• Journal of Environmental Science International
• /
• v.18 no.8
• /
• pp.927-932
• /
• 2009

Wind turbine noise become main environmental problem as wind energy have been installed all around. Noise from large wind turbine give annoyance to listener, moreover it increase loading to whole system by restricting blade tip speed. However accurate noise mechanism of wind turbine is not yet examined. This paper reviewed noise source and analysis theory. Broadband noise if main component of wind turbine noise and airfoil self noise is main noise source. These make acoustic analogy hard to apply for analysis. For this reason, experimental equation is method for wind turbine noise prediction up to now. Spectrum analysis shows that vortex shedding noise exists around $1k{\sim}2k$ Hz. This region is most sensitive frequency range to human. Thus it is necessary to reduce this noise source.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.11 s.116
• /
• pp.1165-1171
• /
• 2006

This paper presents a new type of jetting dispenser for the integrated circuit (IC) fabrication and surface mount technology The proposed system is featured by the piezoelectric actuator and hydraulic magnification device. After describing structural component of the dispensing mechanism and its operation principle, both the fluid modeling and the hydraulic magnification modeling are undertaken with a lumped-parameter method based on the analogy of the fluid system and mechanical system. A mathematical governing equation is then derived by integrating the fluid model with the mechanical model of the driving piston and piezoelectric actuator. Subsequently, in order to achieve a desired dispensing amount, control algorithm adjusting duty cycle of the driving voltage is synthesized and control responses are presented in time domain.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.428-433
• /
• 2006

This paper presents a new type of jetting dispenser for the integrated circuit(IC) fabrication and surface mount technology. The proposed system is featured by the piezoelectric actuator and hydraulic magnification device. After describing structural component of the dispensing mechanism and its operation principle, both the fluid modeling and the hydraulic magnification modeling are undertaken with a lumped-parameter method based on the analogy of the fluid system and mechanical system. A mathematical governing equation is then derived by integrating the fluid model with the mechanical model of the driving piston and piezoelectric actuator. Subsequently, in order to achieve a desired dispensing amount, control algorithm adjusting duty cycle of the driving voltage is synthesized and control responses are presented in time domain.

• Water for future
• /
• v.12 no.1
• /
• pp.56-59
• /
• 1979

A prompt subsurface runoff producing mechanism whih creaters a depletion curve of direct runoff hydrograph is simulated by a dead zone dispersion model technique. Runoff processes are carried out by routing of the outflow resulted from previous linear channel and effective rainfall from its corresponding subwatershed through a series of conceptual linear channels representing subwatersheds of a catchment. Working rules are explained for evaluation the model parameters such as translatory velocity, diffusive factor, and parameters concerning the infiltration and relative magnitude of the prompt subsurface flow region.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.847-847
• /
• 2004

Automobile cooling fans are operated with a radiator module. To design low noise, high performance cooling fan, radiator resistance should be considered in the design process. The system (radiator) resistance reduces axial velocity and increases effective angle of attack. This increasing effective angle of attack mechanism causes blade stall, performance decrease and noise increase. In this paper, To analyze fan performance, freewake and 3D CFD calculations are used To design high performance fan with consideration of system resistance, optimal twist concept is applied through momentum and blade element theory. To predict fan noise, empirical formula and acoustic analogy methods are used.

• 중국학논총
• /
• no.71
• /
• pp.41-59
• /
• 2021

With the progress of social economy and science and technology, network media technology has developed rapidly, China has ushered in the network information age, and the network buzzwords emerged to reflect the interaction and influence between language and society. The network buzzwords of "X+ ren "indirectly show the social psychology and value orientation of modern people with their unique structural characteristics, semantic connotation and cultural deposits, and so on. Based on this, we have conducted a multi-angle investigation on the network buzzwords "X+ ren". This paper first analyzes the structure types and syntactic functions of the lexical model of "X+ ren ", then makes a semantic analysis of the lexical model of "X+ Ren ", and finally investigates the causes and influences of the popularity of "X+ ren ". Through the investigation, we believe that "X+ ren "will continue to grow, and "X+ ren" will continue to attract the attention of the academic community.

• Journal of KSNVE
• /
• v.9 no.5
• /
• pp.955-965
• /
• 1999

Centrifugal fans are widely used and the noise generated by the these machines causes one of the most serious problems. In general, the centrifugal fan noise is often dominated by tones at BPF(blade passage frequency) and its higher harmonics. This is a consequence of the strong interaction between the flow discharged form the impeller and the cutoff in the casing. However, only a few researches have been carried out on predicting the noise because of the difficulty in obtaining detailed information about the flow field and casing effects on noise radiation. The objective of this study is to understand the generation mechanism of sound and to develop a prediction method for the unsteady flow field and the acoustic pressure field of a centrifugal fan. We assume that the impeller rotates with a constant angular velocity and the flow field of the impeller is incompressible and inviscid. So, a discrete vortex method (DVM) is used to model the centrifugal by the unsteady Bernoulli equation. Lowson's method is used to predict the acoustic source. A centrifugal impeller and wedge introduced by Weidemann are used in the numerical calculation and the results are compared with the experimental data. Reasonable results are obtained not only for the peak frequencies but also for the amplitudes of the tonal sound.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.9
• /
• pp.1165-1174
• /
• 2001

The objective of this study is to understand the generation mechanism of sound and to develop a prediction method for the acoustic pressure field of a centrifugal fan. If the fan is operating at the free field without the casing, the acoustic analogy is a good method to predict the acoustic of the fan. But, the casing gives a dominant effect to the radiated sound field and the scattering effect of casing should be considered. So, in this paper the Kirchhoff-BEM is developed, which can consider the scattering effect of the rigid body. In order to consider the scattering and diffraction effects owing to the casing, BEM is introduced. The source of BEM is newly developed, so the sound field of the centrifugal fan can be obtained. In order to compare the predicted one with experimental data, a centrifugal impeller and a wedge are used in the numerical calculation and the results are compared with the experimental data. Reasonable results are obtained not only for the peak frequencies but also for the amplitudes of the tonal sound. The radiated acoustic field shows the diffraction and scattering effects of the wedge clearly.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1285-1289
• /
• 2006

In a large diameter piping system, high frequency energy can produce excessive noise, high vibration, and failures of thermo-well, instrumentation, and attached small-bore piping. High frequency energy is generated by flow induced vibration like vortex shedding in orifices and valves. Once this energy is generated, amplification may occur from acoustical and/or structural resonances, resulting in high amplitude vibration and noise. At low frequencies, pipe vibration occurs laterally along the pipe's length, but at higher frequencies, the pipe shell wall vibrates radially across its cross-section. The simple beam analogy which is based on the beam mode vibration can not be applied to evaluate shell mode vibration. ASME OM3 recommends that the stress be measured directly by strain gauge and be evaluated according to the fatigue curves of the piping material. This Paper discusses the excitation and amplification mechanism relevant to high frequency energy generation in piping system, the monitoring method of the shell mode vibration in ASME OM3, the evaluation method generally used in the industry. Finally this paper presents the stress evaluation of the cavitating venturi down stream piping, where high frequency shell mode vibrations were observed during the operation.

• Archives of design research
• /
• v.15 no.4
• /
• pp.139-148
• /
• 2002

This study deals with the occurrence and application of 'Fun' as a linguistic function through form-giving. As a linguistic function, Fun could be defined, in a broad sense, as an emotion of desire when in relation to artifacts, and, in a narrow sense, as a physical or mental response when a person discovers unexpected information or artifacts. Hence, the occurrence of 'Fun' could be an analogy of a removal of a 'mental block' from using (or perceiving) artifacts. As an aspect of cognitive psychology, the context of form-giving, which has meanings in both artifact and design activity, will deal with an important factor of form-giving. From that, the elements of the context and the transformation of the elements are suggestive of 'Fun-oriented form-giving'. Hence, this study will show how to deal with that elements, what is required condition on it, 'Fun' in form-giving, and the Mechanism of Occurrence of 'FUN' based on this study, will be expected to apply them for product-concept effectively and Form-Giving fashionably.