• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.558-561
• /
• 2005

In-situ photopolymerization of alkyl acrylate monomers in the presence of a nematic fluid provides a cellular matrix of liquid crystalline droplets in which the chemical structure of the encapsulating polymer exerts control over the alignment (anchoring) of the liquid crystalline molecules. Control is obtained by variation of the alkyl side chains and through copolymerization of two dissimilar monofunctional acrylates. Two monofunctional acrylates with opposing tendencies on copolymerization provide control over the tunability of anchoring over a wide temperature range. Using various acrylates we show that a uniform vertical alignment can be achieved over a large area. Utilizing this technique and a nematic with negative dielectric anisotropy, we have fabricated highly flexible liquid crytal based devices, with high contrast and fast response time, without using any alignment layer.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.2
• /
• pp.528-535
• /
• 2016

Two types of oleophilic acrylic prepolymers were prepared by the solution copolymerization of either ethyl acrylate (EA) or lauryl acrylate (LA) with hydroxy ethyl acrylate (HEA). For the formation of oil-absorbent materials, a mixed solution of the prepolymer and hexamethylene diisocyanate (HDI) as a cross-linker in toluene was applied to polypropylene knit velvet fabric through the conventional pad-dry-cure procedure. The gel fraction of the crosslinked resin, EA-HEA-HDI, increased with increasing feed ratio of HEA to total acrylate or HDI concentration. The oil absorbancy and retention ratio of the prepared materials were compared according to the add-on ratio of resin to fabric, and were assessed with n-decane, toluene, soybean oil, lubricant and bunker C oil as test oils. The optimal oil absorbancy of the materials were observed at around 6% of the add-on ratio for all these oils except for soybean oil. On the other hand, the oil retention ratio increased as the add-on ratio increased. Futhermore, heavier and more viscous oil generally showed higher oil retention ratios. In addition, the oil absorbancy of the materials treated with LA-HEA-HDI resin was higher than that treated with EA-HEA-HDI resin, which showed that the acrylic resins are more absorptive with increasing length of their side alkyl chain.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.1
• /
• pp.142-151
• /
• 2017

Cationic surfactants have a bactericidal effect and the study for effective development of them became important parts in the industry. There have been increasing researches that focus on the development of products having not only outstanding features but also safety and biodegradability. In this work, novel ester-type cationic surfactants were obtained via Michael addition reaction. Intermediates were quantitatively prepared by the Michael addition reaction between alkyl acrylate and amine compounds under mild conditions without solvent and catalyst. The intermediates were quaternized with dimethyl sulfate. HQ21 with two hydrophobic groups and a hydrophilic group and HQ22 with two hydrophobic groups and two hydrophilic groups were obtained. The structures of the products were characterized by 1H-NMR, HR-MS and FT-IR and biodegradability of the products were tested.

• Journal of the Korean Chemical Society
• /
• v.35 no.3
• /
• pp.233-239
• /
• 1991

$N_1-alkyl-5-fluorouracil$ derivatives from 2-chloro-ethylacrylate(CEA) were synthesized. The reaction of 5-fluorouracil(5-FU) with 2-chloroethyl acrylate gave 1-hydroxyethyl-5-fluorouracil(HEFU) in 70% yield. The treatment of HEFU with acryloyl chloride afforded 1-acryloyloxyethyl-5-fluorouracil (AOEFU). Poly(1-acryloyloxyethyl-5-fluorouracil)[Poly(AOEFU)] was also synthesized from 5-fluorouracil and Poly(CEA). The hydrolysis rates of $N_1-alkyl-5-fluorouracil$ derivatives were observed by means of UV spectrophotometer at 265 nm in ethanol-water(1 : 1); k = the constant of hydrolysis rate, $k=1.38{\times}10^{-4}$/sec for HEFU, $k=9.25{\times}10^{-5}$/sec for AOEFU, $k=4.16{\times}10^{-5}$k = 4.16 ${\times}$ $10-5}sec$ for Poly(AOEFU). The differential thermal analysis and thermogravimetry of 5-fluorouracil derivatives have been discussed.

• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.523-530
• /
• 1999

Acrylic pressure-sensitive adhesive has been made utilizing organic solvents, but nowadays it is made by solvent-free system due to environmental problems. In this study, emulsion polymerization were carried out at $40^{\circ}C$ with methacrylic acid(MAA), n-butyl acrylate(n-BA) and 2-ethylhexyl acrylate(2-EHA) as monomers in the presence of anionic(sodium dodecyl sulfate, SDS) and nonionic(ethylene oxide types) surfactant mixtures. The overall conversion of the polymerization reaction in a mixed surfactant system was found to be higher than that in a single surfactant system. Emulsion stability in mixed or anionic surfactant systems was found to be over 12 week, which was better than that in nonionic surfactant system. Emulsion particle size decreased as surfactant content increased. The Tg and molecular weight of emulsion polymer were inependent of the type, the amount and the mixing ratio of surfactant. Based on the results of stability and peel strength, the optimum nonionic surfactant ratio in total 4 g of surfactant mixture systems is found to be 40~60% by weight where the nonionic surfactant has 50 ethylene oxide groups and 16~18 carbon atoms in hydrophobic alkyl chain.

• Polymer(Korea)
• /
• v.27 no.4
• /
• pp.364-369
• /
• 2003

The copolymerizations of 2-fluorohexylethyl acrylate (FA) with 2-(o-(1'-methylpropylidenamino)carboxyl amino)ethyl methacrylate(MEM) with different molar ratios of the two monomers were carried out in methyl ethyl ketone using ${\alpha}$,${\alpha}$'-azobisisobutyronitrile as an initiator to synthesize water repellent polyacrylate derivatives with protected isocyanate groups. The contents of FA and MEM in the copolymers were analyzed by NMR. The monomer reactivity ratios of MEM (1) and FA (2) were determined by Kelen-Tudos plot as follows : r$\_$1/＝1.59 and r$\_$2/＝0.50. The number-average molecular weights of the copolymers were in the range of 39400 to 72400 and the polydispersity indexes were about 1.5. The protected isocyanate groups in the copolymers were converted into isocyanate groups above 150$^{\circ}C$. The contact angle of the copolymer with 65 ㏖% of FA fur water was about 95$^{\circ}$.

• Polymer(Korea)
• /
• v.29 no.5
• /
• pp.433-439
• /
• 2005

The copolymers were prepared by the emulsion copolymerization of fluoroalky lacrylate-stearylacrylate-m-isopropenyl-${\alpha},\;{\alpha}'$-dimethylbenzyl isocyanate (TMI) in order to obtain water repellent polymers. The respective copolymerization rates of the three monomers considerably depended upon the use of the nonionic emulsifier and the nonionic-cationic mixed emusifier, and the optimum conditions were obtained. The particle sizes of the copolymers were in the range of 105 to 222nm. The particle sizes of the copolymers prepared by the use of the mixed emulsifiers were smaller than those of the copolymers prepared by the use of the nonionic emulsifier. The reactions of both TMI-N-methyl acetamide and TMI-cellobiose did not take place. However, the reaction of TMI-n-butylamine occurred. The water contact angles before and after washing three times for nylon and poly(ethylene terephthalate) (PET) fabrics coated with the copolymer prepared by the use of mixed emulsifier were about $139^{\circ}\;and\;133^{\circ}$ Therefore, the copolymer showed good durable repellency for nylon and PET.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.24 no.3
• /
• pp.116-122
• /
• 1998

It is well known that all-trans-retinol is not only very unstable in heat, light, air, and water, but also skin-irritant despite a good anti-wrinkle effect. Therefore, it is very difficult to stabilize retinol and make the safe retinol containing cosmetics by using a certain concentration of retinol with real effect. In order to dissolve these problems and apply retinol for skin care cream, firstly retinol is to be encapsulated in the vesicle called Liposphere (pseudo-liposome) which is made by homogenizing under high pressure the mixtures of lecithin, retinol, caprylic/capric triglyceride, and hydroalcoholic solution ; and then this retinol containing Liposphere is to be intercalated in lamellar liquid crystal layer which is prepared by emulsifying in an optimal ratio the mixtures composed of non-ionic emulsifier (cetearyl glucoside, sorbitan stearate & sucrose cocoate etc), cetearyl alcohol, stearic acid, cholesterol, and ceramide. In addition, the stability of the retinol containing oil in water cream by adding the polymeric emulsifier such as acrylate /C10-30 alkyl alkylate crosspolymer is to be ensured even at 55 C. Retinol containing oil in water cream prepared through above procedure could be very stable at 45 C for at least 50 days. The structure identification of lamellar liquid crystal was determined using polarized light microscope and electron microscope Conclusively, we could make the very stable retinol containing oil in water cream by triple procedure, that is, encapsulation of retinol in Liposphere, intercalation of retinol in lamellar liquid crystal layer, and assurance of the high temperature stability of cream even at 55 C.

• Journal of Adhesion and Interface
• /
• v.14 no.1
• /
• pp.1-12
• /
• 2013

Multi core-shell composite particles were prepared by the water-born emulsion polymerization of various core monomers such as methyl methacrylate (MMA), ethyl methacrylate (EMA) and shell monomers such as MMA, EMA, 2-hydroxyl ethyl methacrylate (2-HEMA), glycidyl methacrylate (GMA) and methacrylic acid (MAA) in the presence of different concentrations of sodium dodecyl benzene sulfonate (SDBS). The following conclusions are drawn from the conversion, particle size and distribution, average molecular weight, molecular structure, glass transition temperature with DSC, contact angle after plasma treatment, tensile strength and isothermal decomposition kinetics. In the case of the concentration of 0.02 wt% SDBS, the conversion of MMA core-(EMA/GMA) shell composite particles was excellent as 98.5%. In the case of the concentration of 0.03 wt% SDBS, the particle size of EMA core-(MMA/GMA) shell composite particles was high as $0.48{\mu}m$. We confirmed that 3 points of glass transition temperatures appear for multi core-shell composite particles compared to 1~2 points of glass transition temperatures appear for general copolymer particles. Overall, the adhesion strength of shell composite particles was in the order of EMA/MAA > EMA/2-HEMA > EMA/GMA.

• Journal of Adhesion and Interface
• /
• v.12 no.1
• /
• pp.16-25
• /
• 2011

Multi core-shell composite particles were prepared by the water-born emulsion polymerization of various core monomer such as methyl methacrylate (MMA), n-butyl methacrylate (BMA), and shell monomer such as MMA, BMA, stylene (St), 2-hydroxyl ethyl methacrylate (2-HEMA) and acrylic acid (AA) in the presence of different concentration of sodium dodecyl benzene sulfonate (SDBS). The following conclusions are drawn from the measured conversion, particle size and distribution, average molecular weight, molecular structure, glass transition temperature with DSC, morphology, tensile strength and elongation. In the case of the concentration of 0.02 wt% SDBS, the conversion of MMA core-(BMA/St/AA) shell composite particle was excellent as 98%. In the case of the concentration of 0.03 wt% SDBS, the particle size of BMA core-(MMA/St/AA) shell composite particle was high as $0.47{\mu}m$. We confirmed that 3 points of glass transition temperatures appear for multi core-shell composite particles compared to 2 points of glass transition temperatures appear for general core-shell composite particles. We showed that it is possible to adjust glass transition temperatures according to the kind and composition of the inner shell monomer that it is can be used as a adhesive binder material with improved adhesive power.