• Journal of Nutrition and Health
• /
• 제5권2호
• /
• pp.91-103
• /
• 1972

Zinc is one of the essential trace elements in the living organism for growth and health. The first identified metalloenzyme, carbonic anhydrase, is a zinc compound and several others have been described since. Among zinc deficiency syndromes in animals porcine parakeratosis has been successfully treated with zinc supplements, and in man a syndrome of anemia, hypogonadism, hepatosplenomegaly, and dwarfism, prevalent in parts of Iran and Egypt, has been ascribed to lack of zinc in the diet. Dietary zinc excess in the rat is manifested by a hypochromic, microcytic anemia, poor growth, reduction in liver catalase and cytochrome oxidase. The present study is an attempt to delineate the changes of tissue contents of trace elements, especially of iron, copper and zinc in liver and kidneys of the rats. Weanling albino rats, weighing 60 to 80gm. were used in this experiments. The rats were housed in cages with aluminum floors and received feed and distilled water ad libitum. Animals were divided into three groups, control, low zinc diet and high zinc diet groups. The high zinc diet group was subdivided into 0.5% Zn and 0.7%Zn groups. The supplementary copper or iron was added to the high dietary zinc groups. The animals were sacrificed and the tissues were washed several times with deionized water. The wet digested samples were analyzed by Hitachi Model 207 atomic absorption spectro-photometer for the determination of iron, copper and zinc in the liver and kidney. Hemoglobin level in the blood was measured by cyanmethemoglobin method. The results of this study are as follows: 1) All rats fed high zinc diets and low zinc diets gained less weight than control. Weight gain was not improved by the supplementary copper or iron and both. 2) Hemoglobin concentration was decreased significantly in the rats fed high zinc diets and less in the low zinc diet. Supplementary copper and iron to the higher zinc diet appeared to give some improvement of anemia. 3) The iron contents of the liver and kidneys were significantly decreased in the high zinc groups and the reduction was more significantly in the rats receiving higher zinc diet (0.7%). The supplementary copper caused a further depression of liver iron. On the other hand, the iron, added to the high zinc diet lessoned the severity of the decrease in liver iron and caused kidney iron to be maintained almost at the level found in the rats fed by zinc and supplementary copper diet. 4) High zinc diets did not change copper content of the liver and kidney. Supplementary copper elevated the concentration in the liver and kidney and added iron had no effect on the accumulation of copper in the liver and kidneys. 5) The high zinc diets caused marked increases of zinc content in the liver and kidney. Supplementary iron to the high zinc diet caused increases of zinc contents of liver and kidneys.

• 대한화학회지
• /
• 제63권6호
• /
• pp.440-445
• /
• 2019

본 연구는 자동차 폐리튬 이차전지의 모듈로부터 재생할 수 있는 자원을 효율적으로 회수하는 방법을 개발하는 것이다. 모듈의 셀은 구리 박막, 알루미늄 박막, 그리고 이들 사이는 폴리머 재질의 격막으로 이루어져 있다. 셀은 특별히 제작한 글러브 상자 안에서 그리고 여러 번의 단계를 거쳐 손상 없이 완전히 해체 하였다. 우선적으로 양극활물질은 400 ℃에서 열처리하여 알루미늄 박막으로부터 분리하였다. 그런 후 분리된 양극활물질은 잔류되어 있는 탄소 성분을 제거하기 위해 800 ℃에서의 소성 후에 최종적으로 높은 순도로 회수되었다. 본 연구 결과를 바탕으로 해서, 알루미늄 박막으로부터 양극활물질을 구성하고 있는 코발트(Co), 니켈(Ni), 망간(Mn), 리튬(Li)과 같은 희유금속들을 80% 이상 회수할 수 있었다.

• Composites Research
• /
• 제28권5호
• /
• pp.254-259
• /
• 2015

탄소섬유에 대한 액상 알루미늄의 젖음성이 매우 좋지 않기 때문에 통상적인 주조방법으로는 기공이 없는 건전한 탄소섬유/알루미늄 복합재료 제조가 어려워 이를 극복하기 위해서는 복합재료 주조 시 고온, 고압이 요구된다. 본 연구에서는 탄소섬유 표면에 무전해 도금에 의해 구리를 코팅함으로써 탄소섬유에 대한 알루미늄의 젖음성을 향상시켜 고온, 고압을 가하지 않고 액상의 알루미늄이 탄소섬유들 사이를 자발적으로 침투하여 내부기공이 매우 적은 건전한 탄소섬유/알루미늄 복합재료를 제조할 수 있었다. 제조된 탄소섬유/알루미늄 복합재료내 일부 탄소섬유 다발 안에서 미세기공이 발생하였으나 이 미세기공은 압연과 같은 후 가공에 의해 탄소섬유와 알루미늄 사이의 계면분리나 탄소섬유의 파괴 없이 효과적으로 제거될 수 있었다. 복합재료 제조 시 발생한 미세기공은 탄소섬유와 알루미늄의 젖음성 문제는 아니며 탄소섬유들 사이 공간을 효과적으로 채웠던 액상 알루미늄이 냉각되는 동안 수축으로 인해 일부 탄소섬유들 사이로부터 빠져 나가 수축공 형태의 기공이 발생한 것으로 판단된다.

• Journal of Welding and Joining
• /
• 제3권2호
• /
• pp.27-34
• /
• 1985

The mechanical properties and bonding mechanism of aluminum, copper and mild steel have been determined in cold pressure welding. The brittle cover layer to be established by scratch-brushing plays an important role in bond strength and has an influence on the threshold of deformation. The cold pressure welding was achieved at 54% of height reduction in A1-A1, 75% in Cu-Cu, 56% in Al-Cu, and 74% in Cu-steel. The height reduction at which the bond strength of weld interface was the same as the tensile strength of base metal should be over 76% in Al-Al, 82% in Cu-Cu, and 78% in Al-Cu.

• 한국막학회:학술대회논문집
• /
• 한국막학회 1994년도 추계 총회 및 학술발표회
• /
• pp.8-11
• /
• 1994

Disposal of hazardous ions in the aqueous streams is a significant industrial waste problem.. Waste streams from electronics, electroplating, and photographic industries contain metal ions such as copper, nickel, zinc, chromium(IV), cadmium, aluminum, silver, and gold, amongst others in various aqueous solutions such as sulfates, chlorides, fluorocarbons, and cyanides. Typical plating solutions having similar compositions are listed in Table 1. Spent process streams in catalyst manufacturing facilities also contain precious metals such as Ag, Pt, and Pd. Developing an effective recovery process of these metal ions for reuse is important.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.829-830
• /
• 2006

Recent research at Harbin Institute of Technology on the synthesis of nanocrystalline and untrafine grained materials by mechanical alloying/milling is reviewed. Examples of the materials include aluminum alloy, copper alloy, magnesium-based hydrogen storage material, and $Nd_2Fe_{14}B/{\alpha}-Fe$ magnetic nanocomposite. Details of the processes of mechanical alloying and consolidation of the mechanically alloyed nanocrystalline powder materials are presented. The microstructure characteristics and properties of the synthesized materials are addressed.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2001년도 추계학술강연 및 발표대회
• /
• pp.7-7
• /
• 2001

The increasing interest in light weight materials coupled to the need for cost -effective processing have combined to create a significant opportunity for aluminum P/M. particularly in the automotive industry in order to reduce fuel emissions and improve fuel economy at affordable prices. Additional potential markets for Al PIM parts include hand tools. Where moving parts against gravity represents a challenge; and office machinery, where reciprocating forces are important. Aluminum PIM adds light weight, high compressibility. low sintering temperatures. easy machinability and good corrosion resistance to all advantages of conventional iron bm;ed P/rv1. Current commercial alloys are pre-mixed of either the AI-Si-Mg or AL-Cu-Mg-Si type and contain 1.5% ethylene bis-stearamide as an internal lubricant. The powder is compacted in closed dies at pressure of 200-500Mpa and sintered in nitrogen at temperatures between $580~630^{\circ}C$ in continuous muffle furnace. For some applications no further processing is required. although most applications require one or more secondary operations such as sizing and finishing. These sccondary operations improve the dimension. properties or appearance of the finished part. Aluminum is often considered difficult to sinter because of the presence of a stable surface oxide film. Removal of the oxide in iron and copper based is usually achieved through the use of reducing atmospheres. such as hydrogen or dissociated ammonia. In aluminum. this occurs in the solid st,lte through the partial reduction of the aluminum by magncsium to form spinel. This exposcs the underlying metal and facilitates sintering. It has recently been shown that < 0.2% Mg is all that is required. It is noteworthy that most aluminum pre-mixes contain at least 0.5% Mg. The sintering of aluminum alloys can be further enhanced by selective microalloying. Just 100ppm pf tin chnnges the liquid phase sintering kinetics of the 2xxx alloys to produce a tensile strength of 375Mpa. an increilse of nearly 20% over the unmodified alloy. The ductility is unnffected. A similar but different effect occurs by the addition of 100 ppm of Pb to 7xxx alloys. The lend changes the wetting characteristics of the sintering liquid which serves to increase the tensile strength to 440 Mpa. a 40% increase over unmodified aIloys. Current research is predominantly aimed at the development of metal matrix composites. which have a high specific modulus. good wear resistance and a tailorable coefficient of thermal expnnsion. By controlling particle clustering and by engineering the ceramic/matrix interface in order to enhance sintering. very attractive properties can be achicved in the ns-sintered state. I\t an ils-sintered density ilpproaching 99%. these new experimental alloys hnve a modulus of 130 Gpa and an ultimate tensile strength of 212 Mpa in the T4 temper. In contest. unreinforcecl aluminum has a modulus of just 70 Gpa.

• 한국토양비료학회지
• /
• 제49권2호
• /
• pp.200-207
• /
• 2016

To add new groundwater standard, 7 candidate materials (copper, zinc, selenium, manganese, iron, chromium, aluminum) were calculated by CROWN (Chemical Ranking Of groundwater pollutaNts). Copper and zinc were selected as groundwater candidates through the process and monitored total 430 samples for 2 years with 113 groundwater sampling sites. In this study, geological distribution characteristics (igneous rock, metamorphic rock, sedimentary rock) of copper and zinc were evaluated and the geological background levels obtained by a cumulative probability distribution and pre-selection methods were compared. In the results, the highest average concentrations of the copper and zinc were observed both in the igneous rock. The detection concentration ranges of copper and zinc in 430 groundwater samples were $0.002{\sim}0.931mg\;L^{-1}$, and $0.002{\sim}32.293mg\;L^{-1}$, respectively. In addition, detection concentration ranges of copper and zinc were $0.002{\sim}0.931mg\;L^{-1}$, $0.002{\sim}32.293mg\;L^{-1}$ in the igneous rock, $0.002{\sim}0.134mg\;L^{-1}$, $0.004{\sim}7.038mg\;L^{-1}$ in the metamorphic rock and $0.002{\sim}0.008mg\;L^{-1}$, $0.003{\sim}3.948mg\;L^{-1}$ in the sedimentary rock, respectively. As a result of the background concentrations with two methods, zinc concentrations with the pre-selected method are comparatively higher than that of the others with the cumulative distribution.

• Environmental Sciences Bulletin of The Korean Environmental Sciences Society
• /
• 제2권2호
• /
• pp.149-158
• /
• 1998

Biomass of non-living brown seaweed Sargassun fluitans pretreated with NaOH is capable of taking up more than $10\%$ $(q_{max}$ : 3.85 mmol/g for Al and 1.48 mmol/g for Cu) of its dry weight in the Al and Cu at pH of 4.5. However, the maximum Al and Cu uptakes calculated from Langmuir isotherm were 1.58 mmol/g for Al and 1.35 mmol/g for Cu at pH 3.5. Equilibrium batch sorption study was performed using two-metal system containing Al and Cu. The mathematical model of the two-metal sorption system enabled quantitative estimation of one-metal biosorption inhibition due to the influence of a second metal. NaOH-treated S. fluitans contained 2.19 mmol $(43\;wt.\%)$ carboxyl groups per gram of biomass. A modified form of Langmuir, which assumes binding of Cu as $Cu^{2+}$ and Al as $Al(OH)_2^+,$ was used to model the experimental data. This result agrees with the one of mono-valent sorption for Al in single-metal system. The modified Langmuir model gives the following affinity correlated coefficients: 0.196 for Cu and 6.820 for Ah at pH 4.5, and 2.904 for Cu and 3.131 for Al at pH 3.5. The interference of Al in Cu biosorptive uptake was assessed by `cutting' the three dimensional uptake isotherm surfaces at constant second-metal final concentrations. Equimolar final equilibrium concentrations of Cu and Al of 1 mM at pH 4.5 give Cu and hi uptakes reduced by $82.5\%\;and\;5.4\%,$ respectively. However, these values at pH 3.5 were $55\%\;(Cu)\;and\;31\%$ (Al).

• 마이크로전자및패키징학회지
• /
• 제10권1호
• /
• pp.1-5
• /
• 2003

본 연구에서는 ITO (indium tin oxide)/glass 투명기판 위에 다층구조의 OELD (organic electroluminescent devices) 소자를 진공 열증착법으로 제작하였다. 발광층 재료로서 Alq$_3$(tris-(8-hydroxyquinoline)aluminum)물질을 사용하였고, 정공수송층으로는 TPD (triphenyl-diamine) 및 $\alpha-NPD$를 사용하였다. 정공주입층 재료로서 CuPc (Copper phthalocyanine)를 사용하였다. 또한 QD2(quinacridone2) 물질을 $Alq_3$ 발광층내에 약 $10\AA$ 두께로 증착하여 발광효율 향상을 시도하였다. 제작된 모든 소자의 발광개시전압은 약 7 V 이었으며, 정공수송층으로 TPD 물질대신에 열적안정성이 우수한 $\alpha-NPD$를 사용한 경우 휘도값과 발광효율이 개선되었다. $Alq_3$ 발광층 사이에 QD2 물질을 적층한 소자에서 발광효율은 1.55 lm/W 값을 나타내어 $Alq_3$ 발광층만을 사용한 경우에 비해 약 8배 발광효율이 향상되었다.