• Korean Journal of Metals and Materials
• /
• v.49 no.9
• /
• pp.715-719
• /
• 2011

Nanopowders of $Fe_3N$ and Si were fabricated by high-energy ball milling. A dense nanostructured $12Fe-Si_3N_4$ composite was simultaneously synthesized and consolidated using a high-frequency induction-heated sintering method for 2 minutes or less from mechanically activated powders of $Fe_3N$ and Si. Highly dense $12Fe-Si_3N_4$ with a relative density of up to 99% was produced under simultaneous application of 80 MPa pressure and the induced current. The microstructure and mechanical properties of the composite were investigated.

• Korean Journal of Metals and Materials
• /
• v.49 no.8
• /
• pp.608-613
• /
• 2011

Nanopowders of Mo, Ti and Si were made by high-energy ball milling. A dense nanostructured $(Ti,Mo)Si_2$ compound was sintered by the pulsed current activated combustion method within two minutes from mechanically activated powder of Mo, Ti and Si. A highly dense $(Ti,Mo)Si_2$ compound was produced under simultaneous application of 80 MPa pressure and a pulsed current. The mechanical properties and micorostructure were investigated. The hardness and fracture toughness of the $(Ti,Mo)Si_2$ were $1030kg/mm^2$ and $4.9MPa{\cdot}m^{1/2}$, respectively. The mechanical properties were higher than monolithic $TiSi_2$.

• Korean Journal of Materials Research
• /
• v.28 no.6
• /
• pp.343-348
• /
• 2018

Recently, the properties of nanostructured materials as advanced engineering materials have received great attention. These properties include fracture toughness and a high degree of hardness. To hinder grain growth during sintering, it is necessary to fabricate nanostructured materials. In this respect, a high-frequency induction-heated sintering method has been presented as an effective technique for making nanostructured materials at a lower temperature in a very short heating period. Nanopowders of W and $Al_2O_3$ are synthesized from $WO_3$ and Al powders during high-energy ball milling. Highly dense nanostructured $W-Al_2O_3$ composites are made within three minutes by high-frequency induction-heated sintering method and materials are evaluated in terms of hardness, fracture toughness, and microstructure. The hardness and fracture toughness of the composite are $1364kg/mm^2$ and $7.1MPa{\cdot}m^{1/2}$, respectively. Fracture toughness of nanostructured $W-Al_2O_3$ is higher than that of monolithic $Al_2O_3$. The hardness of this composite is higher than that of monolithic W.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2012.11a
• /
• pp.86-87
• /
• 2012

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1998.08a
• /
• pp.81.3-81
• /
• 1998

• Journal of the Semiconductor & Display Technology
• /
• v.8 no.1
• /
• pp.7-12
• /
• 2009

The outgassing effects of selected vacuum materials on the vacuum characteristics were simulated by the $VacSim^{Multi}$ simulation tool. This investigation examined the feasibility of reliably simulating the outgassing characteristics of common vacuum chamber materials (aluminum, copper, stainless steel, nickel plated steel, Viton A). The optimum design factors for these vacuum systems were suggested based on the simulation results. The baking-out effects of the modeled systems and materials on the performance of the vacuum system were also analyzed. The simulation predicted that the overall outgassing effect was more significant in the TMP system than in the DP system and that the utilization of a booster pump has a greater effect on the evacuation time than on the ultimate pressure.

• Journal of the Korean Ceramic Society
• /
• v.48 no.5
• /
• pp.463-466
• /
• 2011

Wet foams formed through direct foaming were stabilized using various concentrations of amiphiphilic particles that could control pore size and porosity. These porous materials showed moderate strength upon compression with high porosity. Bubble size and wet foam stability were tailored by amphiphile concentration, particle concentration, contact angle, and pH of the suspension to obtain crack-free porous solid after sintering. Closed and open pores were obtained with sizes of 30~300 ${\mu}m$ and porosities of over 80%.

• Ceramist
• /
• v.22 no.2
• /
• pp.110-121
• /
• 2019

Triboelectric nanogenerators and piezoelectric nanogenerators are a spotlighted energy harvesting method that converts the wasted mechanical energy from the environment into usable electrical energy. In the case of triboelectric nanogenerators, researches have been mainly focused on high permittivity and flexible polymer materials, and in the case of piezoelectric nanogenerators, researches have been focused on ceramic materials exhibiting high polarization characteristics. Recently, many researches have been conducted to improve durability and power in various environments by using composite materials which have flexible properties of polymer, high permittivity, thermal resistance and high polarization properties of ceramics. This article reviews the energy harvesting studies reported about composites materials using ceramics and polymers.

• Applied Chemistry for Engineering
• /
• v.25 no.4
• /
• pp.414-417
• /
• 2014

LED scraps consisting of highly crystalline GaN and their leaching behavior are comprehensively investigated for hydro-metallurgical recovery of rare metals. Highly stable GaN renders the leaching of the LED scraps extremely difficult in ordinary acidic and basic media. More favorable state can be obtained by way of high temperature solid-gas reaction of GaN-$Na_2CO_3$ powder mixture, ball-milled thoroughly at room temperature and subsequently oxidized under ambient air environment at $1000-1200^{\circ}C$ in a horizontal tube furnace, where GaN was effectively oxidized into gallium oxides. Stoichiometry analysis reveals that GaN is completely transformed into gallium oxides with Ga contents of ~73 wt%. Accordingly, the oxidized powder can be suitably leached to ~96% efficiency in a boiling 4 M HCl solution, experimentally confirming the feasibility of Ga recycling system development.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.05a
• /
• pp.117-120
• /
• 2006

$TiOCl_2$를 중화시키고 과산화수소와 반응시켜 Ti peroxo 전구체를 수열합성법을 이용하여 autoclave 반응기 내에서 가열하여 $TiO_2$ 졸을 제조하였다. Autoclave 반응기 내에 압력을 가하면 브룩카이트상 $TiO_2$졸이 형성됨을 확인하였고, 중화과정에서 NaCl을 첨가하여 Ti 수산화물 격자 내에 Na 이온을 포획되어 브룩카이트상이 나타남을 알 수 있었다. Na 이온의 첨가량에 따라 브룩카이트 결정상 함량이 달라져 광촉매 활성도 달라짐을 브룩카이트상 $TiO_2$가 코팅된 박막의 기상벤젠 광분해 실험을 통해 확인하였고 미세구조, 결정성, 광흡수도률 측정하여 특성평가를 실시하였다.