• Journal of Korean Society of Water and Wastewater
• /
• v.13 no.4
• /
• pp.27-34
• /
• 1999

An experimental study on improvement of the paper-mill wastewater treatment using the pure oxygen activated sludge process was conducted. The effects of hydraulic retention time(HRT) and BOD loading on organic removal efficiency were investigated. The BOD removal efficiencies were above 90% under all examined HRTs except for HRT of 3 hours. The increase of HRT from 3 hours to 6 hours, and to 12 hours significantly improved BOD and COD removal efficiencies, respectively. However, additional increase of HRT did not affect organic removal efficiency. F/M ratio change at fixed HRT did not affect organic removal efficiency. However, F/M ratio investigated in this study(0.11~1.98kgBOD/kgMLVSS/day) was 5 times greater in maximum than that of conventional activated sludge process, which implies that pure oxygen activated sludge process can treat wastewater with high organic strength. Under the same HRT, the volumetric BOD loading change cause no effect on organic removal efficiency also.

• Journal of Power Electronics
• /
• v.12 no.1
• /
• pp.24-32
• /
• 2012

Direct duty-ratio PWM schemes for continuous fault tolerant operation of matrix converter-fed motor drives are presented. The proposed method features simple modular modulation structure based on per output phase concept, which requires no additional modification on the normal modulation schemes for fault-tolerant applications. Realizations of fault-tolerant strategy applied to different system configurations are also treated to enhance the system flexibility. The proposed method can be effectively applied to treat the motor open phase fault and converter switching device failure. Simulation and experimental results show the feasibility and validation of the proposed strategies.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.373-377
• /
• 2017

This paper presents a voice-activity detection (VAD) method for sound sequences with various SNRs. For real-time VAD applications, it is inadequate to employ a post-processing for the removal of burst clippings from the VAD output decision. To tackle this problem, building on the bi-level hidden Markov model, for which a state layer is inserted into a typical hidden Markov model (HMM), we formulated a robust method for VAD not requiring any additional post-processing. In the method, a forward-inference-ratio test was devised to detect the speech endpoints and Mel-frequency cepstral coefficients (MFCC) were used as the features. Our experiment results show that, regarding different SNRs, the performance of the proposed approach is more outstanding than those of the conventional methods.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.655-658
• /
• 1998

CMOS Reference Voltage Generator(RVG) is designed to possible CMOS process without additional process steps. It is possible to compensate the temperature of RVG by using PTAT(proportional to the absolute temperature). Temperature compensation is profitable because $\mun$ (electron mobility) is used. When VDD sweeps from 3V to 7V, variation ratio of Vref is 0.3125mV/V. Also temperature variation ratio of Vref is $047.1ppm/^{\circ}C$ during sweeping from $0^{\circ}C$ to $100^{\circ}C.$ Power Consumption is $50.3\muW.$

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.12
• /
• pp.1018-1027
• /
• 2003

This study treats the analysis of the performance and the design of plume abatement wet/dry cooling tower with dry type heat exchanger using a numerical method. A two-dimensional analysis is performed using the finite volume method for mechanical draft counterflow and crossflow tower. For a coupling problem between water and air system, a turbulent two phase flow is considered. Effectiveness-NTU method is used for modeling of the dry type heat exchanger. The parameter change simulations of the outer wall shape, the relative flowrate of air, and attachment of an air mixer are performed to examine the effect on plume abatement. It is found that if the relative air flowrate ratio and the adequate air mixer type are chosen well in addition to the ratio of water to air flowrate, the loss of the cooling capacity and the additional cost are reduced and the plume is abated.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.04b
• /
• pp.567-572
• /
• 1998

Structural behavior of R/C deep beams was investigated and compared to those of specimens with CFRP Grids. Test results show that the crushing of compression strut for the unstrengthened R/C deep beams is changed to the group of several diagonal cracks at mid-depth within the sheat span. Strengthened specimens grow to be more ductile after the redistribution of internal force on the CFRP Grids. The failure mode and variations of strains in the specimens are dependent on the shear span-to-depth ratio. The lower the shear span-to-depth ratio, the bigger failure load and the less variations in strain are observed. Additional anchorage of CFRP Grids does not only cause the improvement in the internal resistance, but also control the brittle shear failure of specimen after reaching the maximum loads.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.6
• /
• pp.2297-2306
• /
• 2015

This paper presents the development of a system with a reverse matrix converter (RMC) for permanent magnet synchronous motor (PMSM) drive and its effective control method. The voltage transfer ratio of the general matrix converter is restricted to a maximum value of 0.866, which is not suitable for applications whose source voltages are lower than the load voltages. The proposed RMC topology can step up the voltage without any additional components in the conventional circuit. Its control method is different from traditional matrix converter’s one, thus this paper proposes control schemes of RMC by means of controlling both the generator and motor side currents with properly designed control loop. The converter can have sinusoidal input/output current waveforms in steady state condition as well as a boosted voltage. In this paper, a hardware system with an RMC for a PMSM drive system is described. The performance of the system was investigated through experiments

• Journal of the Korean Society of Combustion
• /
• v.10 no.1
• /
• pp.27-36
• /
• 2005

In this study, we investigated characteristics of a gas flow and a combustion property during the combustion of a RDF in a pyrolysis melting incinerator with disposal rate of 30 kg/hr. The RDF was pyrolyzed through the pyrolysis chamber at $600^{\circ}C$ of the chamber surface without oxygen condition. The pyrolysis gas was injected in the combustion chamber. It was burned by means of the staged combustion that was injecting secondary and tertiary air in the combustor. We measured the temperatures and the gas components in the combustion chamber while maintaining the air-fuel ratio of 1.3. Finally, we confirm that additional air injection, secondary and tertiary air ratio, was the most important factor to reduce NOx.

• Journal of information and communication convergence engineering
• /
• v.18 no.2
• /
• pp.100-105
• /
• 2020

With the advent of the 5G era, the rapid growth in demand for mobile content services has increased the need for additional backhaul investment. To meet this demand, employing a content delivery network (CDN) and optical access solution near the last mile has become essential for the configuration of 5G networks. In this paper, a cache-enabled architecture using the passive optical network (PON) is presented to serve video on demand (VoD) for users. For efficient use of mobile backhaul, I propose a request deduplication scheme (RDS) that can provide all the requested services missed in cache with minimum bandwidth by eliminating duplicate requests for movies within tolerable range of the quality of service (QoS). The performance of the proposed architecture is compared with and without RDS in terms of the number of requests arriving at the origin server (OS), hit ratio, and improvement ratio according to user requests and cache sizes.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.1104-1113
• /
• 2010

In order to reduce negative skin friction uses bitumen most plentifully. But, Bitumen is expensive very of 1.5 or more times of pile material expense. The bitumen will be able to substitute it is nescessary. It was researched that it would be able to bitumen substitutions from in products which is produced from domestic in this study. This was composed with most bentonite, added some cement. When it is used this product in the model test, the reduction ratio appear of 85% or more. In this result, this product as the reduction material is confirmed that has enough ability. Additional research leads, the product according to pile construction method must verify the reduction effect of negativ skin friction in field test.