• Journal of Magnetics
• /
• 제11권1호
• /
• pp.30-35
• /
• 2006

A thorough study about the influences of Mn substitution for Fe on the microstructure and magnetic characteristics of $Fe_{73.5-x}Mn-{x}Si_{13.5}B_{9}Nb_{3}Cu_1$ (x = 1, 3, 5) alloys prepared by the melt-spinning technique has been performed. Nanocomposites composed of nanoscale $(Fe,Mn)_{3}Si$ magnetic phase embedded in an amorphous matrix were obtained by annealing their amorphous alloys at $535^{\circ}C$ for 1 hour. The addition of Mn causes a slight increase in the mean grain size. The Curie temperatures of the initial amorphous phase and of the nanocrystals phase decreased, while the Curie temperature of the remaining amorphous phase remained nearly constant with increasing Mn content. Soft magnetic properties of the crystallized samples have been significantly improved by a proper thermal treatment. Accordingly, the giant magnetoimpedance effect is observed and ascribed to the increase of the magnetic permeability, and the decrease of the coercivity of the samples. The increased magnetic permeability is resulted from a decrease in the magnetocrystalline anisotropy and saturation magnetostriction.

• 한국세라믹학회지
• /
• 제44권4호
• /
• pp.198-201
• /
• 2007

Multi-walled carbon nanotube (M-CNT)/Nafion nanocomposites were prepared by solution casting to elucidate the effect of M-CNT addition, from 0 to 7 wt%, on the viscoelastic behavior of the composites. The M-CNT bundles induced by the Nafion polymer were determined to be uniformly distributed for the 1 wt% M-CNT/Nafion nanocomposites. The 1 wt% M-CNT/Nafion composite exhibited the highest blocking stress of 2.3 kPa due to its high elastic modulus of 0.485 GPa. From a dynamic mechanical analysis, the 1 wt% M-CNT had the highest storage and loss moduli compared with the other samples in all frequency and temperature ranges. From the storage modulus data, the M-CNT loaded composites had similar $T_g$ values near $120^{\circ}C$. The glass transition temperatures of the M-CNT loaded composites were $120^{\circ}C$ (1 wt%), $117^{\circ}C$ (3 wt%), $117^{\circ}C$ (5 wt%), and $135^{\circ}C$ (7 wt%), suggesting that the effect of the M-CNTs on the Nafion film begins at 1 wt%. Thus, it has been concluded that the 1 wt% M-CNT disported composite is attractive for actuator applications.

• Nano
• /
• 제13권11호
• /
• pp.1850129.1-1850129.10
• /
• 2018

To improve the high charge carrier recombination rate and low visible light absorption of {001} facets exposed $TiO_2$ [$TiO_2(001)$] nanosheets, few-layered $MoS_2$ nanoparticles were loaded on the surfaces of $TiO_2(001)$ nanosheets by a simple photodeposition method. The photocatalytic activities towards Rhodamine B (RhB) were investigated. The results showed that the $MoS_2-TiO_2(001)$ nanocomposites exhibited much enhanced photocatalytic activities compared with the pure $TiO_2(001)$ nanosheets. At an optimal Mo/Ti molar ratio of 25%, the $MoS_2-TiO_2(001)$ nanocomposites displayed the highest photocatalytic activity, which took only 30 min to degrade 50 mL of RhB (50 mg/L). The active species in the degradation reaction were determined to be $h^+$ and $^{\bullet}OH$ according to the free radical trapping experiments. The reduced charge carrier recombination rate, enhanced visible light utilization and increased surface areas contributed to the enhanced photocatalytic performances of the 25% $MoS_2-TiO_2(001)$ nanocomposites.

• Nano
• /
• 제13권10호
• /
• pp.1850118.1-1850118.17
• /
• 2018

Nanoparticles of the semiconductor catalyst $Cd_xZn_{1-x}S$ were embedded into the metal organic framework MIL-101(Cr) to obtain $Cd_xZn_{1-x}S@MIL-101$(Cr) nanocomposites. These materials not only possess high surface areas and mesopores but also show good utilization of light energy. The ultraviolet-visible diffuse reflectance patterns of $Cd_xZn_{1-x}S@MIL-101$(Cr) nanocomposites showed that $Cd_{0.8}Zn_{0.2}S@MIL-101$(Cr) possessed good visible light response ability among the synthesized nanocomposites. The photocatalytic performance of the $Cd_xZn_{1-x}S@MIL-101$(Cr) nanocomposites were tested via degradation and mineralization of methylene blue in neutral water solution under light irradiation using a 300W xenon lamp. As a result, using $Cd_{0.8}Zn_{0.2}S@MIL-101$(Cr) as a catalyst, 99.2% of methylene blue was mineralized within 30 min. Due to the synergistic effect of adsorption by the MIL-101(Cr) component and photocatalytic degradation provided by the $Cd_{0.8}Zn_{0.2}S$ component, the $Cd_{0.8}Zn_{0.2}S@MIL-101$(Cr) catalyst displayed superior photocatalytic performance relative to $Cd_{0.8}Zn_{0.2}S$ and MIL-101(Cr). Furthermore, $Cd_{0.8}Zn_{0.2}S@MIL-101$(Cr) possessed excellent stability during photodegradation and exhibited good reusability. The remarkable photocatalytic performance of $Cd_{0.8}Zn_{0.2}S@MIL-101$(Cr) is likely due to the effective transfer of electrons and holes at the heterojunction interfaces.

• 한국세라믹학회지
• /
• 제53권5호
• /
• pp.469-477
• /
• 2016

The application of nanomaterials for electrodes of intermediate temperature solid oxide fuel cells (SOFC) is introduced. In conventional SOFCs, the operating temperature is higher than 1073 K, and so application of nanomaterials is not suitable because of the high degradation rate that results from sintering, aggregation, or reactions. However, by allowing a decrease of the operating temperature, nanomaterials are attracting much interest. In this review, nanocomposite films with columnar morphology, called double columnar or vertically aligned nanocomposites and prepared by pulsed laser ablation method, are introduced. For anodes, metal nano particles prepared by exsolution from perovskite lattice are also applied. By using dissolution and exsolution into and from the perovskite matrix, performed by changing $P_{O2}$ in the gas phase at each interval, recovery of the power density can be achieved by keeping the metal particle size small. Therefore, it is expected that the application of nanomaterials will become more popular in future SOFC development.

• Advances in nano research
• /
• 제16권6호
• /
• pp.623-638
• /
• 2024

This study investigates the thermal post-buckling behavior of concrete eccentric annular sector plates reinforced with graphene oxide powders (GOPs). Employing the minimum total potential energy principle, the plates' stability and response under thermal loads are analyzed. The Haber-Schaim foundation model is utilized to account for the support conditions, while the transform differential quadrature method (TDQM) is applied to solve the governing differential equations efficiently. The integration of GOPs significantly enhances the mechanical properties and stability of the plates, making them suitable for advanced engineering applications. Numerical results demonstrate the critical thermal loads and post-buckling paths, providing valuable insights into the design and optimization of such reinforced structures. This study presents a machine learning algorithm designed to predict complex engineering phenomena using datasets derived from presented mathematical modeling. By leveraging advanced data analytics and machine learning techniques, the algorithm effectively captures and learns intricate patterns from the mathematical models, providing accurate and efficient predictions. The methodology involves generating comprehensive datasets from mathematical simulations, which are then used to train the machine learning model. The trained model is capable of predicting various engineering outcomes, such as stress, strain, and thermal responses, with high precision. This approach significantly reduces the computational time and resources required for traditional simulations, enabling rapid and reliable analysis. This comprehensive approach offers a robust framework for predicting the thermal post-buckling behavior of reinforced concrete plates, contributing to the development of resilient and efficient structural components in civil engineering.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 2007년도 학술발표회 논문집
• /
• pp.297-298
• /
• 2007

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.95-96
• /
• 2006

Surface modification of clay minerals has become increasingly important for improving the practical applications of clays such as polymeric nanocomposites. We used the copolymer as modifiers having phenyl components, and successfully developed a route for the preparation of amine functionalized polymer based on oligostyrene and its block copolymers. The oligo(St-co-VBC)s with controlled molecular weight were synthesized via nitroxide mediated polymerization method. We also successfully prepared organophilic layered silicates whose surface is covered with styrenic copolymers. Through the analysis of chemical structure and morphology, we concluded that copolymers were very effective organic modifiers to change the surface characteristics of layered silicates.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.1378-1381
• /
• 2006

The CNTs are the most extensively studied material which are characterized by the complete property of matter, structure, and the large thermal conductivity (Thermal conductivity of $CNTs\;{\sim}>2000W/mK$ vs. Thermal conductivity of Aluminum ${\sim}\;>204W/mK$). Thus, they are successfully applied to the various fields. However, due to the strong agglomeration caused by the van der waal's force, their applications are limited. In the present study, a new method for CNTs dispersion was developed by using the mechanical dispersion, acid treatment, and then Cu was coated. This process produces CNTs/Cu nanocomposite powders, whereby the CNTs are homogeneously located within the Cu powders. The thermal properties of the CNTs/Cu nanocomposite were investigated.

• 한국유변학회:학술대회논문집
• /
• 한국유변학회 2002년도 춘계 학술발표회 논문집
• /
• pp.125-128
• /
• 2002