• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.663-666
• /
• 1999

Ground Penetrating Radar (GPR) attached with 1 GHz center frequency antenna has been used to measure a dielectric constant of mortar, and to detect and locate a steel bar embedded inside laboratory size mortar specimens at various depth. Mortar specimens are made for the measurements with the dimensions of 100cm (width)$\times$100cm (length)$\times$14cm (depth). Each specimen has a 13mm diameter D13 steel bar at 2, 4, 6, 8, 10 and 12cm depth. In this paper, results of radar measurments are provided with a sample output, which successfully located the bar. It has been found that the reflected wave of the steel bar interacts with that of surface when the steel bar has the close distance to the surface.

• Journal of electromagnetic engineering and science
• /
• v.3 no.1
• /
• pp.62-66
• /
• 2003

Novel coupled line phase shifters and its equivalent phase delay line for compact broadband phased array antennas are proposed. These phase control circuits are designed to be less complex, small size and to use a less number of active devices. The phase shifter is able to control a 120$^{\circ}$ phase shift continuously, and the phase delay line for a reference phase has a fixed 60$^{\circ}$ shifted phase. Both have the low phase error of less than $\pm$3.5$^{\circ}$ and the low gain variations of less than 1 ㏈ within the 300 MHz bandwidth. These proposed circuits are adequate to form the efficient beam-forming networks with compactness, broadband, less complexity, and low cost.

• Journal of the Optical Society of Korea
• /
• v.16 no.1
• /
• pp.47-52
• /
• 2012

The use of a $Ti:LiNbO_3$ symmetric Mach-Zehnder interferometric intensity modulator with a push-pull lumped electrode and a plate-type probe antenna to measure an electric field strength is described. The modulator has a small device size of $46{\times}7{\times}1mm$ and operates at a wavelength of $1.3{\mu}m$. The output characteristic of the interferometer shows the modulation depth of 100% and 75%, and $V_{\pi}$ voltage of 6.6 V, and 6.6 V at the 200 Hz and 1 KHz, respectively. The minimum detectable electric field is ~1.84 V/m, ~3.28 V/m, and ~11.6 V/m, corresponding to a dynamic range of about ~22 dB, ~17 dB, and ~6 dB at frequencies of 500 KHz, 1 MHz and 5 MHz, respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.147-151
• /
• 2000

This paper presents an analysis of a slot on the broad wall of a rectangular waveguide using the 3D FDTD method. In order to reduce the reflection loss, Mur's 2nd absorbing boundary condition is used. To realize the optimum design by FDTD, the effects of time step, excitation aperture size, analysis region and excitation position in model are derived. The analysis results are compared with the experimental results and they show a good agreement with each other.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.6 no.3
• /
• pp.169-174
• /
• 2006

In this work, we demonstrate a novel compact mechanical beam steering transmitter based on a direct vertical integration of a 2-D MEMS-based mechanical beam steering antenna with a VCO on a single silicon platform. By eliminating the long feed lines and waveguide metal blocks, the radiation pattern has been improved vastly, resulting in an almost ideal pattern at every scan angle. The losses incurred by the feed lines and phase shifters are also eliminated, which allows the transmitter to be implemented using only a single VCO. The system complexity has been greatly reduced with a total module size of only 1.5 cm ${\times}$ 1.5 cm ${\times}$ 0.4 cm. This work demonstrates that RF MEMS can be a key enabling technology for high-level integration.

• Applied Science and Convergence Technology
• /
• v.23 no.4
• /
• pp.161-168
• /
• 2014

A real-time monitoring of immersed antenna type inductively coupled plasma (ICP) was done with a homemade 2 dimensional voltage probe array to check the uniformity of the plasma. Measured voltage values with a high impedance voltmeter are close to the floating potential of the plasma. As the substrate carrier was moving into a magnetron sputtering plasma diffusive from a $125mm{\times}625mm$ size cathode, measured results showed reliably separation of plasma into the upper and lower empty space over the carrier. Infra red thermal imaging camera was used to observe the cross corner effect in situ without eroding a target to the end of the usage. 3 dimensional particle trace model was used to analyze the magnetron discharge's behavior.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2041-2043
• /
• 1999

In order to investigate the radiation characteristics of unmixed line noise from overhead high voltage AC transmission lines, a gap noise generator was manufactured. Disk size which decides capacitance between the noise generator and earth was selected through preliminary indoor experiments and analysis by charge simulation method. The capacitance is one of principal parameters related to inject a proper noise current into lines. The field experiments were performed with the noise generator installed in Kochang 765 kV full scale test line. As the results, the useful data which can be used to analysis the radiation characteristics of noise from transmission lines was obtained. Those are lateral profiles the directivity of antenna toward lines, frequency spectra and so on.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.4
• /
• pp.84-91
• /
• 1996

Input filter for satellite communication transponder is the interface between the antenna and the receiver. It is used to provide the selection of the uplink signals with minimum insertion loss and to prevent downlink signals form reaching the LNA. This paper is intended to provide a description of the input filter for KOREASAT communication transponder. Included are description for the electrical and mechanical design and the requirments of environmental test. In expecting the electrical performine the optimum electrical configuration ot meet all requirements are performed. Mechanical requirements are charactersed by several constraints for weight, size of the filter and its type of input output interface. The standardized environmental tests are performed to confirm satisfactory performance of the filter with respect to the requirements of vibration and thermal vacuum shocks.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.20 no.1
• /
• pp.77-83
• /
• 2002

Recently, the industrial development caused the expansion of city and the field of construction is being larged in size. So, information of construction buried in underground is necessary. In this paper, we were investigated the detachability on various specimen in self-designed test field using the GPR system with three antenna elements and it was constantly radiated 730 MHz frequency. To examine the detachability on various condition, the test were displayed B-scan CRT. And the pattern was exactly positioned when it was compared to the real buried-depth. Therefore, we can confirm similarity between the wave-propagation velocity and previous results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.5
• /
• pp.407-411
• /
• 2005

A simulation investigation on the circular cylindrical reentrant cavity with axial ridges and a cylindrical circumferential slot is presented. This study indicates that by properly adjusting the dimensions of the ridge sand the slot, the size of the cavity can be miniaturized to around $\lambda_0$ The simulation results using CST MWS show good agreement with past theoretical predictions and provide useful insight into fundamental concerns associated with electrically small antennas.