• Fashion & Textile Research Journal
• /
• v.15 no.3
• /
• pp.444-451
• /
• 2013

This paper surveys the physical properties of aramid and aramid/nylon hybrid air-jet textured yarns(ATY) for protective garments according to wet and dry texturing conditions. Aramid and nylon filaments were used to make two kinds of para-aramid ATY and four kinds of aramid/nylon hybrid ATY with dry and wet treatments. The analyzed physical properties of six specimens (made on the ATY machine) are as follows. The tenacity and initial modulus of aramid and aramid/nylon hybrid ATY decreased with the wetting and breaking strain; however, the yarn linear density of aramid and hybrid ATY increased with wetting treatment. The dry and wet thermal shrinkage of the hybrid ATY increased with wetting. The stability of aramid and hybrid ATY also increased with wetting. The physical properties of core/effect type hybrid ATY showed significantly more change than the core type hybrid ATY and the physical properties of nylon/aramid core/effect hybrid ATY showed significantly more change than the of aramid/nylon core/effect hybrid ATY. A higher bulky and breaking strain of hybrid ATY require ATY processing conditions of nylon on the core part with wetting and aramid on the effect part. ATY processing conditions for nylon and aramid on the core part with wetting are required for a higher tenacity and modulus. ATY processing conditions of nylon and aramid on the core with no wetting are required for a low thermal shrinkage.

• Polymer(Korea)
• /
• v.37 no.2
• /
• pp.196-203
• /
• 2013

Surface modification of meta-aramid fibers was performed by phosphoric acid treatment. Surface morphology and element composition of untreated and treated fibers were analyzed by scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). Effects of surface modification on the mechanical strength of aramid papers made from meta-aramid fibers and fibrid were investigated. Surface modification conditions were optimized by response surface analysis (RSA). Results show that phosphoric acid treatment increases the surface roughness and oxygen content of aramid fibers. They improve the interface bonding strength between aramid fibers and fibrid, which improves the tensile strength of aramid papers. The results of response surface analysis indicate that the tensile strength of aramid papers increases by 47.5% and reaches the maximum when meta-aramid fibers are treated with 21.1wt% phosphoric acid solution at $39.3^{\circ}C$ for 36.7 min.

• Science of Emotion and Sensibility
• /
• v.17 no.3
• /
• pp.75-82
• /
• 2014

This study investigated the physical properties of aramid/nylon ATY and aramid ATY for protective garments according to the aramid and nylon characteristics fed on the core and effect components of air jet texturing equipment. Tenacity decrease of aramid ATY was much more higher than that of nylon ATY because of slick of aramid filament surface. Tenacity of aramid/nylon ATY was most affected by the tenacity of nylon on the effect component of ATY. Breaking strain of nylon ATY was two times higher than that of nylon before air jet texturing, then, in case of aramid ATY and aramid/nylon ATY, were 5.9-6.7 times higher than those before air jet texturing. Initial modulus decrease of aramid ATY showed 86.5% of initial modulus of aramid before air jet texturing, then aramid/nylon hibrid ATY showed arithmetic average value of initial modulus of aramid and nylon ATY. Wet and dry thermal shrinkages of aramid/nylon hybrid ATY were dominated by those of nylon filament on the effect component of ATY.

• Fashion & Textile Research Journal
• /
• v.15 no.3
• /
• pp.437-443
• /
• 2013

This paper investigates the physical properties of aramid and aramid/nylon hybrid air jet textured filaments for protective garments relative to ATY nozzle diameters. Three types of para-aramids(840d, 1,000d, 1,500d) and nylon(420d) filaments were prepared; in addition, 840d aramid/420d nylon and three kinds of aramid filaments were texturized with a variation of air jet nozzle diameters(0.6, 0.75, 1 and 1.2 mm) on the AIKI air jet texturing machine. The measured physical properties of 16 specimens are as follows. The linear densities of aramid and aramid/nylon hybrid ATY increased with a larger nozzle diameter. The tenacity and initial modulus of aramid and hybrid ATY linearly decreased with a larger nozzle diameter; in addition, the breaking strain increased with the nozzle diameter. The dry and wet thermal shrinkage of hybrid ATY increased with a larger nozzle diameter from 0.6 mm to 1 mm and then decreased at a nozzle diameter of 1.2 mm (which seems to be a critical diameter). The wet and dry thermal shrinkage of aramid/nylon hybrid ATY are influenced by the nylon part of the hybrid yarns because the wet and dry thermal shrinkages of aramid ATY are less than 0.2%. The instabilities of aramid and aramid/nylon hybrid ATY were not influenced by the air jet nozzle diameter; however, they increased with the linear density of ATY.

• Textile Coloration and Finishing
• /
• v.21 no.5
• /
• pp.58-62
• /
• 2009

Poly(m-phenyleneisophthalamide), m-aramid has no adjacent $\alpha$-hydrogen of a nitrogen-halogen bond causes dehydrohalogenation. This fact proposes that m-aramid is one of good antimicrobial precursors. To enhance the surface area of m-aramid, electrospinning was employed. Scanning electron microscopy(SEM) was conducted to inspect the morphology change of m-aramid. The surface area of regular and electrospun m-aramid was calculated. Swatch test was applied to measure antimicrobial activity of the samples. The results showed that within 10 min contact time the electrospun m-aramid inactivated Escherichia coli KCTC 1039 (Gram-negative bacteria) with 8 log reductions.

• Textile Coloration and Finishing
• /
• v.33 no.4
• /
• pp.327-337
• /
• 2021

The uniformly dispersed Aramid and Poly (phenylene benzobisoxazole) (PBO) in a variety of rubber was investigated. The mechanical properties of rubber were characterized by hardness, tensile strength, elongation at break, heat resistance, oil resistance, cold resistance, ozone resistance measurements. The 3mm Aramid chopped fiber better tensile strength than the other Chopped fiber. The Aramid of 3mm chopped fiber showed excellent reinforcing in rubber composite because of homogeneous dispersion. Consequently, the best 3mm Aramid chopped fiber and rubber improved the tensile strength and elongation at break of the composite. Also, 3mm Aramid chopped fiber improved the oil-resistant, ozone resistant and cold resistant.

• Textile Coloration and Finishing
• /
• v.23 no.4
• /
• pp.298-303
• /
• 2011

Aramid fibers have been widely used as the reinforcement for composites due to their high modulus and strength. Nowadays the safety measures is required to improve the personal protection. The dyeing of aramid fibers is considered to be very difficult and their dyeing mechanism is not well illucidated. Therefore, this study is to establish the dyeing & printing technology for aramid fibers. The effects of swelling agent and neutral salt in the dye bath on the obtained colors were studied. Also dyeing method of aramid fibers depending on dyeing temperature and dye concentration were established. Color fastness of the dyed aramid fabric with cationic dyes were acceptable excluding light fastness.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.89-89
• /
• 2012

선행 연구에서는 m-Aramid와 p-Aramid의 Ring 방적사/Core 방적사 조건에 따른 방적사 물성에 대해서 연구하였는데, Ring 방적사의 혼용율, 스핀들 속도에 따른 물성 변화, Core 방적사의 공정특성에 따른 방적성, 피복성에 대해 연구를 하였다. 그 결과 Ring 방적사의 경우 m-Aramid의 혼용율이 증가할수록 사 강도는 증가하는 경향을 확인할 수 있었고, 스핀들 속도가 증가함에 따라서 불균제도 및 사결점이 다소 증가하였다. Core 방적사의 경우 Core에 p-Aramid를 사용했을 때 방적성과 피복성은 양호 하였지만, 강한 p-Aramid에 의해 톱 롤러코트의 마모가 되는 경향을 볼 수 있었다. 본 연구에서는 Ring 방적사/Core 방적사에 대해 좀더 구체적인 제조공정조건에 의한 물성 변화를 알아보았고, 좀더 다양한 섬유소재를 적용해서 제조하였다. Ring 방적사의 경우 p-Aramid 혼용율에 따른 실험을 하였는데, m-Aramid에 대한 p-Aramid의 혼용율을 0%, 5%, 10%, 20% 로 하여 Ne30을 제조하였으며, Core 방적사는 Core를 p-Aramid 200D로 하고 Sheath를 Cotton으로 하여 Core 공급속도비 (1.06, 1.10, 1.14), 연계수(T/M, 3.8, 4.0, 4.2), Sheath/Core 혼섬율(70/30, 60/40, 50/50)에 따라 제조하였다. 추가로 Core 방적사는 Sheath에 Cotton 대신 FR-Rayon과 선염 Cotton을 사용하여 각각 Sheath/Core 혼섬율 70/30의 비율로 방적사를 제조하여 다양한 소재에 따른 방적사의 물성을 측정하였다. 제조된 시험 원사들의 측정 물성은 번수(Ne), 균제도(U%), 사결점(IPI), 강력(cN), 신도(%), 비강도(cN/Tex) 등이며, 편직을 통해 편성물의 외관을 확인하였다. Ring 방적사의 경우 p-Aramid의 혼용율이 증가할수록 강도는 완만하게 증가한 반면, 신도는 급격하게 감소하였다. Cotton Core 방적사의 경우는 공급속도비가 높아질수록 균제도가 높아지는 것을 볼수 있었고, Core 공급속도비가 높아질수록 외관상 피복도는 높아진 것을 볼 수 있었다. 이렇게 연구된 Aramid 소재를 이용한 방적사 제조 공정조건변화에 따른 물성 및 피복도 결과는 기존 방적업체에서 Aramid를 이용한 방적사 제조시에 공정조건을 확보하는데 도움이 될 것이라 생각되며, 방적사 시제품 생산시에 발생할 수 있는 시행착오를 줄임으로써 시제품 제조를 위한 생산비용의 Loss를 절감할 수 있을 것으로 예상된다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.908-912
• /
• 1996

FRMLs consist of thin sheets of high strength metal, which are laminated using a structural adhesive and high strength fibers. ARALL(Aramid-fiber Reinforced Aluminum alloy Laminates) of FRMLs is a new class of hybrid material. HERALL(Heracron Reinforced Aluminum Laminate) i.e. domestic ARALL is made of homemade aramid fibers, adhesives and adhesive technique. Domestic aramid fiber is Heracron manufactured by KOLON and domestic adhesive is epoxy resin manufactured by Han Kuk Fiber. In this study, Fatigue crack propagation behavior was examined in a 2024-T3 aluminum alloy/aramid-fiber epoxy 3/2 laminated composites, HERALL and ARAL $L^{ⓡ}$-2 LAMINATE comparing with 2024-T3 aluminum alloy. The extrinsic toughening mechanisms in HERALL and ARALL were examined, the crack bridging behavior of fibers was analyzed by new algorithm, which measures crack bridging stress, and the crack bridging zone length was measured.

• Tribology and Lubricants
• /
• v.15 no.4
• /
• pp.314-320
• /
• 1999

Friction and wear characteristics of phenolic resin-based friction materials reinforced with aramid pulp and potassium titanate were investigated using a pad-on-disk type friction tester. Friction characteristics such as friction stability, thermal stability, and wear rate varied according to the type of phenolic resins and the relative amount of aramid pulp and potassium titanate. The modified novolac resin-based friction materials showed better heat resistance and friction stability than those with the unmodified(straight) novolac resin. Compared with friction materials filled with potassium titanate or aramid pulp only, the friction materials reinforced with both aramid pulp and potassium titanate showed good friction stability and wear resistance. Increment of aramid pulp from 10 to 20 vol.% however, showed little difference in friction stability.