• Magazine of the Korea Concrete Institute
• /
• v.2 no.3
• /
• pp.81-88
• /
• 1990

For the protectioon of radioactive leakage, the quality control of main concrete structure in nuclear power plants is very important. So, this studey is designed to analyze the influence of kind of cement and aggregate on the mechanical properties of high density concrete. Test results of this study are as follows; 1)The slump of magnetite aggregate concrete(MAC) is found half value of nat.ural aggregate concrete (NAC). 2)As the effect of cement, the compressive strength of concrete using moderate heat cement is found higher 5-19 % than that of ordinary portland cement. 3)As the effect of fine aggregate, t.he compressive strength of MAC is found higher than that. of NAC below 340kg/$cm^2$ and lower t.han NAC above 340kg/$cm^2$. 4)As the effect of coarse aggregate, the compressive strength of MAC is found higher 17-22% than that of NAC.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.465-468
• /
• 2008

This study investigated the best condition when mixed sand with a river and crushed sand was used though the experiment for the properties of the concrete corresponding to the control of fine aggregate ratio to apply the mixed sand and properties of the fine aggregate at the ready-mixed concrete factory on Yeongnam and Honam. The physical properties of Yeongnam and Honam is satisfied with KS F 2526 and KS F 2527 except fineness modulus and passing amount of 8mm sieve. And, the mixed sand above two types which were incongruent to use individually was being used at each factory, and it was managed in accordance with KS. The flowabillity of the mixture proportion of concrete which was estimated by method of unit volume weight according to the fine aggregate ratio at each factory on Yeongnam and Honam was higher than existing mixture proportion. It was analyzed that the residual water due to decline of the surface area caused by reducing fine aggregate ratio was increased relatively. Accordingly, it was considered that the effect on the economic mixture proportion and improvement of durability might be possible.

• Journal of Adhesion and Interface
• /
• v.6 no.1
• /
• pp.7-10
• /
• 2005

Condensation control of nano-particles has become important in order to fabricate minute condensed structures. In this study, we focus our attention on condensation mechanism of polymer aggregates in a resist film. The polymer aggregate is structural component of a resist material which is used in lithography process. The condensation nature of polymer aggregates in the resist film surface is observed by using atomic force microscope (AFM). By using the AFM, the condensation of polymer aggregates can be observed clearly. The condensation of polymer aggregate strongly affects to precise fabrication of resist pattern below 100nm size. The interaction force among polymer aggregates can be analyzed based on Derjaguin approximation. We also discuss about condensation nature of polymer aggregates in the resist film surface with the help of micro sphere model.

• 한국방재학회:학술대회논문집
• /
• 2007.02a
• /
• pp.117-120
• /
• 2007

The main purpose of this paper is to introduce the early traffic opening-capable continuous multi-layer asphalt pavement maintenance method using electric arc furnace slag aggregate and emulsified asphalt to the actual construction sites. As well known, the previous surface treatment method of emulsified asphalt mixture have various shortcomings such as long work-time, traffic congestions, plastic deformation and poor evenness. Thus, the proposed method has enabled tile early traffic opening by utilizing the optimized emulsified asphalt after consideration of the climate and road conditions in Korea. The application of the electric furnace slag with $6\;{\sim}\;18\;mm$ thickness is helpful to become a environment-friendly construction method. And also, it has been improved enough to accommodate night-time works of mechanized construction activities for wearing course and control course.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.337-338
• /
• 2009

Use of the recycled fine aggregate as a material of structural concrete is not easy currently because there are some problems, such as of quality control and the uncertainty of chemical and physical property. Thus, the results indicate that it is possible to produce high quality recycled fine aggregate for structure by microwave heating technology, friction and abrasion action.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.189-192
• /
• 2004

This study bases on showing the pictures of how to keep a recycled fine aggregate well (quality control) and how to invent the measurement of mortar's quantities which largely effect on basic properties of matter: strength, durability and so on. As a result of the experiment by immersion, quantities of adhesive cement takes 7 to 8 days to stabilize by sulfuric. However, by hydrochloric acid, it takes a little quicker due to the first quick reaction, aggregate of the measurement of adhesive mortar by immersion used acid liquids are likely applicable following a suitable inspection and complementarity.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.195-198
• /
• 2009

Rammed Aggregate Pier method is intermediate foundation of deep and shallow foundation, it has been built on world wide. But the investigation and research in domestic is not accomplished. In this paper, examined details of different spacing of piles, bearing capacities, respectively, conclude with recommendations on how RAP can be used in future needs. This documentation further provides comparisons of the laboratory test results which were obtained from differenciate the spacing of piles, namely installed rammed aggregate pier. Strain control test was conducted to determine the bearing capacities of the piers; 20mm, 30mm and 40mm diameter drilling equipment to drill holes were installed in sand at initial relative densities of 40%. By comparing different spacing of piles, in this experiment, piles are spaced structually span, form a ring shape, narrowing the distance of each other, to the center. the result shows that as diameter of pier is bigger in diameter, bearing capacity also dramatically increased due to raised stiffness. Also, the space between each piers narrowed, settlement rate of soil was decreased significantly. From the test results, as the space between each piles were getting closer, allows greater chances to have resistance to deformation, shows improved stability of structures.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2003.05a
• /
• pp.61-65
• /
• 2003

Bottom ash among the coal ash is not used because of its poor properties. But encouraging the use of bottom ash as a construction material is a sensible method of utilization as it avoids the problems and costs associated with disposal and provides an alternative aggregate source. This study was aimed at using bottom ash as an alternative fine aggregate source to provide a solution to disposal and insufficient fine aggregate for the production of concrete. So properties of domestic bottom ash were estimated due to the difference of each domestic bottom ash. And compressive strength and durability were estimated as basic data to use bottom ash in building industries. As a result of the experiment, the very porous surface and angular shape of the bottom ash particles necessitate a higher apparent water-cement ratio. And due to the higher water requirement, the compressive strength and durability of mortar is lower than those of the control samples. But when 25 percent of the total dry weight of the natural fine aggregate was replaced by bottom ash, the engineering characteristics were similar.

• Journal of the Korea Institute of Building Construction
• /
• v.14 no.2
• /
• pp.187-194
• /
• 2014

With environmental regulations continuously being strengthened internationally the need to control environmental pollution and environmental load is emerging in Korea. The purpose of this study is to seek methods or using waste cementitious powder as an alternative raw material for limestone through the optimization of raw material and to quantitatively analyze the resulting reduction of $CO_2$ emission in order to contribute to solving the issue of waste, which is the biggest issue in relation to construction and global warming. The results of the study, show that waste cementitious powder can be used as an alternative raw material for limestone at OPC level, but it was also found that mixing fine aggregate cementitious powder into waste cementitious powder significantly affected the substitution rate for limestone with waste cementitious powder and the reduction of greenhouse gas. In particular, when fine aggregate cementitious powder was used at a rate of 0~20%, the substitution rate for limestone and the reduction in the rate of greenhouse gas emission was significantly reduced. It is thought that a technique to efficiently separate and discharge the fine aggregate cementitious powder mixed in waste cementitious powder needs to be developed in the future.

• International conference on construction engineering and project management
• /
• 2015.10a
• /
• pp.405-410
• /
• 2015

Today, the booming construction in Ethiopia is leading to an increased demolition of concrete structures whereby these demolished structures are disposed at landfills. The current practice is creating a huge amount of waste which is environmentally unfriendly and is becoming the main source of pollution in communities. This paper discusses the potential use of demolished concrete from site tested specimens as a recycled aggregate material for new structural concrete. The mechanical, physical and chemical properties of RCA are studied to understand the suitability in the production of recycled concrete. Tests including gradation, unit weight, soundness, density, and abrasion will be conducted to assess RCA properties. Since the percentage of RCA govern the strength of concrete, a C25 concrete is mixed by the ratio of 25%, 50% & 100% RCA with and without water reducing admixture and a control mixture composed of natural aggregate. The output of this study will highly impact the growing construction industry and communities in Ethiopia thereby reducing waste, saving cost, conserving natural aggregates, building capacity and setting quality standards.