• Korean Chemical Engineering Research
• /
• v.45 no.5
• /
• pp.515-522
• /
• 2007

In this study we have attempted to evaluate the technical feasibility of "BB-HY", which is depleted gas reservoir as a gas storage field, using the commercial compositional simulator "ECLIPSE 300". The "BB-HY" reservoir has an initial gas in place of 143 BCF which is relatively small, and its porosity and permeability are 19.5% and 50 md, respectively. For "BB-HY" gas reservoir, we have performed a feasibility analysis by investigating the cushion gas (or working gas), converting time to gas storage field, operation cycle, number of wells and the possible application of horizontal borehole as well. From the simulation results, it was found that the amount of cushion gas in "BB-HY" reservoir is required at least 50% of IGIP in order to operate stably as gas storage field. When one produces gas for longer time and hence the remaining gas in reservoir is less than optimal cushion gas, no technical problem was occurred as long as additional cushion gas is injected up to the optimal cushion gas. In the case of changing the operation cycle into producing gas for three months during winter season from producing five months, the result shows that either the cushion gas should be greater than 60% or the more number of wells should be drilled. Meanwhile, from the results of sensitivity analysis for the number of wells, in cases of operating six or eight vertical wells, the stable reproduction of the injected gas can not be possible in "BB-HY" gas reservoir since the remaining gas in reservoir is increased. Therefore, in "BB-HY" reservoir, at least ten vertical wells should be drilled for the stable operation of gas. This time, when three horizontal wells are additionally drilled including the existing two vertical wells, it was found that the operation of injection and reproduction of gas is relatively stable in "BB-HY" gas reservoir.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.8
• /
• pp.844-851
• /
• 2005

The purpose of this study was to determine feasibility of application of regenerated or recycled $TiO_2$ on the successive treatment of Cu(II)-EDTA. The recovery of copper, the reuse of $TiO_2$ and the assessment of acute toxicity was studied in the total eight successive photocatalytic reactions. Aqueous solution of $10^{-4}\;M$ Cu(II)-EDTA was treated using an illuminated $TiO_2$ at pH 6 in a circulating reactor. Two different procedures were applied in the reuse of $TiO_2$: i) recycle of $TiO_2$ without acid wash ii) regeneration of $TiO_2$ with acid wash to remove adsorbed copper in a previous experiment. The averaged decomplexation rate constant($k'_{obs}$) of Cu(II)-EDTA in recycle of $TiO_2$ without acid wash was approximately 45% less than that in regeneration of $TiO_2$ with acid wash. Removal of Cu(II) was near complete after 180 minutes in the total eight successive photocatalytic reactions using the regenerated $TiO_2$ after acid wash. In contrast, removal of Cu(II) was minimum at total fifth successive photocatalytic oxidation using the recycled $TiO_2$ without arid wash. The recovered $TiO_2$ was approximately 86% in average in each procedure. The recovered Cu(II) was 67.9% in average. The acute relative toxicity of the treated water rapidly declined at an initial reaction time up to 60 minutes but little declination was observed after 60 minutes due to little degradation of DOC. Relative toxicity of treated water using the recycled $TiO_2$ without acid wash we some what well correlated with the concentration of dissolved Cu(II). From this work, it is suggested that Cu(II)-EDTA can be effectively treated using an integrated cyclic photocatalytic oxidation with recovery of $TiO_2$ and Cu(II).

• Journal of Korean Society of Transportation
• /
• v.33 no.4
• /
• pp.379-392
• /
• 2015

Freight flow data in Korea has been collected for a variety of purposes by various organizations. However, since the representation and format of the data varies, it has not been substantially used for freight analyses and furthermore for freight policies. In order to increase the applicability of those data sets, it is required to bring them in a table and compare for finding the differences. Then, it is shown that the raw data can be aggregated by a particular criterion such as mode, origin and destination, and type commodity. This study aims to examine the freight data issue in terms of three different points of view. First, we investigated various freight volume data sets which are released by several organizations. Second, we tried to develop formulations for freight volume data. Third, we discussed how to apply the formulations to network models in which particular OR (Operations Research) techniques are used. The results emphasized that some data might be useless for modeling once they are aggregated. As a result of examining the freight volume data, this study found that 14 organizations share their data sets at various aggregation levels. This study is not an ordinary research article, which normally includes data analysis, because it seems to be impossible to conduct extensive case studies. The reason is that the data dealt in this study are diverse. Nevertheless, this study might guide the research direction in the freight transport research society in terms of data issue. Especially, it can be concluded that this study is a timely research because the governmemt has emphasized the importance of sharing data to public throughout 'government 3.0' for research purpose.

• Pediatric Infection and Vaccine
• /
• v.11 no.1
• /
• pp.59-72
• /
• 2004

Purpose : Rotaviruses are the major cause of gastroenteritis in infants and young children worldwide. It is important to get the epidemiologic data of rotavirus genotype for the application of rotavirus vaccine. So we tried to investigate the distribution of rotavirus genotypes with RT-PCR. Methods : A total of 120 rotavirus latex agglutinin test positive stool samples were collected continually from 120 children from Sep. 2000 to Apr. 2001. Rotavirus P(VP4), G (VP7) genotypes were determined by RT-PCR. Results : The genotype was identified in 116 stool samples of total 120 samples(96%). The incidence of G genotype was as follow; G1 17(14.2%), G2 74(61.7%), G4 1(0.8%), G9 1(0.8%). There were four cases of multiple genotypes; G1/G2, G1/G4, G1/G9, G8/G9 and genotype of G3, G8 were not found. Twenty three(19.2%) samples were nontypeable. The incidence of P was as follow; P[4] 77(64.2%), P[6] 22(18.3%), P4/P6 12(10%), P[4]/P[8] 1(0.8%) p[8] 1(0.8%). Seven(5.9%) samples were nontypeable. Conclusion : Various combinations of G and P genotypes were observed. Most rotavirus strains were P[4]G2 62(51.74%), followed by P[6]G2 7(5.8%), and P[6]G1 7(5.8%), P[4/P[6] G1 4(3%), P[4]/P[6]G2 4(3%), P[4]G1 3(2.5%), P[8]G2 1(0.8%), P[4]G4 1(0.8%) in Kyoungsangnamdo, Korea during 2000~2001.

• Horticultural Science & Technology
• /
• v.29 no.3
• /
• pp.165-171
• /
• 2011

Plant growth retardants reduce the plant height by inhibiting stem elongation in Lilium davuricum. To investigate the plant hormones related to stem elongation, we sprayed 50 $mg{\cdot}L^{-1}$ diniconazole to young plants of L. davuricum and quantified the contents of endogenous gibberellic acids (GA) and abscisic acid (ABA). In GA biosynthesis, L. davuricum had not only the early C-13 hydroxylation ($GA_{19}{\rightarrow}GA_{20}{\rightarrow}GA_1$) pathway resulting in $GA_1$ as the active form but also the non C-13 hydroxylation (NCH, $GA_{12}{\rightarrow}GA_{24}{\rightarrow}GA_9{\rightarrow}GA_4$) with $GA_4$ as the active form. However, the main pathway was NCH because $GA_4$ concentration of 55 $ng{\cdot}g^{-1}$ dry wt was much higher than $GA_1$ content of 0.23 $ng{\cdot}g^{-1}$ dry wt in control plant. Diniconazole inhibited GA biosynthesis through NCH pathway from its early stage. $GA_{12}$ content decreased by diniconazole up to 6% level of that of control and this effect continued to $GA_4$. Diniconazole reduced $GA_{12}$ content by 12.7 $ng{\cdot}g^{-1}$ dry wt, whereas that of control plant was 213.8 $ng{\cdot}g^{-1}$ dry wt. ABA content decreased up to one third of control by diniconazole application. From the contents of endogenous $GA_4$, $GA_1$, and ABA in this study, we could conclude that diniconazole reduces the plant height by inhibiting $GA_4$ biosynthesis in L. davuricum.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.32 no.2
• /
• pp.312-320
• /
• 2005

The purpose of this study was to evaluate the polymerization contraction and the microhardness of compostie resin($Supreme^{(R)}$, Filtek $Flow^{(R)}$, 3M-ESPE, USA) according to irradiation modes of LED curing unit(Elipar $Freelight^{(R)}$, 3M-ESPE, USA). The strain guage method was used for determination of polymerization contraction. Sample were divided by 6 groups according to curing modes and filling method. Group A: $Supreme^{(R)}$, Filtek $Flow^{(R)}$ lining, 10seconds curing, Group B: $Supreme^{(R)}$, Filtek $Flow^{(R)}$ lining, 15seconds curing, Group C: $Supreme^{(R)}$, Filtek $Flow^{(R)}$ lining, 15seconds soft start curing, Group D: $Supreme^{(R)}$ only, 10seconds curing, Group E: $Supreme^{(R)}$ only, 15seconds curing, Group F: $Supreme^{(R)}$ only, 15seconds soft start curing. Preparations of acrylic molds were followed by filling and curing. Strain guage attached to each sample were connected to a strainmeter. Measurements were recorded at each second for the total of 10 minutes including the periods of light application. And microhardness of each group after 24hours from light irradiation were measured. Obtained data were analyzed statistically using Repeated measures ANOVA and Tukey test. The results of the present study are as follows: 1. In flowable resin liner group, soft start curing group was not found decrease of polymerization contraction. But, In Supreme only filling group, the lowest polymeriation contraction was found in soft start curing group. 2. 10 seconds curing group showed statistically significant reduction of polymerization contraction compared with 15 seconds curing group(p<0.05). 3. The microhardness values of each group not revealed significant difference(p>0.05). But, lower surface microhardness was not reached 80% of upper surface microhardness.

• The Korean Journal of Air & Space Law and Policy
• /
• v.30 no.2
• /
• pp.279-310
• /
• 2015

The Montreal Convention is an agreement that governs the liability of air carriers for injury and death to passengers travelling internationally by air. The Montreal Convention serves as the exclusive legal framework for victims and survivors seeking compensation for injuries or death arising from accidents involving international air travel. The Montreal Convention sets monetary liability caps on damages in order to promote the financial stability of the international airline transport industry and protect the industry from exorbitant damages awards in courts that would inevitably bankrupt an airline. The Convention allows a litigant suing under the Convention to avoid the liability caps in instances where the airline's culpability for the injury or death is the direct result of negligence, another wrongful act, or an omission of the airline or its agents. The Montreal Convention identifies specific locations as appropriate venues to advance claims for litigants seeking compensation. These venues are closely tied to either the carrier's business operations or the passenger's domicile. In March 2015, in an act of suicide stemming from reactive depression, the co-pilot of Germanwings flight 9525 intentionally crashed the aircraft into the French Alps killing the passengers and the remaining crew. Subsequent to the crash, there were media reports that Lufthansa made varying settlement offers to families of the passengers who died aboard the flight ranging from $8,300 USD to $4.5 Million USD depending on the passengers' citizenship. The unverified offers by Lufthansa prompted outcries from the families of the decedent passengers that they would institute suit against the airline in a more plaintiff friendly jurisdiction such as the United States. The first part of this article accomplishes two goals. First, it examines the Montreal Convention's venue requirement along with an overview of the recoverable damages from countries comprising the citizenship of the passengers who were not American. The intentional crash of Germanwings flight 9525 by its First Officer encompasses the possibility that Lufthansa may be exposed to unlimited compensatory damages beyond the liability caps contained in the Convention. The second part of this article explores the application of the Convention's liability limits to the Germanwings flight to demonstrate that the likelihood of escaping the liability limits is slim.

• Journal of dental hygiene science
• /
• v.16 no.2
• /
• pp.176-182
• /
• 2016

The purpose of this study was to evaluate the in-vitro efficacy of the active ingredients of dentifrice following treatment time. The whitening effect was evaluated by a change in lightness value relative to the contact time of hydrogen peroxide, by using artificially stained hydroxyapatite discs. The anti-calculus effect was assessed based on the amount of calcium eluted from the human dental calculus by sodium pyrophosphate. Remineralization was evaluated by the Vickers hardness test following the application of sodium fluoride to bovine enamel. In order to view dentinal tubules occlusion, the formation of insoluble calcium salts by bovine dentin specimens was observed using scanning electron microscopy. Change in lightness value (${\Delta}L$) was $5.50{\pm}1.51$ after 1 min of treatment, $5.73{\pm}0.43$ after 3 min, $8.64{\pm}0.24$ after 10 min, $18.93{\pm}0.76$ after 30 min, and $27.35{\pm}0.54$ after 60 min. The amount of calcium eluted from the human dental calculus was $4.23{\pm}0.14ppm$ after 1 min of treatment, $4.51{\pm}0.04ppm$ after 3 min, $12.12{\pm}0.16ppm$ after 10 min, $17.85{\pm}0.81ppm$ after 30 min, and $25.15{\pm}0.32ppm$ after 60 min. The Vickers hardness change value (${\Delta}VHN$) was $1.96{\pm}1.44$ after 1 min, $1.52{\pm}1.06$ after 3 min, $9.06{\pm}0.15$ after 10 min, $10.83{\pm}5.13$ after 30 min, and $12.55{\pm}2.09$ after 60 min. Partial dentinal tubules occlusion was observed at 10 min and complete occlusion was evident at 60 min. In summary, the use of patch type dentifrices for 10, 30, or 60 min were 1.57 to 8.26 times more effective than using the paste type dentifrices for 1 to 3 min. Based on these findings, it is reasonable to expect that the use of patch type dentifrices for 10 min would lead to remineralization, anti-calculus and dentinal tubules occlusion effects, and that use for 30 min would result in a whitening effect.

• Journal of Korean Society of Forest Science
• /
• v.109 no.3
• /
• pp.271-280
• /
• 2020

This study compared soil CO₂ efflux rates after fertilization, in Pinus densiflora and Quercus variabilis stands. Compound fertilizers were applied to the forest floor in March 2016, following a one-year calibration period (from March 2015 to February 2016). In situ soil CO₂ efflux rates were measured every month during the two-year study periods, using an infrared gas analyzer with a closed chamber system. Mean annual soil CO₂ efflux rates were higher following fertilizer application in the P. densiflora and Q. variabilis stands (P. densiflora: 2.180 μmol m^-2 s^-1; Q. variabilis: 1.977 μmol m^-2 s^-1) as compared with the rates measured during the calibration period (P. densiflora: 1.620 μmol m^-2 s^-1; Q. variabilis: 1.557 μmol m^-2 s^-1). The mean annual soil CO₂ efflux rates in the unfertilized treatments of both stands were not significantly different between the two-year study periods. The Q₁₀ values of fertilized treatments in Q. variabilis stands were higher in the fertilization period (3.41) than in the calibration period (3.14), whereas the Q₁₀ values in P. densiflora stands did not change between the fertilization and calibration periods. The Q₁₀ values of unfertilized treatments in the Q. variabilis stands were lower during the 2016-2017 period (3.69), than in the 2015-2016 period (3.85), whereas the Q₁₀ values in P. densiflora stands were higher during the 2016-2017 period (3.65), than in the 2015-2016 period (3.15). These results indicate that the increase in soil CO₂ efflux rates in P. densiflora stands could be more sensitive to fertilization compared with the rates in Q. variabilis stands.

• Korean Chemical Engineering Research
• /
• v.55 no.2
• /
• pp.242-246
• /
• 2017

The application of composite cathode materials including $LiFePO_4$ (lithium iron phosphate) of olivine crystal structure, which has high thermal stability, were investigated as alternatives for hybrid battery-capacitors with a $LiMn_2O_4$ (spinel crystal structure) cathode, which exhibits decreased performance at high temperatures due to Mn-dissolution. However, these composite cathode materials have been shown to have a reduction in capacity by conducting life cycle experiments in which a $LiFePO_4$/activated carbon cell was charged and discharged between 1.0 V and 2.3 V at two temperatures, $25^{\circ}C$ and $60^{\circ}C$, which caused a degradation of the anode due to the lowered voltage in the anode. To avoid the degradation of the anode, composite cathodes of $LiFePO_4/LiMn_2O_4$ (50:50 wt%), $LiFePO_4$/activated carbon (50:50 wt%) and $LiNi_{1/3}Co_{1/3}Mn_{1/3}O_2$ (50:50 wt%) were prepared and the life cycle experiments were conducted on these cells. The composite cathode including $LiNi_{1/3}Co_{1/3}Mn_{1/3}O_2$ of layered crystal structure showed stable voltage behavior. The discharge capacity retention ratio of $LiNi_{1/3}Co_{1/3}Mn_{1/3}O_2$ was about twice as high as that of a $LiFePO_4/LiMn_2O_4$ cell at thermal stability experiment for a duration of 1,000 hours charged at 2.3 V and a temperature of $80^{\circ}C$.