• Tribology and Lubricants
• /
• 제13권2호
• /
• pp.96-104
• /
• 1997

This paper was focused on the wear characteristics of ion-nitrided metal and with ion-nitride processing, which is basically concerned with the effects of carbon content in workpiece and added carbon content gas atmosphere on the best wear performance. Increased carbon content in workpiece increases compound layer thickness, but decreases diffusion layer thickness. On the other hand, a small optimal amount of carbon content in gas atmosphere increase compound layer thickness as well as diffusion layer thickness and hardness. Wear tests show that the compound layer of ion-nitrided metal reduces wear rate when the applied wear load is small. However, as the load becomes large, the existence of compound layer tends to increase wear rate. Compressive residual stress at the compound layer is the largest at the compound layer, and decreases as the depth from the surface increases. It is found in the analysis that under small applied load, the critical depth where voids and cracks may be created and propagated is located at the compound layer, so that the adhesive wear is created and the existence of compound layer reduces the amount of wear. When the load becomes large, the critical depth is located below the compound layer and delamination, which may explained by surface deformation, crack nucleation and propagation, is created and the existence of compound layer increases wear rate. For the compound layer, at added carbon contents of 0 percent and 0.5 at. percent, the $\varepsilon$ monophase is predominant. But at 0.7 at. percent added carbon, the $\varepsilon$ monophase formation tends to be severely inhibited and r' and $Fe_3C$ polyphase formation becomes dominant. This increased hard $\varepsilon$ phase layer was observed to be more beneficial in reducing friction and wear.

• 오토저널
• /
• 제4권2호
• /
• pp.35-46
• /
• 1982

This paper deals with residual stress characteristics of ion-nitrided metal which is primarilly concerned with the effects of added carbon content in gas atmosphere. A small optimal amount of carbon content in gas atmosphere increase compound layer thickness, as well as to increase diffusion layer thickness and hardness. The residual stress and deflection of the specimens was measured in various elevated temperature at the surface of ion-nitrided metal and the internal stress distribution was calculated. It is found that compressive residual stress at the compound layer is largest at the compound layer, and decreases as the depth from the surface increases.

• 대한기계학회논문집
• /
• 제7권1호
• /
• pp.19-27
• /
• 1983

This paper deals with hardness and wear characteristics of ion-nitrided metal, and with ion-nitride processing which is concerned with the effects of added carbon content in gas atmosphere. A small optimal amount of carbon content in gas atmosphere increase compound layer thickness, as well as to increase diffusion layer thickness and hardness, and reduces wear rate when the applied wear load is small. It is found in the analysis that under small applied wear load, the critical depth where voids and cracks may be created and propagated is located at the compound layer, so that the abrasive wear where hardness is an important factor, is created and the existence of compound layer reduces the amount of wear. When the load becomes large, the critical depth is located below nucleation and propagation, is created and the existence of compound layer increase wear rate.

• 통합자연과학논문집
• /
• 제12권4호
• /
• pp.116-121
• /
• 2019

This experiment is to evaluate the physical properties of the hydrogel lens with the addition of carbon-based nanomaterials, Graphene oxide and Carbon nanotube, and to confirm the improvement of strength. Hyaluronic acid, a hydrophilic substance, was used as an additive by using HEMA (2-hydroxyethyl methacrylate) and ethylene glycol dimethacrylate (EGDMA) as a base monomers. Graphene oxide and two types of Carbon nanotubes(Amide functionalized and Carboxilic acid functionalized) were added 0.1%, 0.3%, 0.5%, respectively, and the physical properties were analyzed by measuring water content, refractive index, breaking strength and SEM image. In the case of the sample added with each carbon nano material, the water content tended to increase for all three materials. The breaking strength tended to increase in Graphene oxide and Carbon nanotube; Carboxilic acid functionalized, but in the case of Carbon nanotube; amide fuctionalized, the breaking strength tended to decrease. However, Carbon nanotube; amide fuctionalized had the highest breaking strength among the three nano materials. Thus, the addition of certain carbon nanomaterials seems to be appropriate for improving the strength of hydrogel lenses.

• 한국분말재료학회지
• /
• 제1권1호
• /
• pp.27-34
• /
• 1994

Commercial pure iron powder and iron powder of coated 0.45% phosphorus were mixed with graphite powder in dry mixer to control carbon content from 0 wt% to 0.8 wt%. Mixed powder was pressed in the mould under the pressure of 510 MPa. Compacts were sintered at 118$0^{\circ}C$ for 40 min. in cracked ammonia gaseous atmosphere. Some of these sintered specimens were quenched in oil, and tempered in Ar gas. All of these specimens were investigated for microstructure, density and hardness in relation to coated phosphorus and carbon content. The results obtained were as follows: (1) The microstructure of the sintered speciments revealed that the amount of pearlite was increased with increasing C content but decreased by P-addition. (2) The P-addition affected the microstructure of pores in which the pore shape became round and its mean size was decreased by P-addition. (3) After tempering of sintered specimens the structure of pearlite was changed from fine structure to coarse one in P added specimen. (4) Hardness was higher in P added specimens.

• 한국분말재료학회지
• /
• 제6권1호
• /
• pp.62-68
• /
• 1999

The effects of the carbon content ranging from 17.5 to 21.0 wt.% in TiC-30vol.% $Ni_3Al$ cenmet and the $Mo_2C$ content raging from 0 to 30 wt.% in TiC-20 vol.% $Ni_3Al$ cermet were investigated in the relation to the microstures and harbness. The speciment were sintered at 140$0^{\circ}C$, 143$0^{\circ}C$ and 145$0^{\circ}C$ for 60minutes. The results were summarized as follows; 1) The shrinkages and relative densitites of the specimens were incrased up to 20.0 wt.% C and then decreased. 2) The grains of TiC were almost the same size with the different content of carbon. Free carbons were appeared on the microstrures when carbon was added over 20.5 wt.% while TiC and $Ni_3Al$l were formed when carbon was added below 20.0 wt.%; 3) The lattice parameters of the $Ni_3Al$ and TiC phases were increased up to 20.5 wt.% C, and then saturated. 4) The hardess was increased up to 20.0 wt.% C, and then decreased. 5) The $Mo_2C$ made the TiC grains fine and the surrounding structure around TiC gains. 6) The micropores were decreased with increasing the binder and the sintering temperature. 7) The lattice parameter of the $Ni_3Al$l ana TiC were almost the samp up to 10 wt.% $Mo_2C$ and then decreased. 8) The hatdness was increased up to 5wt.% $Mo_2C$ and then decreased owing to the micrpores. 9) The more the binder phase, the higher the relative density and the proper $Mo_2C$ amount of $TiC-Ni_3Al$ cermets were obtained.

• Carbon letters
• /
• 제10권4호
• /
• pp.335-338
• /
• 2009

In this work, the effect of co-carbon fillers on the electrical and mechanical properties of epoxy nanocomposites was investigated. The graphite nanosheets (GNs) and multi-walled carbon nanotubes (MWNTs) were used as co-carbon fillers. The results showed that the electrical conductivity of the epoxy nanocomposites showed a considerable increase upon an addition of MWNTs when GNs were fixed at 2 wt.%. This indicated that low content GNs formed the bulk conductive network and then MWNTs added were intercalated between the GN layers, resulted in the formation of additional conductive pathway. Furthermore, the flexural strength of the epoxy nanocomposites was enhanced with increasing the MWNT content. It was probably attributed to the flexible MWNTs compared with rigid GNs, resulted in the enhancement of the mechanical properties.

• 한국연초학회지
• /
• 제17권1호
• /
• pp.62-67
• /
• 1995

Deliveries of tar, nicotine and carbon monoxide in mainstream smoke decreased with increment of exogenous potassium content of tobacco. Potassium malate was more effective than potassium nitrate, potassium carbonate, potassium citrate and potassium oxalate for the reduction of carbon monoxide, but potassium nitrate was more effective than potassium palate, potassium carbonat, potassium citrate and potassium oxalate for the reduction of carbon in the case of nicotine. Puff count and burning rate were slightly changed with added potassium salts.

• 인간식물환경학회지
• /
• 제23권5호
• /
• pp.537-544
• /
• 2020

Background and objective: Artemisia argyi has a long history as an effective treatment for various diseases. The detection of environmental pollutant benzo(a)pyrene, a known human carcinogen, in the leaves of Artemisia argyi is cause for concern. For medicinal plant extracts, both a reduction of benzo(a)pyrene as well as the maintained effectiveness of the compound are important. Therefore, in this study, we propose an optimized process for the addition and filtration of activated carbon to reduce benzo(a)pyrene and change the contents of the indicating substance(jaceosidine and eupatilin). Methods: Artemisia argyi EtOH extract containing 36 ppb of benzo(a)pyrene was added to 0.1, 0.5, 1.0, and 1.5% (w/w) of activated carbon for 120 min and filtered using an activated carbon filter 1, 2, 3, and 5 times respectively. The content of benzo(a)pyrene and indicating substances in Artemisia argyi extract were then measured with high performance liquid chromatography (fluorescence and UV detectors). Results: As the amounts of activated carbon powder and filtering cycles increased, the content of benzo(a)pyrene in the Artemisia argyi extract decreased. However, when activated carbon powder 1.5% was added to the extract, and when the activated carbon filter was filtered five times, the results were reduced by 15% and 30~40% respectively. The optimal extraction condition for reducing benzo(a)pyrene was adding 1.5% of activated carbon powder. This resulted in reducing benzo(a)pyrene by 83% and indicating substances by about 4%. Conclusions: Here we present a process for reducing benzo(a)pyrene in Artemisia argyi extract using activated carbon to reduce toxicity and minimize the loss of active ingredients. This approach has potential application within a manufacturing process of various medicinal plant extracts.

• Mycobiology
• /
• 제42권1호
• /
• pp.59-65
• /
• 2014

Entomopathogenic fungi are promising pest-control agents but their industrial applicability is limited by their thermosusceptibility. With an aim to increase the thermotolerance of Isaria fumosorosea SFP-198, moisture absorbents were added to dried conidial powder, and the relationship between its water potential and thermotolerance was investigated. Mycotized rice grains were dried at $10^{\circ}C$, $20^{\circ}C$, $30^{\circ}C$, and $40^{\circ}C$ and the drying effect of each temperature for 24, 48, 96, and 140 hr was determined. Drying for 48 hr at $10^{\circ}C$ and $20^{\circ}C$ reduced the moisture content to < 5% without any significant loss of conidial thermotolerance, but drying at $30^{\circ}C$ and $40^{\circ}C$ reduced both moisture content and conidial thermotolerance. To maintain thermotolerance during storage, moisture absorbents, such as calcium chloride, silica gel, magnesium sulfate, white carbon, and sodium sulfate were individually added to previously dried-conidial powder at 10% (w/w). These mixtures was then stored at room temperature for 30 days and subjected to $50^{\circ}C$ for 2 hr. The white carbon mixture had the highest conidial thermotolerance, followed by silica gel, magnesium sulfate, and then the other absorbents. A significant correlation between the water potential and conidial thermotolerance was observed in all conidia-absorbent mixtures tested in this study (r = -0.945). Conidial thermotolerance in wet conditions was evaluated by adding moisturized white carbon (0~20% $H_2O$) to conidia to mimic wet conditions. Notably, the conidia still maintained their thermotolerance under these conditions. Thus, it is evident that conidial thermotolerance can be maintained by drying mycotized rice grains at low temperatures and adding a moisture absorbent, such as white carbon.