• Journal of Biosystems Engineering
• /
• v.39 no.1
• /
• pp.57-67
• /
• 2014

Purpose: The modern IT can give enormous impacts on the agricultural production and consumption. However, farmer's ability to use IT devices has been known as one of the critical factors on success of IT in agriculture. This survey study was performed to evaluate the informatization status of farmers and to draw a strategy to develop and distribute a ubiquitous agricultural information system. Methods: A survey questionnaire with 19 questions on the degree of IT devices such as computers and smartphones and their utilization were developed. The survey was questioned 3 groups of farmers in Gyounggi Province and analyzed statistically by the ${\chi}^2$ test. Results: The order of IT devices distribution were computers, smartphones, smart TVs and tablet PCs in all groups. The ratios of ownerships of the devices are 97.7, 78.6%, 31.4%, 17.8% respectively. The active farmers in this survey showed higher informatization level than that of native and the general farmers. Conclusions: The ubiquitous agricultural information system was judged to be developed for the computer because spread and use of it exceeds the other devices. Also, the information system based on the smartphone could be a complementary way if the rapid of the smartphones continues and proper education on use of the phone is provided.

• Animal cells and systems
• /
• v.16 no.4
• /
• pp.295-301
• /
• 2012

Interdigital tissue regression is one of the most well-known examples of embryonic programmed cell death, providing the mechanism behind separation of developing digits. Caspases have been shown to play a key part in this process, with activated caspase-3 localized between the developing digits. In caspase-3 knock-out adult mice, however, the digits are completely separated with no webbing. In other mutants with defects in the apoptotic machinery, such as Apaf1 deficient mice, interdigital tissue regression is initially inhibited but the webbing eventually disappears as alternative/additional cell death mechanisms step in. In order to investigate whether a similar temporal effect occurs after loss of caspase-3, we have used an in vitro approach to inhibit caspase-3 at specific times during digit separation. Previous limb explant culture approaches have encountered problems with proper limb development in culture, and thus a modified technique was used. The new approach enables detailed observation of the effects of caspase-3 inhibition on interdigital regression. Using these methods, we show that caspase-3 inhibition caused a delay in the loss of interdigital tissue compared with control explants, similar to that observed in Apaf1 mutant mice. Along with immunohistochemistry, active caspase-3 positive cells of the interdigital vs. digital regions were measured by flow cytometry. Notably, activated caspase-3 in vivo was found not only in the interdigital mesenchyme but also in the TUNEL negative digit region, supporting a role for caspase-3 in nonapoptotic events.

• Journal of Ocean Engineering and Technology
• /
• v.26 no.5
• /
• pp.63-72
• /
• 2012

The product lifecycle of a marine vessel can be classified into the design-production, operation-maintenance, and disposal phases. During the operation and maintenance phase, status data should be gathered from the major machinery and instruments installed on the marine vessel in order to perform efficient maintenance work. Although a PLM (product lifecycle management) system can manage the product information during the design and assembly stage, a PLM based on asset management technology is more appropriate for product information management during the operation stage. Product embedded information devices (PEIDs) are suggested for gathering real-time maintenance information during the operation and maintenance lifecycle. A PEID allows PLM to provide the capability of offering active information exchange between the lifecycle management system and equipment. This study designed a PEID to effectively obtain information and interact with a PLM system. It consists of sensors, wireless communication, and a micro-processor, which allow it to accumulate status data on the PLM system. The embedded information device and PLM enable the seamless information flow, tracking, and updating of MRO (maintenance repair and overhaul) information for a product throughout the middle of the product lifecycle.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.28 no.6
• /
• pp.1563-1583
• /
• 2018

With the deregulation of electronic finance, FinTech has been revitalized. The discussion on artificial intelligence is active in the financial industry. However, there is a problem of increasing security threats behind new technologies. Security vulnerabilities have increased because we are more connected than before, and the channels and entities of the financial industry have diversified. Although there are technical and policy discussions on security, the essence of all discussions is human. Fundamentals of finance are trust and security, and attention to human factors is important. This study presents the role of human and artificial intelligence for financial security, respectively. Furthermore, this derives a collaborative model in which human and artificial intelligence complement each other's limitations. To support this, it first discusses the development of finance and IT, AI, human factors, and financial security threats. This study suggests that the security threats will intensify in the era of new technology, but it can overcome them by using machinery and technology.

• Journal of Korea Technology Innovation Society
• /
• v.19 no.3
• /
• pp.545-571
• /
• 2016

The development of ICT brings a big change in manufacturing industries, and new information technology such as IoT, AR, and big data was applied on manufacturing process. As a result, the concept of smart factory has been introduced as a new manufacturing paradigm. In fact advanced countries like USA, Germany, and Japan have actively introduced smart factory in their manufacturing industries such as electronic, automobile, machinery, to improve production efficiency and quality. The manufacturing environment has been changed into flexible system, so that smart factory will be leading future manufacturing industries. Thes changes have more severe influence on Korean manufacturing industries. Mny industrial companies, have a strong interest in smart factory and they, particularly big enterprises, have been adopting smart factory to increase their manufacturing efficiencies. However, Korean small and medium-sized enterprises (SMEs) have many financial and technological difficulties so that the diffusion of smart factory in Korean SMEs has not been satisfiable up to present. However, smart factory is very important for enhancing their competitiveness in global market. Therefore, this study aims at identifying the standardization strategy of smart factory in so-called Korean 'roots industry' by presuming that the standardization will activate the diffusion of smart factory among Korean SMEs. For this purpose, first, this study examines the competitiveness of SMEs, especially in 'roots industry' and identifies the necessity of diffusion of smart factory among those SMEs. Second, based on the active review on the existing literature, this study identifies four factor groups that would influence the adoption or diffusion of standardized smart factory. They are technological, organizational, industrial and policy factors. Third, using those four factors, this study made two comprehensive case analyses on the adoption and diffusion of smart factory. These two companies belong to molding sector which is one of the important six sectors in 'root industry'. Finally, based on the theoretical and empirical analyse, this study suggests four strategies for activating the standardization of smart factory; international standardization, government-leading standardization, firm-leading standardization, and non-standardization.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.3
• /
• pp.213-218
• /
• 2007

In order to find out proper PVdF gel polymer electrolyte for Li/S battery, we investigated PVdF gel polymer electrolytes with various glyme type plasticizer such as polyglyme, tetraglyme, triglyme. The organic solvents as triglyme, tetraglyme, polyglyme (Mn = 250, 500) has different chain length of ethylene oxide(EO) in solvent of glyme system. ionic conductivity decreased as increasing chain length of EO in plasticizers. Ionic conductivity of PVdF gel electrolyte with tetraglyme, triglyme, polyglyme (Mn = 250, 500) at room temperature was $5{\times}10^{-4},\;3{\times}10^{-4},\;6{\times}10^{-5},\;3{\times}10^{-5}\;S/cm$, respectively. Li/S cell with PVdF gel polymer electrolyte using tetraglyme plasticizer had low interfacial resistance and the highest initial discharge capacity of 1232 mAh/g of active sulfur, which was about 70% utilization of theoretical value.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.3
• /
• pp.230-237
• /
• 2017

In this study, electrochemical methods were used to determine the optimum protection potential of S355ML steel for the cathodic protection of offshore wind-turbine-tower substructures. The results of potentiodynamic polarization experiments indicated that the anodic polarization curve did not represent a passivation behavior, while under the cathodic polarization concentration, polarization was observed due to the reduction of dissolved oxygen, followed by activation polarization by hydrogen evolution as the potential shifted towards the active direction. The concentration polarization region was found to be located between approximately -0.72 V and -1.0 V, and this potential range is considered to be the potential range for cathodic protection using the impressed current cathodic protection method. The results of the potentiostatic experiments at various potentials revealed that varying current density tended to become stable with time. Surface characterization after the potentiostatic experiment for 1200 s, by using a scanning electron microscope and a 3D analysis microscope confirmed that corrosion damage occurred as a result of anodic dissolution under an anodic polarization potential range of 0 to -0.50 V, which corresponds to anodic polarization. Under potentials corresponding to cathodic polarization, however, a relatively intact surface was observed with the formation of calcareous deposits. As a result, the potential range between -0.8 V and -1.0 V, which corresponds to the concentration polarization region, was determined to be the optimum potential region for impressed current cathodic protection of S355ML steel.

• International Commerce and Information Review
• /
• v.17 no.1
• /
• pp.165-191
• /
• 2015

The results of this study are the two. First, for convergence technology and convergence technology transfer based on analysis of previous studies I suggested a framework for convergence-type technology transfer conceptualization and measurement. Second, I am compared convergence-type technology transfer to total technology transfer from public research(university and public institute) to SME. Overall, despite the trend to increase technology transfer to SMEs, convergence-type technology transfer is only 4.4%. Both total technology transfer and convergence-type technology transfer to the Industry is active to electronic components, machinery, chemicals, food and beverage, and the medical. The role of universities is emphasized in both total technology transfer and convergence-type technology transfer. There are small transactions of less than 5 million in both total technology transfer and convergence-type technology transfer. Both total technology transfer and convergence-type technology transfer to the region are concentrated in Seoul, Daejeon and Gyeonggi-do.

• Journal of agriculture & life science
• /
• v.46 no.2
• /
• pp.179-190
• /
• 2012

This study was performed to obtain a heat saving effect and enhance the efficiency of a greenhouse by using a hot water piping in order to minimize the operating costs of a greenhouse as oil prices continue to rise. This method also reduces the likelihood of accidents caused by snowdrifts in regions with heavy snowfall. In general, the experimental plot was $2.0{\sim}6.0^{\circ}C$ higher than the control plot. When the skylight felt was opened, the minimum temperature was in the range of $3.0{\sim}12.0^{\circ}C$. Therefore, we judged that damage caused by snowdrifts may be prevented partly by active heating. The temperature difference inside of the greenhouse by height was insignificant. The maximum heating load of the greenhouse according to crop was respectively about $37,000kcal{\cdot}h^{-1}$ and $41,700kcal{\cdot}h^{-1}$. During the experiment, the heat value of each designed temperature in the range of the minimum ambient temperature $-11.9{\sim}4.0^{\circ}C$ was about 95,000~322,000 kcal and it was in the range of $6,050{\sim}20,900kcal{\cdot}h^{-1}$. If it is compared with the maximum heating load, it can be shown that about 15~56% of the heating energy can be supplied. The total heat value and the amount of power consumption were 2,629,025 kcal and 677.3 kWh respectively during the experiment. If it is heated with diesel, a fossil fuel, the consumption during the experiment was 291 L and the cost was 331,700won. Total cost of using electric power was about 24,400 won and it is shown that it is about 7.5% of the cost of diesel consumption. Also, if the total amount of power consumption is converted into energy, it is approximately 582,200 kcal and the energy was just about 22% of the total heat value.

• (The) Research of the performance art and culture
• /
• no.22
• /
• pp.371-411
• /
• 2011

In the twenty first century of rapid cultural change performing art requires new mode of expression based on imaginative power and creativity as well as establishing its own identity. The modern technological environment support this with advanced technology and bring about the expansion of reason from new experience. The introduction of digital media on artistic expression in particular, expands the physical ability of human body which is the main subject of performing art. A virtual body from digital technology is freed from physical boundaries and goes over space and time. It also suggests the possibility of new mode of communication with audience. This study aims at examining the subject of performing art and its digitalized movement focusing on EveR, the world's first professional robot actor. The robot actor which came on stage according to the new expression medium, a digital body, stands in need not only of technological value but also of cultural and artistic application for expression in art. In this endeavor to meet the demand, this study examines the development process and function of 'EveR' the robot actor. Also it searches into the performance of Ever which replaced human being as well as the historical significance of the title:the world's first. To be more specific, there is a example research on two performances:a pansori play "EveR is simply stunning(2009)" and children's play "The Robot Princess and Seven Dwarfs(2009)." Through this example research, it is enabled to anticipate the influence of robot actors on performing arts and to search for the better way of them to evolve. Furthermore, it aims at finding ways to create high value through promoting robot actors to be familiar to the public as well as supporting them to become active cultural contents. The performance with robotic technology is one of the artistic experiment that may cause the change of the future of performing art by actualizing technological imagination together with human body and machinery. As a consequence, it is expected that the meeting of performing art and robotic technology gives positive influence on activating performing art as one of the integrated cultural phenomenon which satisfies the taste of modern era. Moreover, this study may also be the beginning of the expansion of performing art to stretch to diverse field.