• Journal of Biosystems Engineering
• /
• v.23 no.1
• /
• pp.1-12
• /
• 1998

This study was intended to investigate experimentally the effect of inflation pressure on tractive performance of bias-ply tires for agricultural tractors. Traction tests were conducted at the three velocities of 3, 4, and 5.5km/h under few different surface conditions using a 13.6-28 6PR bias-ply tire as driving wheel of the test tractor. When the inflation pressure was reduced from 250kPa to 40kPa by a decrement of either 30 or 50kPa depending upon the test surface conditions, some of the test results showed that the tractive coefficient and efficiency were increased maximally by 40% and 17％, respectively, at 20% slippage. However, it was failed to derive any consistent rules depicting the effect of inflation pressure of bias ply tires on the tractive performance of tractors.

• Journal of Biosystems Engineering
• /
• v.21 no.1
• /
• pp.3-9
• /
• 1996

Sowing with an automatic seed metering device is increasing in popularity. Since 100% planting is not likely, a major problem is to find any place which contains no seeds between row spacings in the agricultural field. Automatic sowing technology, including the implementation of a microcomputer, appears to be an attractive alternative to the use of manual labor for accomplishing this task. Thus, the multi-purpose seeder attached to a cultivator was designed and constructed with an automatic seed metering device. This seeder proved to be a reliable system for sowing seeds in the agricultural field. Multi-purpose seeder for cultivator consists of an automatic seed metering device, a trench device, a covering device, and a press wheel

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.404-412
• /
• 1996

For the cultivation of big agricultral areas high performance machinery is needed. The need to increase working productivity also leads to powerful machinery. The total weight of new tractor generations increases and with it their axle and wheel weight reaches a soil damaging extend. Besides carrying the mass of the tractors and harvesting-machines the chassis must transmit driving force onto the ground(Tab. 1). To decrease soil damaging compaction a number of technical solutions have been developed. Broad tyres are being used to minimize the contact-area pressure by using low tyre air pressure. For enlarging the contact area there are two-possibilities : to build a brought or a long contact area. done for instance in caterpillar tracks.

• Korean Journal of Agricultural Science
• /
• v.43 no.4
• /
• pp.650-655
• /
• 2016

Gears are components of transmission which transmit the power of an engine to a machine and offer numerous speed ratios, a compact structure, and high efficiency of power transmission. Gear train design in the automotive industry uses simulation software. However, PTO (Power Take-Off) gear design for agricultural applications uses the empirical method because of the wide range of load fluctuations in agricultural fields. The PTO is an important part of agricultural tractors which transmits the power to various tractor implements. Therefore, a simulation was essential to the optimal design of the PTO. When the PTO gear is optimally designed, there are many advantages such as low cost, reduced size, and light weight. In this study, we conducted the bending and contact safety factor simulation for the PTO gear of an agricultural tractor. The bending and contact safety factors were calculated on ISO 6336 : 2006 by decreasing the face widths of the PTO pinion and wheel gear from 18 mm at an interval of 1 mm. The safety factor of the PTO gear decreased as the face width decreased. The contact safety factors of the pinion and wheel gear were 1.45 and 1.53, respectively, when the face width was 18 mm. The simulation results showed that the face width of the PTO gear should be greater than 9 mm to maintain the bending and contact safety factors higher than 1. It would be possible to reduce the weight of the PTO gear for different uses and working conditions. This study suggests that the possibility of designing an optimal PTO gear decreases as its face width decreases.

• Journal of Animal Environmental Science
• /
• v.12 no.3
• /
• pp.151-160
• /
• 2006

For even distribution of liquid manure in the field, a boom nozzle type spreader was designed and studied to determined its suitability for small scale crop production farms. Boom nozzle type spreader was compared in the impact triple nozzle and impact single nozzle type spreader. Spreading uniformity of the boom nozzle type liquid manure spreader showed 5.2% (C.V.) and impact single nozzle type spreader showed 6.9% (C.V.). The spreading uniformity of the impact triple nozzle type spreader was quite uneven, therefore, the spreader could be modified as twin nozzle for spreading in orchard farm. The wheel axle height adjustable type liquid manure spreader has higher the stability and it considered much useful on the hilly agricultural land.

• Korean Journal of Agricultural Science
• /
• v.51 no.2
• /
• pp.133-146
• /
• 2024

Selection of gear reduction ratio is essential for machine design to ensure suitable power and speed during agricultural operations. The goal of the study was to evaluate the gear reduction ratio for a 1.6 kW four-wheel-drive (4WD) multi-purpose agricultural electric vehicle platform using workload data under different off-road conditions. A data acquisition system was fabricated to collect workload (torque) of the vehicle acting on the gear shaft. Field tests were performed under three driving surfaces (asphalt, concrete, and grassland), payload operations (981, 2,942, and 4,903 N), and slope conditions (0 - 4°, 4 - 8°, and 8 - 12°), respectively. Commercial speed reduction gear phases were attached to the input shaft of the vehicle powertrain. The maximum required torque was recorded as 37.5 Nm at a 4,903 N load with 8 - 12° slope levels, and the minimum torque was 12.32 Nm at 0 - 4° slope levels with a 981 Nm load for a 4 km/h speed on asphalt, concrete, and grassland roads. Based on the operating load condition and motor torque and rotational speed (TN) curve, the minimum and maximum gear reduction ratios were chosen as 1 : 50 and 1 : 64, respectively. The selected motor satisfied power requirements by meeting all working torque criteria with the gear reduction ratios. The chosen motor with a gear reduction ratio of 1 : 50 was suitable to fit with the motor T-N curve, and produced the maximum speeds and loads needed for driving and off-road activities. The findings of the study would assist in choosing a suitable gear reduction ratio for electric vehicle multi-purpose field operations.

• Journal of Biosystems Engineering
• /
• v.17 no.1
• /
• pp.27-36
• /
• 1992

Computer simulation was carried out to predict the motion and overturns of power tiller-trailer system this system when traveing over an obstacle on inclined planes. To estimate the effects of design factors (mass center of main body and wheel base), ground factors (ground inclination and height of obstacle), and operation factors (traveling velocity) on the sideways overturn, the motion of power tiller-trailer system was simulated as the factors were varied with five different levels.

• Korean Journal of Agricultural Science
• /
• v.51 no.1
• /
• pp.63-77
• /
• 2024

Yield monitoring systems have become integral to precision agriculture, providing insights into the spatial variability of crop yield and playing an important role in modern harvesting technology. This paper aims to review current research trends in yield monitoring systems, specifically designed for non-grain crops, including cabbages, radishes, potatoes, and tomatoes. A systematic literature survey was conducted to evaluate the performance of various monitoring methods for non-grain crop yields. This study also assesses both mass- and volume-based yield monitoring systems to provide precise evaluations of agricultural productivity. Integrating load cell technology enables precise mass flow rate measurements and cumulative weighing, offering an accurate representation of crop yields, and the incorporation of image-based analysis enhances the overall system accuracy by facilitating volumetric flow rate calculations and refined volume estimations. Mass flow methods, including weighing, force impact, and radiometric approaches, have demonstrated impressive results, with some measurement error levels below 5%. Volume flow methods, including paddle wheel and optical methodologies, yielded error levels below 3%. Signal processing and correction measures also play a crucial role in achieving accurate yield estimations. Moreover, the selection of sensing approach, sensor layout, and mounting significantly influence the performance of monitoring systems for specific crops.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.10
• /
• pp.80-87
• /
• 2021

Our study introduces an improved modular agricultural platform to provide convenience to agricultural workers. We upgrade the platform design in three parts, namely, by adding a 458 pattern tire, electricity control, and four-wheel steering function, to improve the platform performance. Results showed that the upgrades enhanced the platform performance and reduced its overall weight as compared with the existing platform. To demonstrate the performance of our improved platform, we conducted five types of experiments with respect to the climbing angle, variable width, attitude control, speed, and obstacle passing.

• Coupled systems mechanics
• /
• v.12 no.1
• /
• pp.1-20
• /
• 2023

On the basis of the explicit time-domain method, an investigation is performed on the influence of the rotational stiffness and rotational damping of the vehicle body and front-rear bogies on the dynamic responses of the vehicle-bridge coupled systems. The equation of motion for the vehicle subsystem is derived employing rigid dynamical theories without considering the rotational stiffness and rotational damping of the vehicle body, as well as the front-rear bogies. The explicit expressions for the dynamic responses of the vehicle and bridge subsystems to contact forces are generated utilizing the explicit time-domain method. Due to the compact wheel-rail model, which reflects the compatibility requirement of the two subsystems, the explicit expression of the evolutionary statistical moment for the contact forces may be performed with relative ease. Then, the evolutionary statistical moments for the respective responses of the two subsystems can be determined. The numerical results indicate that the simplification of vehicle model has little effect on the responses of the bridge subsystem and the vehicle body, except for the responses of the rotational degrees of freedom for the vehicle subsystem, regardless of whether deterministic or random analyses are performed.