• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.3
• /
• pp.373-381
• /
• 2000

The flow and heat transfer characteristics on the impingement surface can be controlled by the change of vortex with the acoustic excitation, because the flow characteristics of an impinging jet are affected strongly by the vortices formed at the jet exit. To investigate the effects of acoustic excitation, we measured the velocity, turbulent intensity distributions for the free jet and local heat transfer coefficients on a impingement surface. As the acoustic excitation, subharmonic frequency of excited frequency plays an important role to the control of the jet flow. If the vortex pairings are promoted by the acoustic excitation, turbulence intensity of the jet flow is increased quickly. On the other hand if the vortex pairings are suppressed, the jet flow has low turbulence intensity at the center of the jet. Therefore, the low heat transfer rates are obtained on the impingement plate for a small nozzle-to-plate distance. However, it has high heat transfer rates at a large distance between the nozzle and plate due to the increasing of potential-core length.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.10 s.115
• /
• pp.1057-1066
• /
• 2006

Acoustic streaming Induced by longitudinal vibration at 30 kHz is visualized for a test fluid flow between the stationary glass plate and ultrasonic vibrating surface with particle imaging velocimetry (PIV) To measure an increase in the velocity of air flow due to acoustic streaming, the velocity of air flow in a gap between the heat source and ultrasonic vibrator is obtained quantitatively using PIV. The ultrasonic wave propagating into air in the gap generates steady-state secondary vortex called acoustic streaming which enhances convective cooling of the stationary heat source. Heat transfer through air in the gap is represented by experimental convective heat transfer coefficient with respect to the gap. Theoretical analysis shows that gaps for maximum heat transfer enhancement are the multiple of half wavelength. Optimal gaps for the actual design are experimentally found to be half wavelength and one wavelength. A drastic temperature variation exists for the local axial direction of the vibrator according to the measurement of the temperature distribution in the gap. The acoustic streaming velocity of the test fluid in the gap is at maximum when the gap agrees with the multiples of half wavelength of the ultrasonic wave, which are specifically 6 mm and 12 mm.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.6
• /
• pp.103-109
• /
• 2017

An increase in acoustic energy in a combustion chamber coupled with heat fluctuations from flame results in the occurrence of combustion instability. The assessment of combustion stability requires the prediction of acoustic energy variation by understanding the acoustical characteristics of flow boundaries in a combustion chamber. The present paper discusses about the characteristics of acoustic impedances at boundaries in terms of Strouhal number and summarizes theoretical analyses on the acoustic characteristics of injector-head-like configurations. Also, the details of the two-microphone measurement technique have been presented.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.254-257
• /
• 2010

Acoustic design parameters of a Helmholtz resonator are studied experimentally and numerically for acoustic stability in a model acoustic tube. Acoustic damping is quantified by the amplitude of the fluid velocity in mass-spring-damper system. The length of an orifice, the volume of a cavity, and the diameters of an orifice and a cavity in the resonator are selected as design parameters for tuning of the resonator. It is found that acoustic damping capacity is increased by shorter orifice and longer cavity in the resonator. As the ratio of the orifice diameter to the cavity diameter increases in the resonator, the damping capacity decreases.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.2
• /
• pp.119-127
• /
• 2014

An epoxy coating applied to the concrete surface of a containment building deteriorates in hazardous environments such as those containing radiation, heat, and moisture. Unlike metals, the epoxy coating on a concrete liner absorbs and discharges moisture during the degradations process, so it has a different density and volume during service. In this study, acoustic impedance was adopted for characterizing the degradation of a glass-reinforced epoxy coating using the acoustic reflection coefficient (reflectance) on a rough epoxy coating. For estimating the acoustic reflectance on a wavy epoxy coating surface, a probabilistic model was developed to represent the multiple irregular reflections of the acoustic wave from the wavy surface on the basis of the simulated annealing technique. A number of epoxy-coated concrete specimens were prepared and exposed to accelerated aging conditions to induce an artificial aging degradation in them. The acoustic impedance of the degraded epoxy coating was estimated successfully by minimizing the error between a waveform calculated from the mathematical model and a waveform measured from the surface of the rough coating.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.625-628
• /
• 2005

Silencers are extensively used for reducing noise in an exhaust system of internal combustion Engine and fluid machineries. The prediction and measurement of the transmission loss as the acoustic performance of silencers are important in early design stage. In the measurement of transmission loss, the semi-anechoic terminations are general used for reducing unwanted effects by reflecting wave. However it is very hard to remove reflecting wave perfectly. So the research about the error made by reflecting wave is important. The analysis about errors made by reflections and modification techniques are proposed. For an application example, the diesel particulate filter (DPF) is chosen. The transmission loss of DPF is measured with and without considerations of reflecting wave.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.242-242
• /
• 2013

Recently, importance of working environment is increased in commercial vessel and offshore structure. Marine facility design and ambient environment condition are influenced to enhancing human performance and reducing human errors. Consequently, the quality of accommodation where offshore facility crews sleep, eat and relax will influence their job performance and overall sense of comport and well-being. Therefore, adequate acoustic isolation between adjacent spaces is normally required to achieve satisfactory internal noise levels, acoustic privacy and speech intelligibility. In this study, the reverberation time is investigated in the public areas where there are not provided the information of material's noise reduction coefficient (NRC). The experiment of reverberation time is rarely performed for the various type public areas in a marine structure. Therefore, the reverberation time in a vessel is investigate in order to evaluate the room's noise reduction coefficient (NRC) in a public area.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.12 no.2
• /
• pp.87-96
• /
• 2004

Acoustic performances of the steel-wire fabrics manufactured from the crushed tires were experimentally investigated for various thicknesses and bulk densities. The well- known two-cavity method was used to measure the characteristic impedances, the propagation constants, and the absorption coefficients. The normal absorption coefficients measured by the two-cavity method agreed well with those measured by the two-microphone impedance tube method. The experimental results showed that the magnitude and frequency range of the absorption coefficient were controllable by changing the thickness and the bulk density of the steel-wire fabrics. Therefore, the steel-wire fabrics from the crushed tires can be successfully used as a good sound absorbing material.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.29-32
• /
• 2008

In this study, acoustic diffusers were designed as to the ISO method, which measured the random-incidence scattering coefficient of surfaces in a diffuse field. The diffusers which were made of GFRG (Glass Fiber Reinforced Gypsum), consisted of the cubes with different height and width. The height was from 50 to 250 mm and the maximum height was at the center of the diffusers to provide the early reflections. The surfaces were irregularly designed in order to add the lateral reflections. The scattering coefficient of the diffusers was measured in a 1;10 reverberation chamber, but the absorption coefficient was measured in a real scale reverberation chamber. The result of the scattering coefficient was compared to the hemisphere diffusers and the absorption coefficient was compared to ISO 354 data. To validate the measurement results, the scattering coefficient of the diffusers will be measured in a real scale reverberation chamber.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.361-364
• /
• 1995

Wavelet Transform is a new tools for signal processing, such as data compressing extraction of parameter for Reconition and Diagnostics. This transform has an advandage of a good resolution compared to Fast Fourier Transform (FFT) In this study, we employ the wavelet transform for analysis of Acoustic Emission raw signal generated form rotary compressor. In abnormal condition of rotary compressor, the state of operating condition can be classified by analizing coefficient of wavelet transformed signal.