• Polymer(Korea)
• /
• v.34 no.2
• /
• pp.104-107
• /
• 2010

Polyurethane (PU) sheets were fabricated by the reaction of polypropylene glycol (PPG) and liquid diphenyl methane diisocyanate (L-MDI) with various trimethylol propane (TMP) contents. The $T_g$ value was varied from 34.8 $^{\circ}C$ to 49.9 $^{\circ}C$ according to the TMP content. As the content of TMP was increased from 4 to 12 wt%, the modulus of the PU sheet was increased from 322 MPa to 423 MPa, its tensile strength was increased from 10.6 MPa to 14.8 MPa, and its elongation was decreased from 62.8% to 49%. In case of acoustic properties, the sound speed of PU sheet was increased while its attenuation coefficient was decreased as the content of TMP was increased. The fabricated PU sheet was stable in water bath for 4 weeks.

• Journal of Biosystems Engineering
• /
• v.33 no.5
• /
• pp.348-354
• /
• 2008

Egg grading is determined by exterior and interior quality. Among the evaluation methods for the egg quality, a candling method is common to identify eggs with cracked shells and interior defects. But this method is time-consuming and laborious. In addition, practically, it is challenging to detect hairline and micro cracks. In this study, an on-line inspection system based on acoustic resonance frequency analysis was developed to detect hairline cracks on eggshells. A roller conveyor was used to transfer eggs along one lane to the impact position where each of eggs rotated by the roller was excited with an impact device at four different locations on the eggshell equator. The impact device was consisted of a plastic hammer and a rotary solenoid. The acoustic response of the egg to the impact was measured with a small condenser microphone at the same position as the impact device was installed. Two acoustic parameters, correlation coefficient for normalized power spectra and standard deviation of peak resonant frequencies, were used to detect cracked eggs. Intact eggs showed relatively high correlations among the four normalized power spectra and low standard deviations of the four peak resonant frequencies. On the other hand, cracked eggs showed low correlations and high standard deviations as compared to the intact. This method allowed a crack detection rate of 97.6%.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.4
• /
• pp.15-23
• /
• 2015

This study predicts the basic characteristics of combustion instabilities in a gas turbine lean premixed combustor using ASCI3D code which is a FEM(Finite Element Method)-based Helmholtz solver. The prediction results show the good agreement with the measured data in modeling the overall combustion instability features, however, the code is found to overpredict the unstable conditions. As one of the efforts to improve the model accuracy, the effects of acoustic boundary conditions on the instability growth rate are analyzed. As a result, it is shown that the acoustic reflection coefficient has a great impact on the instability and the prediction accuracy can be enhanced by defining the precise acoustic conditions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.9
• /
• pp.1253-1262
• /
• 2001

Experimental study is conducted to investigate the heat/mass transfer and flow characteristics for the flow over backward-facing step and cavities. A naphthalene sublimation method has been employed to measure the mass transfer coefficients on the duct wall and LDV system has been used to obtain mean velocity profiles and turbulence intensities. Reynolds number based on the step height and free stream velocity is 20,000 and St numbers of acoustic excitations given to separated flow are 0.2 to 0.4. The spectra of streamwise velocity fluctuation show a sharp peak forcing frequency for an acoustically excited flow. The results reveal that the vortex pairing and overall turbulence level are enhanced by the acoustic excitation and a significant decrease in the reattachment length and the increased turbulence intensity are observed with the excitation. A certain acoustic excitation increases considerably the heat/mass transfer coefficient at the reattachment point and in the recirculation region. For the cavities, heat/mass transfer is enhanced by the acoustic excitation due to the elevated turbulence intensity. For the 10H cavity, the flow pattern is significantly changed with the acoustic excitation. However, for the 5H cavity, the acoustic excitation has little effect on the flow pattern in the cavity.

• International Journal of Automotive Technology
• /
• v.5 no.4
• /
• pp.303-309
• /
• 2004

In this paper, an interfacial crack length has been detected by using the ultrasonic attenuation coefficient on the adhesively bonded double-cantilever beam (DCB) joints. The correlations between energy release rates which were investigated by experimental measurement, the boundary element method (BEM) and Ripling's equation are compared with each other. The experimental results show that the interfacial crack length for the ultrasonic attenuation coefficient and energy release rate increases proportionally. From the experimental results, we propose a method to detect the interfacial crack length by using the ultrasonic attenuation coefficient and discuss it.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1109-1114
• /
• 2003

The initial crack often occurs on the bonded interface and it is the general cause of the interface fracture. It is very significant to establish the measurement method of interfacial crack by applying the ultrasonic technology into the interface of bonded dissimilar materials. In this paper, the interfacial crack length was measured by ultrasonic attenuation coefficient in the Al/Epoxy bonded dissimilar materials of double-cantilever beam(DCB). The energy release rate, G, was obtained by the experimental and Ripling's equation measurement of compliance. The experimental results represent that the relation between interfacial crack length for the ultrasonic attenuation coefficient and energy release rate is increased proportionally. From the experimental results, a measurement method of the interfacial crack length by the ultrasonic attenuation coefficient was proposed and discussed.

• Journal of Korea Society of Industrial Information Systems
• /
• v.6 no.3
• /
• pp.107-114
• /
• 2001

This paper describes Connected Digit Recognition with Considering Acoustic Feature in Korea. The recognition rate of connected digit is usually lower than word recognition. Therefore, speech feature parameter and acoustic feature are employed to make robust model for digit, and we could confirm the effect of Considering. Acoustic Feature throughout the experience of recognition. We used KLE 4 connected digit as database and 19 continuous distributed HMM as PLUs(Phoneme Like Units) using phonetical rules. For recognition experience, we have tested two cases. The first case, we used usual method like using Mel-Cepstrum and Regressive Coefficient for constructing phoneme model. The second case, we used expanded feature parameter and acoustic feature for constructing phoneme model. In both case, we employed OPDP(One Pass Dynamic Programming) and FSA(Finite State Automata) for recognition tests. When appling FSN for recognition, we applied various acoustic features. As the result, we could get 55.4% recognition rate for Mel-Cepstrum, and 67.4% for Mel-Cepstrum and Regressive Coefficient. Also, we could get 74.3% recognition rate for expanded feature parameter, and 75.4% for applying acoustic feature. Since, the case of applying acoustic feature got better result than former method, we could make certain that suggested method is effective for connected digit recognition in korean.

• Journal of the Korean Ceramic Society
• /
• v.38 no.11
• /
• pp.980-986
• /
• 2001

Bragg reflector type FBAR was fabricated on the Si(100) substrate. We measured a frequency response of the resonator at 5.2 GHz and analyzed it by numerical calculation considering actual acoustic losses of each layer in the structure. We fabricated nine layer Bragg reflector of W-SiO$_2$pairs using r.f. sputtering method and fabricated AlN piezoelectric and Al electrodes using pulsed dc sputtering. The return loss(S$_{11}$) of the fabricated Bragg reflector type FBAR was 12 dB at 5.38 GHz and the series resonance frequency(f$_{s}$) was 5.376 GHz and the parallel resonance frequency(f$_{p}$) was 5.3865 GHz. Effective electro-mechanical coupling constant (K$_{eff{^2}}$) and Quality factors(Q$_{s}$), the Figures of Merit of the resonator, were about 0.48% and 411, respectively. We extracted acoustic parameters of AlN piezoelectric and reflection coefficient of the Bragg reflector by numerical calculation. We could know that material acoustic impedance and wave velocity of AlN piezoelectric decreased for intrinsic value and the electromechanical coupling constant(K$_2$) value was very low owing to the poor quality of the AlN piezoelectric. Reflection coefficient of Bragg reflector was 0.99966 and reflection band was very wide from 2.5 to 9.5 GHz.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.3E
• /
• pp.10-17
• /
• 2001

The possibility is investigated of determining the diffuse absorption coefficients of the wall surfaces in a real room by minimizing the errors between the measured energy impulse response of a real room and the predicted energy impulse responses obtained from the ray tracing simulation of the room. In other words, this can possibly serve as a basis for "acoustical system identification" in attempting to determine the "best fit" of modelled absorption coefficients to measured energy response data. Algorithms for attempting this were investigated. The algorithms developed for this purpose proved to be rigorous and efficient. Instead of using the ray tracing model to determine the absorption coefficients, the phase image model was used in order to determine the acoustic impedances of wall surfaces. However, the numerical algorithms could not find the correct impedance values, primarily due to the wide range of the acoustic impedance values of any single acoustic material and very long computation time.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.1
• /
• pp.42-46
• /
• 2002

In this paper, a new pre-processing algorithm is proposed to improve the performance of stereo acoustic echo canceller. The proposed algorithm has the improved performance by the estimation error reduction of filter coefficient using input signal which was reduced reverberation of room in the basis MINT (Mu1tip1e-input/output Inverse Theorem) filtering. For real stereo speech signal and real room impulse response the results of simulation, we showed that the proposed method could improved 3∼5 dB ERLE (Echo Return Loss Enhancement) regardless of NLMS (Normalized Least Mean Square) and Projection adaptive algorithm.