• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.9
• /
• pp.677-680
• /
• 2012

The dependency of annealing temperature on the electrical performances in amorphous silicon-zinc-tin-oxide thin film transistors (SZTO-TFT) has been investigated. The SZTO channel layers were prepared by using radio frequency (RF) magnetron sputtering method with different annealing treatment. The field effect mobility (${\mu}_{FE}$) increased and threshold voltage ($V_{th}$) shifted to negative direction with increasing annealing temperature. As a result, oxygen vacancies generated in SZTO channel layer with increasing annealing temperature resulted in negative shift in $V_{th}$ and increase in on-current.

• Journal of Magnetics
• /
• v.9 no.2
• /
• pp.47-51
• /
• 2004

Giant magneto-impedance (GMI) effect in zero-magnetostrictive Co-based amorphous ribbons samples in their as-quenched and stress-released states as well as with intentionally induced magnetic anisotropy were investigated. Magnetic and impedance properties of the samples exhibiting different anisotropy were compared and the optimum operation conditions for the studied samples from the view-point of their utilization as a sensor element have been determined. A design of a model of magnetic field sensor and characteristics of the constructed prototype are presented.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.57-59
• /
• 1994

The transformer core using amorphous Fe-B-Si ribbon were designed by magnetostatic software. The basic model of core is Butt-Lap-Step type, non-culled typo and stair type core joint. And the variables are the number of ribbons for on step, flux density and core shape.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2002.12a
• /
• pp.208-209
• /
• 2002

Recently an asymmetric giant magnetoimpedance (GMI) profile has been observed in Co-based amorphous ribbons annealed at the weak field [1-4]. This phenomenon has attracted a large interest due to its practical application to sensitive magnetic sensors. It is known [5.6] that in magnetic materials, the magnetoimpedance is caused by the effect of the magnetic field on the transverse magnetic permeability of a near-surface layer. In consequence of it, the value of the magnetoimpedance depends strongly on near-surface magnetic properties of the sample. (omitted)

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.597-600
• /
• 1995

The effects of surface oxidation on magnetic properties were investigated at high frequencies (10k-100MHz) for $7-18\mu\textrm{m}$ thick $Co_{70}Fe_{5}Si_{15}B_{10}$ amorphous ribbons with controlled domain structure. Oxidation was accelerated by acid-treatment or anodic oxidation treatment, and the insulation layers were prepared on the surfaces of the ribbons. The acid-treatment was effective in improving permeability and magnetic loss. Although the anodic oxidation treatment was effective in both making oxide layer and thinning, the magnetic properties were not improved compared with the case of the acid-treatment.

• Journal of Electrochemical Science and Technology
• /
• v.10 no.1
• /
• pp.82-88
• /
• 2019

Here, we report on nanocrystalline Si-Al-M (M = Fe, Cu, Ni, Zr) alloys for use as an anode for lithium-ion batteries, which were fabricated via a melt-spinning method. Based on the XRD and TEM analyses, it was found that the Si-Al-M alloys consist of nanocrystalline Si grains surrounded by an amorphous matrix phase. Among the Si-Al-M alloys with different metal composition, Ni-incorporated Si-Al-M alloy electrode retained the high discharge capacity of 2492 mAh/g and exhibited improved cyclability. The superior $Li^+$ storage performance of Si-Al-M alloy with Ni component is mainly responsible for the incorporated Ni, which induces the formation of ductile and conductive inactive matrix with crystalline Al phase, in addition to the grain size reduction of active Si phase.

• Advanced Composite Materials
• /
• v.18 no.4
• /
• pp.339-350
• /
• 2009

Al-Fe-V-Si alloys reinforced with SiC particles were prepared by multi-layer spray deposition technique. Both microstructures and mechanical properties including hardness and tensile properties development during hot exposure process of Al-8.5Fe-1.3V-1.7Si, Al-8.5Fe-1.3V-1.7Si/15 vol% $SiC_P$ and Al-10.0Fe-1.3V-2Si/15 vol% $SiC_P$ were investigated. The experimental results showed that an amorphous interface of about 3 nm in thickness formed between SiC particles and the matrix. SiC particles injected silicon into the matrix; thus an elevated silicon concentration was found around $\alpha-Al_{12}(Fe,\;V)_3Si$ dispersoids, which subsequently inhibited the coarsening and decomposition of $\alpha-Al_{12}(Fe,\;V)_3Si$ dispersoids and enhanced the thermostability of the alloy matrix. Moreover, the thermostability of microstructure and mechanical properties of Al-10.0Fe-1.3V-2Si/15 vol% $SiC_P$ are of higher quality than those of Al-8.5Fe-1.3V-1.7Si/15 vol% $SiC_P$.

• Applied Microscopy
• /
• v.47 no.1
• /
• pp.50-54
• /
• 2017

The microstructure, the crystallization behavior, and magnetic properties of FeSi-based soft magnetic alloys (FINEMET) were investigated using transmission electron microscopy, X-ray diffraction, and coercive force measurements. The amorphous $Fe_{73.28}Si_{13.43}B_{8.72}Cu_{0.94}Nb_{3.63}$ alloys particles, prepared in $10^{-4}$ torr by gas atomization process, were heat treated at $530^{\circ}C$, $600^{\circ}C$, and $670^{\circ}C$ for 1 hour in a vacuum of $10^{-2}$ torr. Nanocrystalline Fe precipitation was first formed followed by the grain growth. Phase formation and crystallite sizes was compared linked to its magnetic behavior, which showed that excellent soft magnetic property can directly be correlated with its microstructure.

• Carbon letters
• /
• v.13 no.1
• /
• pp.44-47
• /
• 2012

We analyzed the effect of etchants for metal catalysts in terms of the characteristics of resulting graphene films, such as sheet resistance, hall mobility, transmittance, and carrier concentration. We found the residue of $FeCl_3$ etchant degraded the sheet resistance and mobility of graphene films. The residue was identified as an iron oxide containing a small amount of Cl through elemental analysis using X-ray photoelectron spectroscopy. To remove this residue, we provide an alternative etching solution by introducing acidic etching solutions and their combinations ($HNO_3$, HCl, $FeCl_3$ + HCl, and $FeCl_3+HNO_3$). The combination of $FeCl_3$ and acidic solutions (HCl and $HNO_3$) resulted in more enhanced electrical properties than pure etchants, which is attributed to the elimination of left over etching residue, and a small amount of amorphous carbon debris after the etching process.

• Journal of the Korean Magnetics Society
• /
• v.7 no.6
• /
• pp.293-298
• /
• 1997

$Fe_5Si_Xb_{5-x}$ (x=0, 1, 2, 3) powders were prepared by mechanical alloying, and their phases and magnetic properties were investigated by using XRD, TEM, Mossbauer spectroscopy and VSM. Starting elements are incorporated into $\alpha$-Fe in the early stage of mechanical alloying, and the stable phases are formed as the milling proceeds. After the annealing at 80$0^{\circ}C$ for 2 hours, it is found that the FeB and $Fe_2B$ phases coexist for the $Fe_5B_5$(x=0) composition. By substituting Si for B, the formation of $Fe_2B$ phase is restricted and the $Fe_5SiB_2$, $Fe_2Si_{0.4}B_{0.6}$ and paramagnetic phase begin to appear. The FeB phase has wide range of hyperfine magnetic field because it is not fully crystallized on the annealing at 800 $^{\circ}C$. On the contrary, others have good crystalline phases and show well-defined hyperfine magnetic field. Magnetic saturation is highest for the $Fe_5B_5$ composition where the amount of the $Fe_2B$ phase in large.