling sites were a packing material(65% of chrysotile) in mechanical area and a thermal system insulation(5% of chrysotile) in a boiler room. Having more possibility of asbestos emission in the mechanical area, it would be required to set up and carry out the asbestos management plan. Conclusions: Based on the result of this study, the airborne asbestos concentrations in the public buildings with ACMs were generally lower than the guideline value for indoor air quality. There are widespread concerns about the possible health risk resulting from the presence of airborne asbestos fibers in the public buildings. Most of the previous studies about airborne asbestos analysis in Korea were performed based on PCM method that asbestos and non-asbestos fibers are counted together. In the public and commercial buildings, having ACMs, it is suggested that the asbestos be analyzed by TEM method to identify asbestos due to concerns about asbestos exposure to workers and unspecified people.

• 분석과학
• /
• 제27권3호
• /
• pp.153-160
• /
• 2014

세계적으로 석면분석방법에 관한 다양한 연구사례가 발표되고 있는 가운데, 분석방법의 차이에 따른 석면함유물질(ACM, Asbestos Containing Material) 결과에 대한 관심이 대두되고 있다. 본 연구에서는 균질성이 확보된 ACM 시료를 시야평가법(visual estimation method)과 포인트계수법(point counting method)의 분석결과에 대한 비교 평가를 통하여 분석기관 및 분석자의 신뢰성 향상과 더불어 편광현미경 분석의 기초자료를 확보고자 하였다. 석면분석은 정성분석과 정량분석으로 구분하였으며, 석면정량을 위한 방법은 EPA 600-R-93-116의 시야평가법과 포인트계수법으로 총 400지점을 계수하는 방법으로 실시하였다. 먼저 준비된 시료의 균질성을 분산분석을 이용하여 확인한 결과 이상이 없음을 확인하였다. 정성분석의 결과는 백석면과 갈석면으로 확인되었고 정량분석결과는 포인트계수법이 시야평가법과 비교하여 전체적인 석면함유량이 저평가되는 경향과 함께 포인트계수법은 분석과정이 조금 복잡하고 분석시간이 많이 소요되었다.

• 자원환경지질
• /
• 제51권4호
• /
• pp.309-322
• /
• 2018

석면이 '1급 발암물질'로 지정되어 국내 외적으로 사회적 관심이 높아지면서, 폐석면 광산 또는 자연적으로 산출되는 석면에 대한 특성과 위해성에 대한 연구의 필요성이 제기되고 있다. 기존 연구는 (초)염기성암에서 산출되는 석면에 관한 연구에 국한되어 있으며, 변성퇴적암류인 탄산염암에서 산출되는 자연발생석면에 대한 연구는 상대적으로 미비하다. 따라서 이 연구는 국내 탄산염암에서 산출되는 자연발생석면의 산출양상 및 광물학적 특성을 파악하고자 하였다. 연구 지역인 충청남도 아산과 전라북도 무주 및 장수 일대에는 선캠브리아기 편마암 내에 탄산염암이 분포하고, 주변에는 고생대, 중생대의 화강암이 널리 분포되어 있다. 시료는 탄산염암 일대의 석면함유 암석시료로 cross/mass/slip fiber 형태 등의 섬유상 광물이 관찰되는 부분과 모암인 탄산염암을 대상으로 채취하였으며, XRD, PLM, EPMA SEM-EDS 분석을 실시하여 탄산염암에서 산출되는 자연발생석면의 광물학적 특성을 연구하고자 하였다. 연구결과, 아산, 무주, 그리고 장수지역의 탄산염암 내에서 산출되는 자연발생석면으로 각섬석군 투각섬석이 확인되었다. 석면의 산출은 모암인 탄산염암 내에서 cross/mass/slip fiber 형태로 존재하고 있었다. 또한 자연발생석면과 형태적 유사성을 가지며 석면함유가능물질에 포함되는 활석, 질석, 해포석이 함께 산출되었다. 이러한 세지역의 투각섬석은 일반적인 석면형 기준과 일치하는 길이 $5{\mu}m$ 이상, 종횡비 3:1 이상으로 나타났다. 세 지역의 탄산염암 내에서 산출되는 투각섬석은 석면형과 비석면으로 모두 존재하고 있으며, 풍화와 같은 지질과정과 환경적인 요인에 따라 비석면형도 쪼개지면 가늘고 긴 석면형이 될 수 있음을 확인하였다. 지질학적 및 지구화학적 특성과 광물조성과 그 산출양상을 보았을 때 탄산염암 주변으로 관입한 규질 화성암의 영향에 의한 열수변질작용이나 열수 충진작용 등에 의해 형성되었을 것으로 사료된다.

• 자원환경지질
• /
• 제56권4호
• /
• pp.457-473
• /
• 2023

석면은 악성중피종과 폐암 등 치명적인 질병을 유발하기 때문에 국내에서 2009년부터 그 사용이 전반적으로 금지되었다. 그러나 국내에서 지난 수십년 간 석면이 생산 및 수입되어 다양한 산업에서 사용되어 왔기 때문에 우리 주변에는 여전히 석면함유물질이 많이 존재하고 있어 안전한 관리가 절실하다. 이 연구는 지난 32년(1991년 ~ 2022년)동안의 빅데이터를 바탕으로 석면관련 주요키워드를 이용하여 석면관련 트렌드 변화를 살펴보고자 한다. 또한 국내 과거(1990년 이전)의 석면의 생산, 수입, 사용 실태와 더불어 현재(2023년~2027년)의 석면관련 정책 동향을 살펴보고자 하였다. 1991~2000년에는 국내 석면의 생산과 수입 그리고 이용으로 인하여 석면에 대한 발암성이 부각되는 시기로 연구, 근로자, 발암물질, 환경등과 관련된 키워드가 주를 이루었다. 2001~2010년에는 석면의 발암성과 관련하여 미국, 일본 등에서 소송이 시작되었던 시기로 폐암, 소송, 발암물질, 노출, 기업 등의 키워드가 주를 이루었다. 2011~2020년에는 국내에서도 석면문제의 심각성을 인지하는 키워드인 발암물질, 야구장, 학교, 슬레이트, 건축물, 폐석면광산 등이 지속적으로 상위권 키워드로 검색되었다. 2021년부터는 주로 검색되는 키워드는 학교, 슬레이트, 건축물 등과 조경석, 환경영향평가, 아파트, 시멘트 등의 키워드가 나타났다.