• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.545-548
• /
• 2006

This study has been carried out to examine the properties of concrete according to replacement ratio and curing method of fly ash, in order to increase utilization of it. As the result of experiments, the 7 days of early age strength presented around 20MPa, up to 20% of replacement ratio, which is almost the same strength as non-replacement. However, when the replacement ratio was 30%, the strength was decreased to 16MPa, as 20% reduction compared to the non-replacement condition. In 365 days of long term aging, the strength was 5% higher, up to 20% of the replacement ratio, due to the pozzolanic reaction of fly ash. When the replacement ratio was 30%, it presented similar strength development as the non-replacement condition. Steam curing and autoclave curing increased the short age strength, regardless of the replacement ratio of fly ash; however, they don't have an effect on increasing the 365 days of long term strength. Water curing showed high strength development after 28 days, 51.81MPa, which is around 30% higher than air curing, 38.9MPa, steam curing, 38.6MPa, and autoclave curing, 39MPa. Therefore, water curing was examined as one of the very effective curing methods for developing long term strength of concrete.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 추계 학술논문 발표대회
• /
• pp.27-28
• /
• 2019

In this study, the characteristics of compressive strength of ultra high strength concrete supplied with moisture from outside by vacuum water absorbing curing method were investigated. Specimens were prepared by replacing the binder(Silifa fume and GGBS) by 25 wt% with respect to the weight of cement at W/B 0.16. Each specimen was subjected to water Vacuum absorbing curing time 0 min, 30 min, 60 min, 90 min and 120 minutes immediately after the demolding. Curing was performed at $20^{\circ}C$ Air-dry curing, $90^{\circ}C$ steam curing, $90^{\circ}C$ steam curing and $180^{\circ}C$ autoclave curing. Experimental results showed that water absorbing degree increased with increasing water absorbing curing time, and BS25 sample had higher water absorbing degree than SF25 sample at same time. Compressive strength tended to increase up to about 40% in water absorbing degree, but compressive strength decreased again in water absorbing more than 40%.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 추계 학술논문 발표대회
• /
• pp.107-108
• /
• 2011

The purpose of present study is to examine the application of effective curing to hardener-free epoxy-modified mortars. The epoxy-modified mortars are prepared with polymer-cement ratios, subjected to two types of curing conditions, and tested for compressive, flexural and tensile strengths. As a result, hardener-free epoxy-modified mortars with steam curing is markedly improved with increasing air-dry curing period. High strength development of the epoxy-modified mortars may be achieved by the dense microstructure by cement and the hardener of the epoxy resin in the mortars.

• 한국연초학회지
• /
• 제5권1호
• /
• pp.79-85
• /
• 1983

The greenhouse bulk curing and drying system utilization of the direct solar energy was tested to evaluate that how much fuel could be saved for curing flue-cured tobacco at the Dae Gu Experiment Station (North latitude : $35^{\circ}$49'), in 1979-1982. The air temperature and total radiation were 19.0 to 38.5$^{\circ}C$ and 1311.0 to 1412.7 cal/$\textrm{cm}^2$/day during the 4 replicated curing test, respectively. The greenhouse bulk curing and drying system was able to cut fuel consumption by 32% compared with the conventional bulk curing barn. We could obtain almost same utilization efficiency of solar energy in 1982 compare with normal year, mainly increasing the heat receiving area.

• 대한토목학회논문집
• /
• 제29권5C호
• /
• pp.207-215
• /
• 2009

시멘트 혼합토나 콘크리트는 일반적으로 습윤상태를 유지하면서 양생이 되며 양생기간이 늘어남에 따라 수화작용으로 강도는 증가한다. 하지만 양생기간 동안 시멘트 혼합토에 충분한 수분이 공급되지 않을 경우 이는 수화작용에 영향을 미치고 결국 시멘트 혼합토의 강도 변화를 가져오게 된다. 본 연구에서는 시멘트비가 20% 미만인 시멘트 혼합토가 현장에서 시공 될 때 발생할 수 있는 수분공급 조건을 고려하여 네 가지 양생방법(대기중 양생, 밀봉 양생, 습윤 양생, 수중 양생)으로 제작된 고결모래의 양생조건에 따른 일축압축강도의 특성을 비교하였다. 전기간(3일) 대기중 양생한 공시체의 강도는 시멘트비가 10% 미만인 경우 밀봉 및 습윤 양생한 공시체보다 크지만 시멘트비가 10% 이상인 경우는 더 작았다. 시멘트비에 관계 없이 대기중 양생한 공시체가 수중 양생한 공시체보다 더 큰 강도를 발휘하였다. 양생방법이 동일한 경우 시멘트비 4%의 강도를 기준으로 시멘트비 증가에 따른 강도 증가율은 대기중 양생한 공시체가 가장 낮았으며, 밀봉, 습윤 및 수중 양생한 공시체의 강도는 시멘트비 증가율의 제곱으로 증가하였다. 공시체를 2일 양생 후 1일 동안 수침시켰을 때 밀봉 또는 습윤 양생한 공시체의 강도는 수침시키지 않은 공시체보다 시멘트비에 관계없이 평균 10% 정도 저하되었으나, 대기중 양생한 공시체는 시멘트비가 낮은 경우 최대 30% 정도까지 크게 저하되었다. 본 연구 결과는 현장에서 발생하는 수분공급 조건과 수침에 따른 시멘트 혼합토의 강도 변화를 예측하여 시멘트 혼합토를 사용한 댐과 같은 지반구조물의 안정성 확보에 기여할 수 있다.

• 한국작물학회지
• /
• 제34권2호
• /
• pp.204-210
• /
• 1989

오리엔트종 연초에서 전조조건에 따른 품질과 화학성분의 변화를 구명하기 위하여 수확엽을 황변시킨 후 각각 벌크건조 4$0^{\circ}C$, 5$0^{\circ}C$, 6$0^{\circ}C$구, 양건 및 음건으로 처리하여 분석한 결과는 다음과 같다. 1. 품질은 음건엽이 유의하게 낮았으며, 양건과 벌크건조엽은 차이가 적었다. 2. 음건엽은 양건엽과 벌크건조엽에 비해 암모니아태 질소, 단백태 질소, 전질소, 회분함량 및 pH가 높고 당함량이 낮았으며, 석유에텔 추출물과 휘발성 유기산함량은 차이가 적었다. 3. 석유에텔 추출물, 휘발성 유기산과 대부분의 정유성분 중성부함량은 벌크건조 온도가 높을수록 감소하거나 변화가 없었다. 4. 오리엔트종 잎담배의 품질평가 지수로 (총 휘발성 유기산(mg/100g)+석유에텔추출물(%)) / (회분(%)+pH) $\times$ 10 이 추천된다.

• 한국산업융합학회 논문집
• /
• 제26권4_2호
• /
• pp.629-637
• /
• 2023

This study aimed to evaluate the effect of post-curing equipment and time on the flexural strength of 3D printing resins produced by a liquid crystal display(LCD) printer. The three 3D printing resins(DENTCA Denture Teeth, DT; C&B 5.0 hybrid, CH; C&B Permanent A2, CP) were divided into four groups according to post-curing time(10 min and 30 min) and equipment with or without vacuum treatment. For the three-point flexural strength test and biaxial strength test were prepared by method according to ISO 10477, ISO 6872, respectively. Flexural strength was measured with universal testing machine. Comparison between post-curing time of each post-curing equipment was analyzed by independent sample t-test and Mann-Whitney U test(α=.05), and comparison between groups according to each 3D printing resin was performed by Kruskal-Wallis test and post-hoc by Bonferroni-Dunn test(α=.05). The flexural strength of the resin post-curing under vacuum was higher than that of the resin post-curing in air. In the comparison according to the post-curing time, in the case of the post-curing equipment without vacuum, the 30 minute curing time showed significantly higher flexural strength than the 10 minute curing time, except for the biaxial flexural strength of CH(P<.05). In the post-curing equipment with vacuum, the three-point flexural strength of all 3D printing resins(DT, CH, and CP) showed a higher value at 30 minute curing time than at 10 minute curing time.

• 대한치과보철학회지
• /
• 제43권1호
• /
• pp.52-60
• /
• 2005

Purpose. The intent of this study was to evaluate the effects of curing conditions on self-curing denture base resins to find out proper condition in self-curing resin polymerization. Materials and methods, In this study, 3 commercial self-curing denture base resins are used Vertex SC, Tokuso Rebase and Jet Denture Repair Acrylic. After mixing the self curing resin, it was placed in a stainless steel mold(3$\times$6$\times$60mm). The mold containing the resin was placed under the following conditions: in air at 23$^{\circ}C$; or in water at 23$^{\circ}C$; or in water at 23$^{\circ}C$ under pressure(20psi); or in water at 37$^{\circ}C$ under pressure(20psi) or in water at 50$^{\circ}C$ under pressure(20psi) , or in water at 65$^{\circ}C$ under pressure(20psi), respectively. Also heat-curing denture base resin is polymerized according to manufactures' instructions as control. Fracture toughness was measured by a single edge notched beam(SENB) method. Notch about 3mm deep was carved at the center of the long axis of the specimen using a dental diamond disk driven by a dental micro engine. The flexural test was carried out at a crosshead speed 0.5mm/min and fracture surface were observed under measuring microscope. Results and conclusion . The results obtained were summarized as follows : 1. The fracture toughness value of self-curing denture base resins were relatively lower than that of heat-curing denture base resin. 2. In Vertex SC and Jet Denture Repair Acrylic, higher fracture toughness value was observed in the curing environment with pressure but in Tokuso Rebase, low fracture toughness value was observed but there was no statistical difference. 3. Higher fracture toughness value was observed in the curing environment with water than air but there was no statistical difference. 4. Raising the temperature in water showed the increase of fracture toughness.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.157-162
• /
• 2002

This study is intended to present a reference data for effective quality control of concrete through comparing the rebound value of P type schmidt hammer with the compressive strength with variation of mix proportion and curing condition. According to the results, the air-curing specimen shows the higher rebound value than standard specimen except high strength in the whole. Also the vertical stroke shows higher rebound value than horizontal stroke in standard specimen, however, the rebound value of the two does not show prominent difference in air-curing specimen. The estimation equation of compressive strength derived from this experiment estimates the compressive strength more largely than the estimation equation in P type schmidt hammer manual. Therefore it is thought that the new estimation equation that fits our condition will have to be presented.

• International Journal of Concrete Structures and Materials
• /
• 제6권4호
• /
• pp.251-256
• /
• 2012

This paper presents an experimental study on the pore and penetration of chloride in seashore concrete depending on types of curing forms. Three types of concretes (Plain concrete, MSF concrete and FA concrete) with four different form types (wood, coating wood, steel and polypropylene film) were examined. The test results show that the air volume in concrete was relatively higher with steel and polypropylene forms than others, and wood form shows the least air volume. The penetration of chloride depending on type of form is showed a wide variability, that is, the values on plain concrete, MSF concrete and FA concrete are 115.2, 125.5 and 121.6 %, respectively. Based on the present study, concrete should be considered the conditions of curing form-type for durable concrete.