• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.615-619
• /
• 2004

A new asymmetrical zero voltage switching (ZVS) active clamp forward converter is proposed. Since the ripple current of secondary inductor plays a key role in the ZVS operation of main power switch, the proposed converter shows an excellent ZVS performance. The synchronous rectification is employed to reduce the rectification loss. The operational principle and ZVS analysis are presented. Experimental results demonstrate that the proposed converter can achieve an excellent ZVS performance throughout all load conditions and the significant improvement in the efficiency for the 100W(5V,20A) prototype converter.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.135-138
• /
• 2009

Quality evaluation of laser welded MCFC separator panels with large active area was performed. Lap joint was applied to produce stable air-tight seam weld by employing Nd:YAG laser. Results showed that surface contamination played a key role to form weld defects at the joint interface. However, there was no evidence that weld width at the lap joint changed after the stack operation time of 2,890h. Test results also revealed that the reinforcement values which were measured on the weld line after long time operation, were stable.

• Journal of the Korean Ceramic Society
• /
• v.35 no.1
• /
• pp.33-40
• /
• 1998

A MgO-CaO-based coating material for ferrous melt refining is applied to the tundish operation for mol-ten steel having low carbon. The changes in the total oxygen content insoluble aluminum content and the content of inclusions in molten steel during tundish operation were measured at the pouring part strand of tundish and mold. On the basis of the experimental results the interfacial reaction occurring between the coating materials and the molten steel in tundish was discussed and compared with the theoretical con-sideration. It is concluded that interfacial reaction is not active at the strand part of tundish but is active at the pouring part because of the turbulent flow in the molten steel.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.8
• /
• pp.551-556
• /
• 2000

A zero-voltage-switching(ZVS) programmable power supply employing the ZVS active clamp forward converter is suggested. Through the analysis on operation region of the supply, the constant power region and the maximum current limit region are clearly identified. Furthermore, the duty ratio range corresponding to the variation range of the output voltages and the control scheme at the minimum duty ration region are presented. Finally, in order to vefity the validity of the operation for the proposed power supply, experimental evaluation results obtained on an 1kW prototype power supply for the 198~242VAC input voltage range(220VAC$\pm$10%), the 0~25V output voltage range, and the 100kHz switching frequency are presented.

• Journal of Electrical Engineering and Technology
• /
• v.3 no.2
• /
• pp.254-262
• /
• 2008

This paper presents an active use of doubly-fed induction-generator(DFIG)-based variable-speed wind-turbine for voltage control in power system operation. For reasonable simulation studies, a detail dynamic model of a DFIG-based wind-turbine grid-connected system is presented. For the research objective, an innovative reactive power control scheme is proposed that manipulates dynamically the reactive power from the voltage source converter(VSC) with taking into account its operating state and limits.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.1
• /
• pp.9-15
• /
• 2021

In multi-string light-emitting diode (LED) driver system, current balancing is crucial because the brightness of LED is directly related to its forward current. This paper presents a novel LED current balancing topology using current-fed Z-source converter. With the proposed structure, currents flowing through two LED strings are automatically balanced owing to the charge-balance condition on capacitors. Operation of the proposed converter is simple and the proposed converter uses only one active switch and one diode. Moreover, low-side gate driving can be used to operate the active switch. To verify the operation of the proposed LED current balancing converter, a prototype is built and tested with different numbers of LEDs.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.5
• /
• pp.350-354
• /
• 2003

This study proposes a new self-driven active clamp forward converter eliminating the extra drive circuit for the active clamp switch. The converter used the auxiliary winding of the power transformer to drive the active clamp switch and a simple R-C circuit to get the dead time between the two switches. The operation principle was presented and experimental results were used to verify theoretical predictions. A 100-W (5V/20A) prototype converter built that only exhibited 1.5-turn winding number in the auxiliary winding was sufficient to drive the active clamp switch on the input of 50V. Finally, the measured efficiency of the converter was presented and the maximum efficiency of 91% was obtained.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.5
• /
• pp.477-484
• /
• 2013

This paper proposes a novel switching method of active clamp snubber for efficiency improvement of PV module integrated converter(MIC) system. Recently, MIC solar system is researched about the efficiency and safety. PV MIC system is used active clamp method of snubber circuit for the price and reliability of the system. But active clamp snubber circuit has the disadvantage that system efficiency is decreased for switch operating time because of heat loss of resonant between snubber capacitor and leakage inductance. To solve this problem, this paper proposes a novel switching method of the active clamp. The proposed method is a technique to reduce power consumption by reducing the resonance of the snubber switch operation time and through simulations and experiments proved the validity.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.9
• /
• pp.31-37
• /
• 2004

We have proposed a design methodology for large active-area single-mode VCSELS, which have higher reliability and output power, and are well-suited for high-speed operation. The key idea underlying the design methodology is to reduce the effective index difference between active and cladding regions by controlling the thickness and position of the oxide layer. The idea is confirmed by the self-consistent effective index method. By placing the oxide layer position properly, we can increase the radius of the oxide aperture for single-mode operation by 3 times.

• Journal of Biomedical Engineering Research
• /
• v.29 no.3
• /
• pp.179-186
• /
• 2008

This paper presents a portable tele-assessment system designed for remote evaluation of the hypertonic elbow joint of neurologically impaired patients. A patient's upper limb was securely strapped to a portable limb-stretching device which is connected through Internet to a portable haptic device by which a clinician remotely moved the patient's elbow joint and felt the resistance from the patient. Elbow flexion angle and joint torques were measured from both master and slave devices and bilaterally fed back to their counterparts. In order to overcome problems associated with the network latency, two different tele-operation schemes were proposed depending on relative speed of tasks compared to the amount of time delay. For slow movement tasks, the bilateral tele-operation was achieved in real-time by designing control architectures after causality analysis. For fast movement tasks, we used a semi-real-time tele-operation scheme which provided the clinicians with stable and transparent feeling. The tele-assessment system was verified experimentally on patients with stroke. The devices were made portable and low cost, which makes it potentially more accessible to patients in remote areas.