• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.159-162
• /
• 1999

All solid state thin film micro-batteries consisting of lithium metal anode, an amorphous LiPON electrolyte and cathode of vanadium oxide have been fabricated and characterized, which were fabricated with cell structure of Li/LiPON/V$_2$O$\sub$5/Pt. The vanadium oxide thin films were formed by d.c. reactive sputtering on Pt current collector. After deposition of vanadium oxide films, in-situ growths of lithium phosphorus oxynitride film were conducted by r.f. sputtering of Li$_3$PO$_4$ target in mixture gas of N$_2$ and O$_2$. The pure metal lithium film was deposited by thermal evaporation on thin film LiPON electrolyte. The cell capacity was about 45${\mu}$Ah/$\textrm{cm}^2$ $\mu\textrm{m}$ after 200 cycle. No appreciable degradation of the cell capacity could be observed after 50 cycles .

• Bulletin of the Korean Chemical Society
• /
• v.21 no.1
• /
• pp.44-48
• /
• 2000

Microbial fuel cells comprising the microorganism P. vulgaris, thionin as a mediator, and various mono- and disaccharides in an anodic compartment have been developed. A cathodic compartment containing a Pt electrode and Fe$(CN)_6^{3-}$ was separated from an anode by the Nafion membrane. From absorbance-time measurements, it was found that the absorbance of thionin was not altered by the addition of P. vulgaris, even in the presence of sugars. However, thionin was effectively reduced when P. vulgaris was present. These results differ substantially from the case of safranine O, a phenazine-derivative, indicating that thionin takes up electrons during the metabolic oxidation processes of carbohydrates. Maximum fuel cell efficiency was observed at 37 $^{\circ}C$, optimum temperature for the growth of P. vulgaris, and 0.5 V cell voltage was obtained, which indicates that the metabolism of the microorganism directly affects the efficiency. Thionin concentration was closely related to cell performance. When the charging-discharging characteristics were tested with glucose, galactose, sucrose, maltose, and trehalose as carbon sources, galactose was found to give the highest coulombic efficiency. Cell performance was almost fully recovered with only small degradation when glucose and sucrose were used in the repetitive operation. Current was maintained nearly twice as long for sucrose than in the case of glucose.

• Corrosion Science and Technology
• /
• v.22 no.4
• /
• pp.287-296
• /
• 2023

Li-ion batteries have been gaining increasing importance, driven by the growing utilization of renewable energy and the expansion of electric vehicles. To meet market demands, it is essential to ensure high energy density and battery safety. All-solid-state batteries (ASSBs) have attracted significant attention as a potential solution. Among the advantages, they operate with an ion-conductive solid electrolyte instead of a liquid electrolyte therefore significantly reducing the risk of fire. In addition, by using high-capacity alternative electrode materials, ASSBs offer a promising opportunity to enhance energy density, making them highly desirable in the automotive and secondary battery industries. In ASSBs, Li metal can be used as the anode, providing a high theoretical capacity (3860 mAh/g). However, challenges related to the high interfacial resistance between Li metal and solid electrolytes and those concerning material degradation during charge-discharge cycles need to be addressed for the successful commercialization of ASSBs. This review introduces and discusses the interfacial reactions between Li metal and solid electrolytes, along with research cases aiming to improve these interactions. Additionally, future development directions in this field are explored.

• Korean Chemical Engineering Research
• /
• v.55 no.2
• /
• pp.242-246
• /
• 2017

The application of composite cathode materials including $LiFePO_4$ (lithium iron phosphate) of olivine crystal structure, which has high thermal stability, were investigated as alternatives for hybrid battery-capacitors with a $LiMn_2O_4$ (spinel crystal structure) cathode, which exhibits decreased performance at high temperatures due to Mn-dissolution. However, these composite cathode materials have been shown to have a reduction in capacity by conducting life cycle experiments in which a $LiFePO_4$/activated carbon cell was charged and discharged between 1.0 V and 2.3 V at two temperatures, $25^{\circ}C$ and $60^{\circ}C$, which caused a degradation of the anode due to the lowered voltage in the anode. To avoid the degradation of the anode, composite cathodes of $LiFePO_4/LiMn_2O_4$ (50:50 wt%), $LiFePO_4$/activated carbon (50:50 wt%) and $LiNi_{1/3}Co_{1/3}Mn_{1/3}O_2$ (50:50 wt%) were prepared and the life cycle experiments were conducted on these cells. The composite cathode including $LiNi_{1/3}Co_{1/3}Mn_{1/3}O_2$ of layered crystal structure showed stable voltage behavior. The discharge capacity retention ratio of $LiNi_{1/3}Co_{1/3}Mn_{1/3}O_2$ was about twice as high as that of a $LiFePO_4/LiMn_2O_4$ cell at thermal stability experiment for a duration of 1,000 hours charged at 2.3 V and a temperature of $80^{\circ}C$.

• Applied Chemistry for Engineering
• /
• v.21 no.6
• /
• pp.697-701
• /
• 2010

We investigate the cell performance and characteristics of a direct formic acid fuel cell (DFAFC) using palladium (Pd) as a catalyst for anode. Pd is deposited on the electrolyte using the "direct paint" method. From a continuous three time-test of the polarization curve of the DFAFC, it is found that the catalytic activity of Pd and the cell performance of DFAFC steadily degrade as the tests are proceeded. This behavior may be due to the deactivation of Pd by formate (COOH) and hydroxyl (OH) groups, which are electrochemically dissociated from formic acid solution. Estimations of the degradation, followed by reactivation in activity of Pd catalyst and DFAFC cell performance are implemented by linear voltage sweep tests going in both positive and negative directions. When the maximum voltage of 1.0 V versus DHE is applied to the cell while a linear voltage sweep test going in negative directions, the activity of Pd catalyst and the DFAFC cell performance recover by the rehabilitation in activity of the deactivated Pd.

• Journal of the Korean Electrochemical Society
• /
• v.18 no.2
• /
• pp.68-74
• /
• 2015

To compare the microstructure and electrochemical properties between two binary alloys (Cr-Si, Ni-Si), two composition of binary alloys with the same capacity were selected using phase-diagram and prepared by matrix-stabilization method to suppress the volume expansion of Si by inactive-matrix. Master alloys were made by Arc-melting followed by fine structured ribbon sample preparation by Rapid Solidification Process (RSP, Melt-spinning method) under the same conditions. Also powder samples were produced by wet grinding for X-Ray Diffraction (XRD) and electrochemical measurements. As predicted from the phase diagram, only active-Si and inactive-matrix ($CrSi_2$, $NiSi_2$) were detected. The results of Scanning Electron Microscope (SEM) and Transmission Electron Microscopy - Energy Dispersive X-ray Spectroscopy (TEM-EDS) show that Cr-Si alloy has finer microstructure than Ni-Si alloy, which was also predictable through phase diagram. The electrochemical properties related to microstructure were evaluated by coin type full- and half-cells. Separately, self-designed test-cells were used to measure the volume expansion of Si during reaction. Volume expansion of Cr-Si alloy electrode with finer microstructure was suppressed significantly and improved in cycle capability, in comparison Ni-Si alloy with coarse microstructure. From these, we could infer the correlation of microstructure, volume expansion and electrochemical degradation and these properties might be predicted by phase diagram.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.4
• /
• pp.377-383
• /
• 2017

This paper presents the performance characteristics of a 1 kW solid oxide fuel cell (SOFC) stack under various internal reforming and fuel utilization conditions. The Research Institute of Industrial Science & Technology (RIST) developed the 9-cell stack using a $20{\times}20cm^2$ anode supported planar cell with an active area of $324cm^2$. In this work, current-voltage characteristic test, fuel utilization test, continuous operation, and internal reforming test were carried out sequentially for 765 hours at a furnace temperature of $700^{\circ}C$. The influence of fuel utilization and internal reforming on the stack performance was analyzed. When the 1 kW stack was tested at a current of 145.8 A with a corresponding fuel utilization of 50-70% (internal reforming of 50%) and air utilization of 27%, the stack power was approximately 1.062-1.079 kW. Under continuous operation conditions, performance degradation rate was 2.16%/kh for 664 hours. The internal reforming characteristics of the stack were measured at a current of 145.8. A with a corresponding fuel utilization of 60-75%(internal reforming of 50-80%) and air utilization of 27%. As fuel utilization and internal reforming ratio increased, the stack power was decreased. The stack power change due to the internal reforming ratio difference was decreased with increasing fuel utilization.

• Korean Journal of Environmental Agriculture
• /
• v.26 no.2
• /
• pp.179-185
• /
• 2007

A new technology that utilizes a microbial fuel cell (MFC) has been developed to generate electricity directly from the oxidation of organic matters such as carbohydrates or complex organics in wastewater. Fermentation of these organic matters results in production of volatile fatty acids (VFAs), alcohols, $CO_2$ and $H_2$. We investigated the electricity-producing potential of the VFAs and actual food processing wastewater using a two-chambered MFC. The electrons produced by acetate degradation were proportional to acetate concentration in the medium. Acetate concentration and generated power were linearly correlated at a low range or acetate concentration (< 8 mg/L), but at above 8 mg/L of acetate the power produced was maintained at 0.1 mW. When butyrate was added to the anode acclimated to acetate, there was a lag period of 30 hr for electricity generation. However, when propionate was added to the same anode bottle, lag periods were not existed. The wastewater from baby food processing generated the maximum power density of $81{\pm}7\;mW/m^2$ of electricity and exhibited the Coulombic efficiencies of 27.1% and 40.5% based on TCOD and SCOD, respectively. Sugars in the food processing wastewater were reduced within 50 h from 230 mg/L < 30 mg/L.

• Composites Research
• /
• v.36 no.1
• /
• pp.37-41
• /
• 2023

The treated water inside the ballast electrolytic cell creates a highly alkaline atmosphere due to hydroxide generated at the DSA(Dimension Stable Anode) electrode during electrolysis. In this study, a composite material that can replace the weakness of the PE-coated steel pipe used in the existing ballast pipe was prepared. The test samples are BRE(Basalt fiber reinforced epoxy), BRP(Basalt fiber reinforced unsaturated polyester), GRE(Glass fiber reinforced epoxy), and GRP(Glass fiber reinforced unsaturated polyester). And then it was immersed in NaOH for 720 hours. The friction test of each specimen was conducted. The Friction coefficient analysis according to material friction depth and interfacial adhesion behavior between resin and fiber were analyzed. As a result, the mechanism of interfacial separation between resin and fiber could be analyzed. In the case of the unsaturated polyester resin with low interfacial bonding strength the longer the immersion time in the alkaline solution, the faster the internal deterioration caused by the deterioration that started from the surface, resulting in a decrease in the friction coefficient. It is hoped that this study will help to understand the degradation behavior of composite materials immersed in various chemical solutions such as NaOH, acid, and sodium hypochlorite in the future.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.660-666
• /
• 1998

We discussed structure, energy state, characteristics of thermal stability, and electrochemical properties of Li-GFICs, Li-PCICs, and Li-AGICs during the intercalation process. According to X-ray diffraction patterns, we observed phase of stage 2 mainly from Li-GFICs, while stage 1 phase as well as stage 2 from Li-PCICs. For the structure of Li-AGICs, stage 1 phase was dominant, but it was not possible to obtain pure stage 1 compound probably due to structural characteristics of artificial graphite. We measured energy state of the compounds to stage stability, and revealed that Li-AGICs and Li-GFICs were in more stable state than Li-PCICs. Therefore, those two compounds could be excellent candidate for energy reserve material. From the study of thermal degradation, Li-GFICs showed strong exothermic reaction at around 300 and $400^{\circ}C$. In the study of thermal stability of Li-AGIC at various temperatures, we observed that lithium was not completely deintercalated and high stage was maintained even at high temperature. In the case of charge, discharge, and electrochemical studies, Li-GFICs showed the best results.