• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제36회 춘계학술대회논문집
• /
• pp.253-257
• /
• 2011

고체로켓에서 발생하는 vortex shedding 현상 중 인히비터로 인해 발생하는 연소실내 와류(vortex)의 특성을 조사하기 위해 Large Eddy Simulation을 수행하였다. 해석의 결과는 기존 연구자들의 결과와 잘 일치하며 정략적 및 정성적 분석을 수행하였다. 인히비터 후방에서 발생하는 vortex는 Flow-acoustic coupling 에 의해 주기적으로 반복되며 생성, 소멸이 이루어지는 것을 확인 할 수 있었으며, 발생 주기는 연소실내 mode 2의 주파수와 일치하는 것을 확인하였다. 3차원 해석결과 인히비터 후방에서 Roll 발생은 비균일한 노즐 유동을 발생시킨다.

• 한국정보기술응용학회:학술대회논문집
• /
• 한국정보기술응용학회 2005년도 6th 2005 International Conference on Computers, Communications and System
• /
• pp.215-218
• /
• 2005

We have investigated on the development of 2-2 piezocomposites that have better piezoelectric activity and lower acoustic impedance than those of conventional piezoceramics. In this study, we have investigated the piezoelectric and acoustic properties of 2-2 piezocomposites sensor which were fabricated using dice-and-fill technique for the different volume fraction of PZT. The resonance characteristics measured by an impedance analyzer were similar to the analysis of finite element method. The resonance characteristics and the electromechanical coupling factor were the best when the volume fraction PZT was 0.6. It also showed the highest result from the standpoint of sensitivity, bandwidth and ring-down property and so on at the same condition. The specific characteristics shows that the 2-2 piezocomposites turned out to be superior to the ultrasonic sensor composed by single phase PZT.

• 소음진동
• /
• 제9권4호
• /
• pp.822-827
• /
• 1999

The reduction of booming noise level and improvement of sound quality in the vehicle interior have been major fields of vehicle NVH for many years. In order to reduce the booming noise this paper proposed a system variable, which takes account of mode shapes and natural frequencies of the structural-acoustic system, measurement points and excitation frequency. By simplifying the system variable, the major contributors of panels inculding roof, roof lining, wind shield glasses, doors and floor to booming noise at a specific frequency was experimentally found. Also the relationships between structural modes of roof lining, one of the major contributors, and acoustic modes of compartment cavity were investigated from the viewpoint fo structure-borne noise. In addition, the roof lining was modified structurally by applying marble sponge to the gap between roof and roof lining. Asthe result of structural modification, the booming noise was reduce at target frequency.

• 한국연소학회지
• /
• 제23권1호
• /
• pp.28-35
• /
• 2018

Entropy waves(or hot spots) in a gas turbine combustor are generated by irregular heat release from flames, then can be coupled with acoustic waves when they are accelerated at the exit of the combustor. This coupling mechanism between the entropy and the acoustic waves is generally known to be one of the triggers for combustion instability, which is commonly called "indirect" combustion noise. This paper reviews the fundamental theories on generation, propagation, and coupling with acoustic field of entropy waves and recent research results on the indirect combustion noise for gas turbine combustors.

• 한국환경과학회지
• /
• 제18권11호
• /
• pp.1291-1297
• /
• 2009

The purpose of this study was to establish structural bone noise analysing method for apartments building floor with Structural-Acoustic coupling analysis. Nowadays, noise through floor is recognized as important problem with the consequence that noise isolation technique is studied in the various fields of industry. From among noise factors, resonance sound is main reason for floor's solid noise. therefore, In this study, evaluation method for composite material slab is established and that a case study is suggested with it.

• 한국소음진동공학회논문집
• /
• 제15권10호
• /
• pp.1211-1216
• /
• 2005

Underwater acoustic transducers are widely used for SONAR application, whose important design parameters are shapes. materials, dimensions and supporting structures. Practical design method of transducers consists of manufacturing, experiments and modifications so that it requires much time and expenses. In this study, an analytical method was developed for the Tonpilz type transducers using the commercial finite element analysis code ATILA which can solve the electro-mechanical coupling problems. A finite element model was established including the transducer elements such as ceramic stack, head mass, tail mass, tensile bolt, and molding layers. The proposed model was verified and modified by comparing the in-air and in-water test results of prototypes. The developed analysis method will be effectively used for the sensitivity analysis of design parameters in transducer design process.

• 한국세라믹학회지
• /
• 제40권4호
• /
• pp.393-397
• /
• 2003

To investigate the effect of AIN c-axis orientation on the resonance performance of film bulk acoustic wave resonators, solidly mounted resonators with crybtallographically different AIN piezoelectric films were prepared by changing only the bottom electrode surface conditions. As increasing the degree of c-axis texturing, the effective electromechanical coupling coefficient ($\kappa$$\_$eff/)$^2$ in resonators increased gradually. The least 4 degree of full width at half maximum in an AIN(002) rocking curve, which corresponds to $\kappa$$^2$$\_$eff/ of above 5%, was measured to be necessary for band pass filter applications in wireless communication system. The longitudinal acoustic wave velocity of AIN films varied with the degree of c-axis texturing. The velocity of highly c-axis textured AIN film was extracted to be about 10200 n/s by mathematical analysis using Matlab.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.447-449
• /
• 2004

The purpose of this study is measured surface acoustic wave(SAW) characteristics to confirm utilization possibility as SAW sensor using new Pb(Mg$_{1}$3/Nb$_{2}$3/) $O_3$-PbTiO$_3$ (PMN-PT) piezoelectric substrate. We have tried to see if the material can be practically available as a new surface acoustic wave (SAW) biosensor to detect protein. The experimental results clarified that the frequency filtering of the central frequency of the PMN-PT substrate is a superior result to that of the LiTaO$_3$ (LT) substrate, but the result was not completely satisfactory. We know there is a problem in the design of inter-digital transducer (IDT) pattern. The waves transferred through the input terminal forms SAW which is sure to be transferred to the direction of the output terminal and the backward direction of the input terminal. This reflected wave is reiterated with SAW, which is transferred to the output direction, and so the frequency filtering gives a not good result. The electromechanical coupling coefficient of the PMN-PT substrate is excellent, and we can use it as a SAW sensor, in the near future, provided that there will be a new IDT design to increase the frequency filtering.

• 한국소음진동공학회논문집
• /
• 제14권8호
• /
• pp.718-725
• /
• 2004

If a wall separates the bounded and unbounded spaces, then the wall’s role in transporting the acoustic characteristics of the two spaces is not well defined. In this paper, we attempted to see how the acoustic characteristics of two spaces are really affected by the spatial characteristics of the wall. In order to understand coupling mechanism, we choose a finite space and a semi-infinite space separated by the flexible or rigid wall and an opening. A volume interaction can be occurred in structure boundary and a pressure Interaction can be happened in the opening boundary. For its simplicity, without loosing generality, we use rather simplified rectangle model instead of generally shaped model. The source impedance is presented to the various types of boundaries. The distributions of pressure and active intensity are also presented at the cavity- and structure-dominated modes. The resulting modification, shifts of modal frequencies and changing of standing wave patterns to satisfy both coupled boundary conditions and governing equations, are presented.

• The Journal of the Acoustical Society of Korea
• /
• 제19권1E호
• /
• pp.27-37
• /
• 2000

This paper presents a simplified analytical formulation for computing acoustic power radiation from a rectangular plate exposed to random forces such as turbulent boundary layer pressure fluctuations and arbitrary mechanical force in a subsonic flow field. The expression for the acoustic power is derived using modal expansion method and light fluid loading is assumed on the plate. In order to simplify the formulation for acoustic power due to combined excitations of mechanical forces and turbulent pressures, it is assumed that the structural damping of the plate is small and excitations are broadband random forces having frequency spectra above the convective coincidence. Under these assumptions, an approximate solution for the broadband acoustic power radiation from a plate excited by both turbulent pressures and arbitrary mechanical forces is obtained and evaluated considering the effect of modal coupling on the radiated acoustic power. An efficient method is also suggested to compute modal acoustic impedance in a moving fluid medium by using averaged Green function.