• ETRI Journal
• /
• 제31권2호
• /
• pp.234-236
• /
• 2009

We present a novel operational amplifier preset technique for a switched-capacitor circuit to reduce the acquisition time by improving the slewing. The acquisition time of a variable gain amplifier (VGA) using the proposed technique is reduced by 30% compared with a conventional one; therefore, the power consumption of the VGA is decreased. For additional power reduction, a programmable capacitor array scheme is used in the VGA. In the 0.13 ${\mu}m$ CMOS process, the VGA, which consists of three-stages, occupies 0.33 $mm^2$ and dissipates 19.2 mW at 60 MHz with a supply voltage of 1.2 V. The gain range is 36.03 dB, which is controlled by a 10-bit control word with a gain error of ${\pm}0.68$ LSB.

• The Korean Journal of Ceramics
• /
• 제5권2호
• /
• pp.104-109
• /
• 1999

Rheological properties of dense slurries over 45 volume % with different monosaccharides and disaccharides were checked in order to increase the solid content of dense slurries without sacrificing plasticity using creep testing method. Strain in creep test showed good correlations with Burger model which is expressed as an exponential function of time. Among several monosaccharides and disaccharides studied here, fructose and sucrose were most effective in making dense alumina slurry plastic than other monosaccharides and disaccharides like glucose, galactose, xyloss and maltose. In the case of dense alumina slurry with sucrose, sucrose content or additional water content enhanced to the plasticity of the slurries.

• 분석과학
• /
• 제18권6호
• /
• pp.520-528
• /
• 2005

Two biological Certified Reference Materials (CRMs), KRISS 108-04-001 (oyster tissue) and 108-05-001 (water dropwort stem), were prepared by Korea Research Institute of Standards and Science (KRISS)during FY '01. The certified values of these materials had been determined by Isotope Dilution Mass Spectrometry (IDMS) for six elements (Cd, Cr, Cu, Fe, Pb and Zn). Additional analytical works are now progressing to certify the concentrations of a number of the environmental and nutrimental elements in these CRMs. The certified values in a CRM are usually determined by using a single primary method with confirmation by other method(s) or using two independent critically-evaluated methods. Instrumental Neutron Activation Analysis (INAA) plays an important role in the determination of certified values as it can eliminate the possibility of common error sources resulting from sample dissolution. In this study INAA procedure was used in determination of 23 elements in these two biological CRMs to acquire the concentration information and the results were compared with KRISS certified values.

• 식물분류학회지
• /
• 제51권4호
• /
• pp.353-362
• /
• 2021

The chloroplast genome of Glycyrrhiza uralensis Fisch was sequenced to investigate intraspecific variations on the chloroplast genome. Its length is 127,689 bp long (34.3% GC ratio) with atypical structure of chloroplast genome, which is congruent to those of Glycyrrhiza genus. It includes 110 genes (76 protein-coding genes, four rRNAs, and 30 tRNAs). Intronic region of ndhA presented the highest nucleotide diversity based on the six G. uralenesis chloroplast genomes. A total of 150 single nucleotide polymorphisms and 10 insertion and deletion (INDEL) regions were identified from the six G. uralensis chloroplast genomes. Phylogenetic trees show that the six chloroplast genomes of G. uralensis formed the two clades, requiring additional studies to understand it.

• 구강회복응용과학지
• /
• 제37권3호
• /
• pp.111-122
• /
• 2021

목적: 5Y-ZP의 세가지 층 간 굽힘강도, 투과도를 비교하고 추가적인 소성이 미치는 영향을 연구하고자 하였다. 연구 재료 및 방법: 소결한 지르코니아 블록을 세가지 층에 따라 분리한 후 원형 디스크 시편을 제작하였다. 시편의 직경은 15.0 mm이며, 2축굽힘강도와 투과도를 측정하기 위한 시편의 두께는 각각 1.2 mm와 1.0 mm이다. 시편들을 추가적인 소성 횟수(0, 1, 3번)에 따라 세 군으로 분류한 후 추가적인 소성은 900℃ 이하의 온도에서 퍼니스를 사용하여 소성 횟수에 따라 시행하였다. 만능재료시험기와 자외선-가시광선 분광광도계를 사용하여 2축굽힘강도와 투과도를 측정하였다. 상의 변화를 관찰하기 위해 X선 회절 분석을 시행하였다. 측정값은 One-way ANOVA, Tukey HSD test를 통하여 분석하였다(α = 0.05). 결과: 층 간 2축굽힘강도는 유의한 차이가 없었지만(P > 0.05) 투과도는 유의한 차이가 있었다(P < 0.05). 절단 및 전이층은 1번의 추가적인 소성 후 굽힘강도가 유의하게 감소하였으며, 3번의 추가적인 소성 후에는 모든 층의 굽힘강도가 소성 전과 비교하여 유의하게 감소하였다. 몸체 층을 제외한 나머지 층들은 추가적인 소성 후에 투과도가 유의하게 감소하였다. 모든 그룹의 X선 회절 분석 결과는 유사하였다. 결론: 5Y-ZP의 세 층은 투과도의 차이만 존재하였다. 추가적인 소성은 각 층의 굽힘강도와 투과도에 다른 영향을 미쳤으나 상전이는 발견되지 않았다.

• 토지주택연구
• /
• 제4권4호
• /
• pp.425-434
• /
• 2013

중소기업청은 일정규모 이상의 공공건설사업에 대해 일반공사와 의무적으로 분리하여 직접 구매해야 하는 123개 공사용자재 제품군을 지정하고, 법에서 정한 바에 따라 발주기관이 자재를 직접 구매하여 수급인에게 공급하도록 하고 있다. 본 연구에서는 이러한 공사용자재 직접구매제도 하에서 공공아파트 건설 현장에 투입되는 지급자재가 지니는 다양한 특성과 관리요인을 발주자 입장에서 종합적으로 고려하여, 주요관리대상 자재를 파악하고, 자재 조달 프로세스를 기반으로 이들에 대한 적정 관리 방안을 제시하였다. 즉, 조달경로, 현장특화정도, 입주자 요구수준, 업체 책임범위, 납품분할정도, 현장작업 요구도, 부속자재 필요도, 검수조건 등 지급자재가 가지는 주요 관리요인을 적용하여 공공아파트 건설사업에 적용되는 43개 직접 구매 대상품목의 조달관리부담을 평가한 결과, 상대적으로 높은 조달관리노력이 요구되는 주요관리대상그룹에는 목재창호, 알루미늄창호, 승강기, 목재마루재, 레미콘, 타일, 합성수지창호가 포함되었고, 그 중 알루미늄창호와 타일은 집중관리대상으로 분류되었다. 나아가 직접구매제도의 영향에 따른 집중관리대상 자재에 대한 대응방안은 발주자 입장에서 실태, 문제점, 관리측면의 주요 고려사항을 반영하여 작성하였으며, 실질적 수량 산출, 명확한 발주세부조건 정비, 생산 전후 활동 활성화, 하자보수 물량 확보, 공종별 간섭 사전 협의 및 해소 등이 필수적인 관리활동으로 나타났다.

• Structural Engineering and Mechanics
• /
• 제63권6호
• /
• pp.713-723
• /
• 2017

As a new type of ballastless track, longitudinal continuous slab track (CST) has been widely used in China. It can partly isolate the interaction between the ballastless track and the bridge and thus the rail expansion device would be unnecessary. Compared with the traditional track, CST is composed of multi layers of continuous structures and various connecting components. In order to investigate the performance of CST on a long-span bridge, the spatial finite element model considering each layer of the CST structure, connecting components, bridge, and subgrade is established and verified according to the theory of beam-rail interaction. The nonlinear resistance of materials between multilayer track structures is measured by experiments, while the temperature gradients of the bridge and CST are based on the long-term measured data. This study compares the force distribution rules of ballasted track and CST as respectively applied to a long span bridge. The effects of different damage conditions on CST structures are also discussed. The results show that the additional rail stress is small and the CST structure has a high safety factor under the measured temperature load. The rail expansion device can be cancelled when CST is adopted on the long span bridge. Beam end rotation caused by temperature gradient and vertical load will have a significant effect on the rail stress of CST. The additional flexure stress should be considered with the additional expansion stress simultaneously when the rail stress of CST requires to be checked. Both the maximum sliding friction coefficient of sliding layer and cracking condition of concrete plate should be considered to decide the arrangement of connecting components and the ultimate expansion span of the bridge when adopting CST.

• 한국문헌정보학회지
• /
• 제38권4호
• /
• pp.149-166
• /
• 2004

이 연구는 한국목록규칙 제4판을 중심으로 일본목록규칙, 영미목록규칙, 국제표준서지기술법의 판사항에 대한 규정을 비교 분석한 것이다. 규칙들간에 미묘한 차이는 있지만 판사항에 대한 특징을 요약하면 아래와 같다. (1) 서지기술에 있어 판과 쇄의 개념을 구별하면서 판의 개념을 매우 포괄적으로 적용하고 있다. 즉, 대체로 내용의 변화가 있거나. 내용의 변화는 없더라도 크기나 활자를 달리하면 새로운 판으로 표시하며, 그렇지 않은 경우는 새로이 발행하더라도 쇄로 표시한다. (2) 판사항의 기술요소는 크게 판표시, 특정 판의 책임표시 부차적 판표시, 그리고 부차적 판의 책임표시와 같이 4개요소로 규정하고 있으며, 대등 판표시는 대개 임의규정으로 되어 있다. (3) 전자자료의 경우, 전자자료의 내용과 기능에 대한 특정 버전을 나타내는 표시는 판으로 표시하는 반면 전자자료의 기능을 수행하는데 필요한 소프트웨어 환경은 판으로 표시하지 않는다. (4) 판에 대한 대등책임표시, 부차적 대등판표시 및 책임표시는 임의규정으로 하거나 판사항에 표시하지 않는다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제19권2호
• /
• pp.25-28
• /
• 2017

In superconducting coil applications particularly in wet wound coils, coated conductor (CC) tapes are subjected to different type of stresses that could affect its electromechanical transport property. These include hoop stress acting along the length of the CC tape and the Lorentz force acting perpendicular to the CC tape's surface. Since the latter is commonly associated with the delamination problem of multi-layered REBCO CC tapes, more understanding and attention on the delamination phenomena induced in the case of coil applications are needed. Difference on the coefficient of thermal expansion (CTE) of each constituent layer of the CC tape, the bobbin, and the impregnating materials is the main causes of delamination in CC tapes when subjected to thermal and mechanical cycling. In the design of degradation-free superconducting coils, therefore, characterization of the delamination behaviors including mechanism and strength in the multi-layered REBCO CC tapes becomes a critical issue. Various trials to increase the delamination strength by improving interface characteristics at interlayers have been performed. In this study, in order to investigate the influences of laser cleaning and Ag annealing treated at the substrate side surface, transverse tensile tests were conducted under different sample configurations using $4.5mm{\times}8mm$ upper anvil. The mechanical delamination strength of differently processed CC samples was examined at room temperature (RT). As a result, the Sample 1 with the additional laser cleaning and Ag annealing processes and the Sample 2 with additional Ag annealing process only showed higher mechanical delamination strength as compared to the Sample 3 without such additional treatments. Sample 3 showed quite different behavior when the loading direction is to the substrate side where the delamination strength much lower as compared to other cases.

• The Journal of Advanced Prosthodontics
• /
• 제12권5호
• /
• pp.322-328
• /
• 2020

PURPOSE. This study evaluated the shear bond strength between 3D printed provisional resin and conventional provisional resin depending on type of conventional provisional resin and different surface treatments of 3D printed resin. MATERIALS AND METHODS. Ninety-six disc-shaped specimens (Ø14 mm × 20 mm thickness) were printed with resin for 3D printing (Nextdent C&B, Vertex-Dental B. V., Soesterberg, Netherlands). After post-processing, the specimens were randomly divided into 8 groups (n=12) according to two types of conventional repair resin (methylmethacrylate and bis-acryl composite) and four different surface treatments: no additional treatment, air abrasion, soaking in methylmethacrylate (MMA) monomer, and soaking in MMA monomer after air abrasion. After surface treatment, each repair resin was bonded in cylindrical shape using a silicone mold. Specimens were stored in 37℃ distilled water for 24 hours. The shear bond strength was measured using a universal testing machine at a crosshead speed of 0.5 mm/min. Failure modes were analyzed by scanning electron microscope. Statistical analysis was done using one-way ANOVA test and Kruskal-Wallis test (α=.05). RESULTS. The group repaired with bis-acryl composite without additional surface treatment showed the highest mean shear bond strength. It was significantly higher than all four groups repaired with methylmethacrylate (P<.05). Additional surface treatments, neither mechanical nor chemical, increased the shear bond strength within methylmethacrylate groups and bis-acryl composite groups (P>.05). Failure mode analysis showed that cohesive failure was most frequent in both methylmethacrylate and bis-acryl composite groups. CONCLUSION. Our results suggest that when repairing 3D printed provisional restoration with conventional provisional resin, repair with bis-acryl composite without additional surface treatment is recommended.