• 접착 및 계면
• /
• 제6권4호
• /
• pp.1-6
• /
• 2005

본 실험에서는 화학적 표면처리된 탄화규소의 첨가가 탄화규소(SiC)/에폭시 복합재료의 critical strain energy release rate mode II ($G_{IIC}$) 특성에 미치는 영향에 대하여 알아보았으며, 표면처리된 SiC의 표면특성은 산 염기도와 FT-IR을 사용하여 알아보았다. 또한 복합재료의 기계적 계면물성은 $G_{IIC}$를 통하여 알아보았다. 실험결과, 산성 용액으로 표면처리한 SiC (A-SiC)의 표면 산도가 염기성(B-SiC) 또는 표면처리 하지 않은 SiC (V-SiC)보다 높으며, $G_{IIC}$의 크랙저항 특성은 A-SiC가 향상되었는데, 이러한 결과는 SiC 충전재와 에폭시 수지간의 분자간 계면결합력의 향상 때문으로 판단된다.

• 한국재료학회지
• /
• 제18권4호
• /
• pp.204-210
• /
• 2008

$1.5\;{\mu}m$-thick copper films deposited on silicon wafers were successfully bonded at $415^{\circ}C$/25 kN for 40 minutes in a thermo-compression bonding method that did not involve a pre-cleaning or pre-annealing process. The original copper bonding interface disappeared and showed a homogeneous microstructure with few voids at the original bonding interface. Quantitative interfacial adhesion energies were greater than $10.4\;J/m^2$ as measured via a four-point bending test. Post-bonding annealing at a temperature that was less than $300^{\circ}C$ had only a slight effect on the bonding energy, whereas an oxygen environment significantly deteriorated the bonding energy over $400^{\circ}C$. This was most likely due to the fast growth of brittle interfacial oxides. Therefore, the annealing environment and temperature conditions greatly affect the interfacial bonding energy and reliability in Cu-Cu bonded wafer stacks.

• Tribology and Lubricants
• /
• 제24권2호
• /
• pp.63-71
• /
• 2008

Friction and adhesion tests were conducted to investigate tribological characteristics of materials for MEMS/NEMS using atomic force microscope (AFM). AFM Si tips were chemically modified with a self-assembled monolayer (SAM) derived from trichlorosilane like octadecyltrichlorosilane (OTS) and (1H, 1H, 2H, 2H-perfluorooctyl) trichlorosilane (FOTS), and various materials, such as Si, Al, Au, Cu, Ti and PMMA films, were prepared for the tests. SAMs were coated on Si wafer by dipping method prior to AFM tip to determine a proper dipping time. The proper dipping time was determined from the measurements of contact angle, surface energy and thickness of the SAMs. AFM tips were then coated with SAMs by using the same coating condition. Friction and adhesion forces between the AFM Si tip modified with SAM and MEMS/NEMS materials were measured. These forces were compared to those when AFM tip was uncoated. According to the results, after coating OTS and FOTS, the friction and adhesion forces on all materials used in the tests decreased; however, the effect of SAM on the reduction of friction and adhesion forces could be changed according to counterpart materials. OTS was the most effective to reduce the friction and adhesion forces when counterpart material was Cu film. In case of FOTS, friction and adhesion forces decreased the most effectively on Au films.

• 접착 및 계면
• /
• 제11권3호
• /
• pp.120-125
• /
• 2010

UV-curable acrylic Pressure-sensitive adhesives (Acrylic PSAs) are used in many different parts in the world. A wafer manufacture process which is based on semiconductor industry is one thing. We have used acrylic PSAs whose thickness is different from $20{\mu}m$ to $30{\mu}m$ in wafer manufacture process so far. But as wafers become more thinner, acrylic PSAs are supposed to satisfy the requirements such as proper adhesion performance. The main purpose of this research is studying proper adhesion performance and UV-curing behavior of UV-curable acrylic PSAs with very thin thickness and then determining optimized conditions to raise the efficiency of thin wafer production. Acrylic PSAs contain 2-Ethylhexyl Acrylate (2-EHA), Acrylic Acid (AA) and Butyl Acrylate (BA). Ethyl acetate (EtAc) is used as solvent. The acrylic PSAs are obtained using solvent polymerization. Thickness of UV-curable acrylic PSAs is different from $10{\sim}30{\mu}m$. By peel strength and probe tack, adhesion performance and UV curing behavior of acrylic PSA are concerned.

• 방사선산업학회지
• /
• 제4권3호
• /
• pp.259-263
• /
• 2010

Carbon fibers are used as a reinforcement material in an epoxy matrix in advanced composites due to their high mechanical strength, rigidity and low specific density. An important aspect of the mechanical properties of composites is associated to the adhesion between the surface of the carbon fiber and the epoxy matrix. This paper aimed to evaluate the effects of electron beam irradiation on the physicochemical properties of carbon fibers to obtain better adhesion properties in resultant composite. Chemical structure and surface elements of carbon fiber were determined by FT-IR, elemental analysis and X-ray photoelectron spectroscopy, which indicated that the oxygen content increased significantly with increasing the radiation dose. Thermal stability of the carbon fibers was studied via the thermalgravimetric analysis. Surface morphology of carbon fiber was analyzed by scanning electron microscope. It was found that the degree of surface roughness was increased by electron beam irradiation.

• 방사선산업학회지
• /
• 제7권2_3호
• /
• pp.149-154
• /
• 2013

In this study, the simple preparation of poly(sodium 4-styrenesulfonate) (PSS)-patterned substrate via a selective ion irradiation was investigated to manipulate cell adhesion. PSS thin films spin-coated onto the hydrophobic polystyrene (PS) was patterned through masked 150 keV proton irradiation followed by developing with deionized water. The characteristics of the resulting PSS-patterned surfaces were investigated by using microscope, surface profiler, FT-IR, XPS, and contact angle analyzer. These analytical results revealed that the resolved $100{\mu}m$ PSS patterns were formed on the hydrophobic PS surface above the fluence of $1{\times}10^{15}ions\;cm^{-2}$ and the chemical structure, composition, and wettability of the PSS patterns were dependant on a fluence. Moreover, the results of the in-vitro cell culture and proliferation assay exhibited that H1299 cells preferentially adhered and proliferated onto the more hydrophilic PSS part of the PSS-patterned PS and the well-aligned cell patterns was formed on the PSS-patterned PS particularly at the fluence of $1{\times}10^{15}ions\;cm^{-2}$.

• 반도체디스플레이기술학회지
• /
• 제16권3호
• /
• pp.87-92
• /
• 2017

Poly(urethane acrylate) siloxane oligomers with Interpenetrating polymer networked nanoparticles were prepared to synthesize hard coating solution by reaction with isophorone diisocyanate(IPDI) of 1, 2, 3, 4 phr. The structures and molecular weights of the synthesized solutions were characterized by IR spectroscopy and gel permeation chromatography, respectively. In the cross-cut test for the adhesion, all the solutions showed good adhesion of 5B regardless of the content of IPDI and film thickness. The addition of 1 phr IPDI resulted in the best pencil hardness. The IPDI combined siloxane hard coating solution showed more flexibility than the siloxane solution. These results will yield the improvement in the siloxane solution using for plastic display plate.

• Journal of Periodontal and Implant Science
• /
• 제45권3호
• /
• pp.120-126
• /
• 2015

Purpose: With the significance of stable adhesion of alveolar bone and peri-implant soft tissue on the surface of titanium for successful dental implantation procedure, the purpose of this study was to apply microgrooves on the titanium surface and investigate their effects on peri-implant cells and tissues. Methods: Three types of commercially pure titanium discs were prepared; machined-surface discs (A), sandblasted, large-grit, acid-etched (SLA)-treated discs (B), SLA and microgroove-formed discs (C). After surface topography of the discs was examined by confocal laser scanning electron microscopy, water contact angle and surface energy were measured. Human gingival fibroblasts (hGFs) and murine osteoblastic cells (MC3T3-E1) were seeded onto the titanium discs for immunofluorescence assay of adhesion proteins. Commercially pure titanium implants with microgrooves on the coronal microthreads design were inserted into the edentulous mandible of beagle dogs. After 2 weeks and 6 weeks of implant insertion, the animal subjects were euthanized to confirm peri-implant tissue healing pattern in histologic specimens. Results: Group C presented the lowest water contact angle ($62.89{\pm}5.66{\theta}$), highest surface energy ($45{\pm}1.2mN/m$), and highest surface roughness ($Ra=22.351{\pm}2.766{\mu}m$). The expression of adhesion molecules of hGFs and MC3T30E1 cells was prominent in group C. Titanium implants with microgrooves on the coronal portion showed firm adhesion to peri-implant soft tissue. Conclusions: Microgrooves on the titanium surface promoted the adhesion of gingival fibroblasts and osteoblastic cells, as well as favorable peri-implant soft tissue sealing.

• 접착 및 계면
• /
• 제23권1호
• /
• pp.1-7
• /
• 2022

풍력블레이드가 대형화되면서 유리섬유 복합재료(GFRP)와 탄소섬유 복합재료(CFRP)를 혼용하여 제작하고 있고, 이 때 두 가지 이종재료 간의 접착특성에 대한 연구가 활발히 진행되고 있다. 본 연구에서는 에폭시 접착제 내 탄소나노튜브 함량 및 경화 시 습도의 차이에 따른 접착강도의 변화를 평가하였다. 탄소나노튜브의 함량이 다른 에폭시 접착제를 활용하여 GFRP와 CFRP를 접착하였고, 경화 시 습도에 따른 특성의 변화를 알아보기 위해 접착강도를 평가하였다. 탄소나노튜브 함량에 따른 변화를 알아보기 위해 접착제에 들어가는 탄소나노튜브의 함량을 0, 0.1, 0.3, 0.5, 1 wt%로 나누어 단일 랩 전단 시험을 진행하였고, 습도 조건에 따른 변화를 확인하기 위해 항온항습기로 습도를 20, 50, 80% 조건으로 나누어 접착제를 경화시킨 후 단일 랩 전단 시험을 진행하였다. 실험결과 에폭시 접착제에 탄소나노튜브를 넣음으로써 접착특성이 향상됨을 확인하였지만 함량이 과도하게 많을 때에는 접착력이 줄어드는 것을 확인하였다. 또한 습도가 증가할수록 접착특성이 변하지 않음을 확인할 수 있었다.

• Korean Chemical Engineering Research
• /
• 제55권1호
• /
• pp.34-39
• /
• 2017

본 실험은 방사선을 이용하여 유착방지용 Carboxymethyl cellulose sodium salt (CMC)/Porcine Cartilage Acellular Matrix (PCAM) 수화젤 필름에 대해 연구하였다. 방사선 조사시 CMC/PCAM의 농도 및 혼합비율에 따른 필름의 형태학적 구조, 젤화율, 젤강도, 팽윤도 등을 분석하였다. 방사선에 의해 가교된 CMC/PCAM 필름은 CMC 필름보다 물리적인 특성인 젤화율이 낮게 측정되었다. 또한, 가교된 CMC 필름보다는 CMC/PCAM 필름에서 인간 혈관내피세포의 부착 및 증식율이 감소하였다. 우리는 PCAM에 함유한 세포의 항부착 성분이 도입된 CMC/PCAM 필름과 CMC 필름은 세포의 접착 및 증식율을 낮추는 것을 확인하였다. 결론적으로, 본 연구에서는 방사선 가교된 CMC/PCAM 수화젤 필름은 유착방지 향상을 위한 유착방지제로서 응용이 기대된다.