• Korean Journal of Metals and Materials
• /
• v.48 no.5
• /
• pp.449-455
• /
• 2010

To enhance the efficiency of dye sensitized solar cells, we proposed crystalline anatase-$TiO_{2}$ by using a low temperature process ($150^{\circ}C{\sim}250^{\circ}C$). We successfully fabricated 30 nm-$TiO_{2}$ at a fixed atomic layer deposition condition of 1.0 sec of TDMAT pulse, 20 sec of TDMAT purge, 0.5 sec of H$_{2}$O pulse, and 20 sec of H$_{2}$O purge. In order to examine the microstructure, phase, and band-gap of the TiO$_{2}$ respectively, we employed a Nano-Spec, transmission electron microscope, high resolution XRD, Auger electron spectroscopy, scanning probe microscope, and UV-VIS-NIR. We were able to fabricate a crystalline anatase-phase of 30 nm-TiO$_{2}$ successfully at temperatures above $180^{\circ}C$. Our results showed that our proposed low temperature ALD process (below $200^{\circ}C$) might be applicable to glass and flexible polymer substrates.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.4
• /
• pp.173-177
• /
• 2010

Thermal stabilizing effect of $Yb^{3+},\;Er^{3+}$ codoping into $TiO_2$ powder prepared by sol-gel method and its upconversion characteristics were analyzed. The effect of $TiO_2:Yb^{3+},\;Er^{3+}$ ions on crystallinity and phase transition was studied by X-ray diffraction (XRD). The change of band-gap energy induced from Yb and Er codoping was analyzed by UV-Vis. The band-gap energy of $TiO_2$ have been slightly narrowed by $Yb^{3+},\;Er^{3+}$ codoping, which indicated that the $Yb^{3+},\;Er^{3+}$ ions can enhance the photo-catalytic property of $TiO_2$. green and red up-conversions of $Yb^{3+}$ and $Er^{3+}$ co-doped $Y_2O_3:Yb^{3+},\;Er^{3+}$ phosphor were analyzed by PL equipped with 980 nm laser.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.2
• /
• pp.402-404
• /
• 2009

The band structures and the densities of states at the Fermi energy for rutile, anatase and brookite phases are investigated along with the structure-photocatlaytic relationship by using DFT method. Bands are less dispersive in anatase phase than in rutile phase, and they are almost flat in brookite phase. As a result, the DOS value near the Fermi energy for brookite is highest among three types of $TiO_{2}$, which means that the numbers of electrons near the Fermi energy are largest in brookite. The calculation shows that brookite phase may exhibit highest photocatalytic efficiency among three types of $TiO_{2}$.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.11
• /
• pp.3767-3771
• /
• 2012

In this study, we investigate the potential use of $TiO_2@SiO_2$ and $ZnO@SiO_2$ core/shell nanoparticles (NPs) as effective UV shielding agent. In the typical synthesis, $SiO_2$ was coated over different types of $TiO_2$ (anatase and rutile) and ZnO by sol-gel method. The synthesized $TiO_2@SiO_2$ and $ZnO@SiO_2$ NPs were characterized by UV-Vis, XRD, SEM and TEM. The UV-vis absorbance and transmittance spectra of core@shell NPs showed an efficient blocking effect in the UV region and more than 90% transmittance in the visible region. XRD and SAED studies confirmed the formation of amorphous $SiO_2$ coated over the $TiO_2$ and ZnO NPs. The FESEM and TEM images shows that coating of $SiO_2$ over the surface of anatase, rutile $TiO_2$ and ZnO NPs resulted in the increase in particle size by ~30 nm. In order to study the UV light shielding capability of the samples, photocatalytic degradation of methylene blue dye on $TiO_2@SiO_2$ and $ZnO@SiO_2$ NPs was performed. Photocatalytic activity for both types of $TiO_2$ NPs was partially suppressed. In comparison, the photocatalytic activity of ZnO almost vanished after the $SiO_2$ coating.

• Journal of the Korean Ceramic Society
• /
• v.45 no.1
• /
• pp.36-42
• /
• 2008

Carbon/$TiO_2$ composite photocatalysts were thermally synthesized with different mixing ratios of anatase to phenol resin through an ethanol solvent dissolving method. The XRD patterns revealed that only anatase phase can be identified for Carbon/$TiO_2$ composites. The diffraction peaks of carbon were not observed, however, due to the low carbon content on the $TiO_2$ surfaces and the low crystallinity of amorphous carbon. The results of chemical elemental analyses of the Carbon/$TiO_2$ composites showed that most of the spectra for these samples gave stronger peaks for carbon and Ti metal than that of any other elements. The BET surface area increases to the maximum value of $488\;m^2/g$ with the area depending on the amount of phenol resin. From the SEM images, small $TiO_2$ particles were homogeneously distributed to a composite cluster with the porosity of phenol resin-based carbon. From the photocatalytic results, the MB degradation should be attributed to the three kinds of synergetic effects, such as photocatalysis, adsorptivity, and electron transfer by light absorption between supporter $TiO_2$ and carbon.

• Journal of the Korean Ceramic Society
• /
• v.35 no.10
• /
• pp.1049-1054
• /
• 1998

In order to fabricate ideal powders new processing is necessary in which the solute atoms in solution ra-pidly move to mix each other to the degree of molecular level the viscosity of solution should be low not to effect the moving of solute atoms and the powders could be directly obtained as crystalline. Supercritical fluid is defined as condensed gas sated up to its critical pressure and temperature. In this paper su-percritical fluid methods were studied as a new ceramic processing of powder preparation. The crystalline powders of TiO2 which are useful for electronic ceramic materials were fabricated by hydrolysis of titanium (IV) ethoxide using ethanol as a supercritical fluid at the condition of 270$\pm$3$^{\circ}C$, 7.3 MPa for 2hr. The cry stalline anatase powders could be directly obtained and its primary particle size was 20 min.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.9
• /
• pp.1341-1345
• /
• 2004

We developed a novel synthesis strategy of titania nanowire arrays by employing simple hydrothermal reaction and ion-exchange reaction techniques. Hydrothermal reactions of metallic titanium powder with $H_2O_2$ in a 10 M NaOH solution produced a new sodium titanate compound, $Na_2Ti_6O_{13}{\cdot}xH_2O$ (x~4.2), as arrays of nanowires of lengths up to 1 mm. Acid-treatment followed by calcination of this material produced arrays of highly crystalline anatase nanowires as evidenced by x-ray diffraction, Raman spectroscopy, and transmission electron microscopy studies. In both cases of sodium titanate and anatase, the nanowires have exceptionally large aspect ratios of 10,000 or higher, and they form arrays over a large area of $1.5 {\times} 3 cm^2$. Observations on the reaction products with varied conditions indicate that the array formation requires simultaneously controlled formation and crystal growth rates of the $Na_2Ti_6O_{13}{\cdot}xH_2O$ phase.

• Journal of the Korean Ceramic Society
• /
• v.35 no.6
• /
• pp.594-602
• /
• 1998

Titanium hydroxide (TiO({{{{ {OH }_{2 } }})) fine particles were produced by the reverse micelle technique. For the formation of titanium hydroxide (TiO({{{{ {OH }_{2 } }})) particles with the technique reversed micellar solution was prepared by solubilizing water into organic solvent (isooctane) with a surfactant and titanium alkoxide (tetraisopropyl orthotitanate) diluted with isopropyl alcohol was added to the reversed micellar solution. The hdrolyzed species (TiO({{{{ {OH }_{2 } }})) was formed by the hydrolysis of titanium alkoxide and titanium dioxide is then formed by the condensation of the hydrolyzed species. There are several process variables such as surfactants concentration of surface cosurfactant hydrolysis temperature and pH. In this work the ef-fects of process variables on paticle shapes particle size distribution and paticle agglomeration were bi-nodal for an anionic surfactant(AOT) in the whole range of temperature pH and surfactant concentration of this experiment. The addition of ethanol as a cosurfactant resulted in narrow particle size distribution of the experiment. The additiono of ethanol as a cosurfactant resulted in narrow particle size distribution and 0.12${\mu}{\textrm}{m}$ of smaller average particle diameter. FT-IR spectrum of particles shows the absorption peak of Ti-OH bonding and Ti-O bonding. An exothermic peak around 41$0^{\circ}C$ in TGA-DTA curve shows that crys- tallized anatase phase appears and completely transits to anatase around 45$0^{\circ}C$.

• Korean Journal of Materials Research
• /
• v.22 no.5
• /
• pp.249-252
• /
• 2012

Fe doped $TiO_2$ nanoparticles were prepared under high temperature and pressure conditions by mixture of metal nitrate solution and $TiO_2$ sol. Fe doped $TiO_2$ particles were reacted in the temperature range of 170 to $200^{\circ}C$ for 6 h. The microstructure and phase of the synthesized Fe doped $TiO_2$ nanoparticles were studied by SEM (FE-SEM), TEM, and XRD. Thermal properties of the synthesized Fe doped $TiO_2$ nanoparticles were studied by TG-DTA analysis. TEM and X-ray diffraction pattern shows that the synthesized Fe doped $TiO_2$ nanoparticles were crystalline. The average size and distribution of the synthesized Fe doped $TiO_2$ nanoparticles were about 10 nm and narrow, respectively. The average size of the synthesized Fe doped $TiO_2$ nanoparticles increased as the reaction temperature increased. The overall reduction in weight of Fe doped $TiO_2$ nanoparticles was about 16% up to ${\sim}700^{\circ}C$; water of crystallization was dehydrated at $271^{\circ}C$. The transition of Fe doped $TiO_2$ nanoparticle phase from anatase to rutile occurred at almost $561^{\circ}C$. The amount of rutile phase of the synthesized Fe doped $TiO_2$ nanoparticles increased with decreasing Fe concentration. The effects of synthesis parameters, such as the concentration of the starting solution and the reaction temperature, are discussed.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.6
• /
• pp.1989-1992
• /
• 2012

We present a low temperature (${\approx}70^{\circ}C$) method to prepare anatase, vertically aligned feather-like $TiO_2$ (VAFT) nanowire arrays $via$ reactive pulsed DC magnetron sputtering. The synthesis method is general, offering a promising strategy for preparing crystalline nanowire metal oxide films for applications including gas sensing, photocatalysis, and 3rd generation photovoltaics. As an example application, anatase nanowire films are grown on fluorine doped tin oxide coated glass substrates and used as the photoanode in dye sensitized solar cells (DSSCs). AM1.5G power conversion efficiencies for the solar cells made of 1 ${\mu}m$ thick VAFT have reached 0.42%, which compares favorably to solar cells made of the same thickness P25 $TiO_2$ (0.35%).