• 산업경영시스템학회지
• /
• 제46권3호
• /
• pp.1-6
• /
• 2023

In the realm of dental prosthesis fabrication, obtaining accurate impressions has historically been a challenging and inefficient process, often hindered by hygiene concerns and patient discomfort. Addressing these limitations, Company D recently introduced a cutting-edge solution by harnessing the potential of intraoral scan images to create 3D dental models. However, the complexity of these scan images, encompassing not only teeth and gums but also the palate, tongue, and other structures, posed a new set of challenges. In response, we propose a sophisticated real-time image segmentation algorithm that selectively extracts pertinent data, specifically focusing on teeth and gums, from oral scan images obtained through Company D's oral scanner for 3D model generation. A key challenge we tackled was the detection of the intricate molar regions, common in dental imaging, which we effectively addressed through intelligent data augmentation for enhanced training. By placing significant emphasis on both accuracy and speed, critical factors for real-time intraoral scanning, our proposed algorithm demonstrated exceptional performance, boasting an impressive accuracy rate of 0.91 and an unrivaled FPS of 92.4. Compared to existing algorithms, our solution exhibited superior outcomes when integrated into Company D's oral scanner. This algorithm is scheduled for deployment and commercialization within Company D's intraoral scanner.

• 대한치과기공학회지
• /
• 제41권1호
• /
• pp.21-27
• /
• 2019

Purpose: To evaluate 2D and 3D of occulsal, mesial-occlusal and mesial-occlusal-distal cavity of composite resin inlay. Methods: Abutment tooth 16, 36 of FDI system was selected for the study. Inlay prostheses classified as occlusal cavity (OC group), mesial-occlusal (MOC) and mesial-occlusal-distal cavity (MODC) were prepared using composite resin. Composite resin was injected with composite resin in prepared tooth cavity and then photopolymerized with UV light. Additional thermal polymerization was performed. Marginal gap of composite resin inlays were measured by digital microscope(x160) with silicone replica technique. The data was analyzed from statistical software for Kruskal-Wallis test (${\alpha}=0.05$). 3-dimensional analysis was analyzed through superimposition method. Results: The smallest 2D marginal fit measure of the three groups was $47.0{\pm}21.6{\mu}m$ in the MOC group. The largest 2D marginal was $69.1{\pm}33.8{\mu}m$ in the MODC group. In the trueness of the three groups, the most accurate figure was $14.4{\pm}2.3{\mu}m$ for the MODC group. In Precision, the most accurate figure was $14.5{\pm}4.3{\mu}m$ for the MODC group. Conclusion : In this study, 2D marginal fit of OC, MOC, and MODC cavities fabricated with composite resin was applicable to all clinical applications. In the 3D inner surface accuracy evaluation, the MODC group showed the accuracy results.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제36권5호
• /
• pp.402-407
• /
• 2010

Introduction: The planning of implant surgery is an important factor for the implant prosthesis. Stereolithographic (SLA) surgical stents based on a computer simulation are quite helpful for clinicians to perform the surgery as planned. Although many clinical and technical trials have been performed for computed tomography (CT)-guided implant stents to improve the surgical procedures and prosthetic treatment, there are still many problems to solve. We developed a system of a surgical guide based on 3 dimensional (3D) CT for implant therapy and achieved satisfactory results in the terms of planning and operation. Materials and Methods: Fifteen patients were selected and 30 implant fixtures were installed. The preoperative CT data for surgical planning were prepared after obtaining informed consent. Surgical planning was performed using the simulation program, Ondemend3D In2Guide. The stents were fabricated based on the simulation data containing information of the residual bone, the location of the nerve, and the expected design of the prostheses. After surgery with these customized stents, the accuracy and reproducibility of implant surgery were evaluated based on the computer simulation. The data of postoperative CT were used to confirm this system using the image fusion technique and compare the implant fixtures between the planned and implanted. Results: The mean error was 1.18 (${\pm}0.73$) mm at the occlusal center, 1.23 (${\pm}0.67$) mm at the apical center, and the axis error between the two fixtures was $3.25^{\circ}C$ (${\pm}3.00$). These stents showed superior accuracy in maxilla cases. The lateral side error at the apical center was significantly different from the error at the occlusal center but there were no significant differences between the premolars, 1st molars and 2nd molars. Conclusion: SLA surgical stents based on a computer simulation have the satisfactory accuracy and are expected to be useful for accurate planning and surgery if some errors can be improved.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제33권2호
• /
• pp.158-165
• /
• 2011

A 73-year-old Korean female patient with a fully edentulous mandible was planned to have five implant fixtures installed in the anterior mandible for the fixed prosthesis. After 3-dimensional (3D) computed tomographic scanning was transferred to OnDemand3D$^{(R)}$ (Cybermed Co., Seoul, Korea) software program for the virtual planning, five fixtures of MK III Groovy RP implants of Branemark System$^{(R)}$ (Nobel Biocare AB Co., Goteborg, Sweden) were installed in the anterior mandible between both mental foramens using In2Guide$^{(R)}$ (CyberMed Co., Seoul, Korea) mucosa-supported surgical template with Quick Guide Kit$^{(R)}$ (Osstem Implant Co., Seoul, Korea) systems. Fixture installations were completed successfully without any complications, such as mental nerve injury, bony bleedings, fenestrations and other unexpected events. Postoperative computed tomographic scans were aligned and fused to the planned implant, then angular and linear deviations were compared with the planned virtual implants. The mean angular deviation between the planned and actual implant axes was $3.42{\pm}1.336^{\circ}$. The mean distance between the planned and actual implant at the neck area was $0.544{\pm}0.290$ mm horizontally and $0.118{\pm}0.079$ mm vertically. The average distance between the planned and actual implant at the apex area was $1.166{\pm}0.566$ mm horizontally and $0.14{\pm}0.091$ mm vertically. These results could be considered more precise and accurate than previous reports, and even our recent results. The entire procedures of this case are reported and reviewed.

• 대한치과보철학회지
• /
• 제38권2호
• /
• pp.242-254
• /
• 2000

Accurate impression is very important to achieve desirable prosthesis and there are many factors in taking a good impression. For example, types of impression material, types of impression tray, impression taking methods and so on. Recently individual tooth tray technique is accepted as obtaining good impression that can be applied to multiple abutment impression, heavy salivated patient, to minimize the effect of natural teeth s undercuts and to reduce pain during cord packing procedures. The purpose of this study was to compare the accuracy according to materials and forms of the individual tooth tray which is clinically applied nowadays. Used materials in experiment were divided into 3 types (acrylic resin. $Futar^{(R)}$ occlusion. $Blu-mousse^{(R)}$) and forms were divided into 2 types (forming occlusal vent hole or not and forming marginal vent space or not). Stone master model from impression body and metal master model were measured by $X-PLAN360d^{(R)}$ to compare occlusal surface discrepancy and marginal discrepancy. The results were as follows: 1. In comparison of occlusal surface discrepancy and marginal discrepancy according to materials, groups with three materials showed no statistical difference 2. In comparison of occlusal surface discrepancy and marginal discrepancy according to occlusal vent hole, groups with occlusal vent hole showed significantly less marginal discrepancy than groups with no occlusal vent hole(p<0.05). 3. In comparison of occlusal surface discrepancy and marginal discrepancy according to 0.5mm-marginal-vent-space, groups with no 0.5mm-marginal-vent-space showed significantly less marginal discrepancy than groups with 0.5mm-marginal-vent-space (p<0.05). In summary these results suggest that individual tooth tray made of 3 types of materials with occlusal vent hole and individual tooth tray made of acrylic resin with no marginal vent space showed good accuracy of impression. In addition, individual tooth tray which is made of bite registration materials may be more useful because of advantage in facility and timesaving aspect of fabrication.

• 대한치과기공학회지
• /
• 제33권1호
• /
• pp.65-77
• /
• 2011

Purpose: The purposes of this study were to provide information about safe actions during the practice of dental technology, promote belief in safe actions among the students of dental technology, and reinforce their knowledge about how to act safety. Methods: Open questions were asked to 120 sophomores majoring dental technology to understand the target group's belief about safe actions. Following the instructions by Ajzen & Fishbein, the collected data were grouped according to similar beliefs. Those beliefs of the highest frequency were given a priority and got to represent the belief level of the target group. Even with belief changes, however, they would not be able to practice safe actions if they had no knowledge about how to do safe actions. For desirable behavioral changes among the students, the students were then asked to discuss the current state of safety accidents and issues focusing on the materials and processes used in the practice and give presentations regarding the subjects to identify risk factors. Then the identified risk factors were used to devise the program contents so that the students could practice safe actions through accurate behavioral approaches and belief changes by educating them about how to act safely by the practice processes and the involved materials and devices. Results: Not only do the students of Dept. of Dental Technicians have difficulties with the complex practice processes while practicing to make dental prosthesis, but they are exposed to the risk of accidents as they're poor at dealing with the materials and devices. Although there is a definite need for accident prevention education programs before practice, the reality is that the school doesn't the schoosuch education. Based on the judgment that an education program designed to reinforce belief for behavioral changes would generate effgrams results, an education program was developed by applying the Theory of Planned Behavior(TPB). Along with their beliefs, the current state of accidents n. Basepractice, demand for safety education, and practice level of safe actions were used to device the contents of accident prevention education and to develop an accident prevention education program for dental technology. Conclusion: The study presents an accident prevention education program developed to reinforce dental technology students' beliefs and knowledge and to help them do safe actions during practice.

• 대한치과보철학회지
• /
• 제39권5호
• /
• pp.492-501
• /
• 2001

The use of alginate impression materials today is prevalent because of its efficiency and simplicity in clinical settings. Unfortunately, the simplicity of the procedure tends to lull the dentist into a sense of well-being, and lead him into using careless or sloppy technique. Alginate impression materials are used to fabricate diagnostic and preliminary casts, and the final cast. Incorrect use of this material is known to affect the accuracy of the final prosthesis. The purpose of this study was to compare the effect of different mixing methods of alginate impression material and tray adhesive on the accuracy of the stone cast produced by each method. A total of 30 stone casts were produced by using 3 different types of mixing methods (10 stone cast for each mixing method, respectively). The first method utilized an automatic-mixing machine to mix alginate while the second method was carried out manually, strictly following manufacturer's instructions. The third method also involved manual mixing, but did not follow the manufacturer's instructions and was done in a random fashion. Also, 20 additional stone casts were produced by using alginate with or without tray adhesives were included in the study to evaluate effects of tray adhesives on the accuracy of alginate impression. 10 stone casts were produced by adding tray adhesives to the interior surface of the impression tray prior to taking the impression. The other 10 excluded this step. A total of 50 stone casts were analyzed by the three-dimensional measuring machine to measure and compare the dimensional changes of the impression material of each group. The results are as follows. 1. No significant difference was found between the automatic mixing group and the manually-mixing group(p>0.05). 2. For the group that followed manufacturer's instructions, less dimensional changes were record ed than the group that didn't in measuring distanced 4(p<0.05). 3. The group that used tray adhesives showed less dimensional changes(p<0.05). The findings revealed that mechanical methods of mixing alginate impression materials had little influence on dimensional changes. However, it is proven that following manufacturers instructions in alginate impression taking is an important step in acquiring accurate impressions and tray adhesives may play an important role in enhancing the results.

• 구강회복응용과학지
• /
• 제38권3호
• /
• pp.178-188
• /
• 2022

모든 잔존치의 발거를 계획한 환자의 경우 최종 보철 제작 전 무치악으로 지내는 기간을 최소화하기 위해 미리 임시 즉시 의치를 제작하게 된다. CAD/CAM 시스템을 이용하면 전통적 방식에서의 한계점들을 보완하여 진료실과 기공실에서의 제작 과정을 간소화 시킬 수 있다는 장점이 있다. 하지만, 환자의 악간관계에 관한 정보를 정확하게 기공실의 디지털 네트워크로 전달하는 과정에서 오차가 발생하여 교합관계가 불안정하거나 비심미적인 보철물이 제작될 빈도가 높다는 단점도 있다. 이러한 문제점을 극복하기 위해 간단하고 정확한 POP BOW 시스템의 교합평면 디지털 전이법을 이용하여, 상하악 전치부 잔존치 발거 후 심미적이고 기능적인 3D 프린팅 임시 즉시의치를 장착한 환자의 성공적인 증례를 보고하고자 한다.

• 대한치과보철학회지
• /
• 제61권2호
• /
• pp.125-134
• /
• 2023

골격성 3급 부정교합은 중심위 간섭이 없다면 매우 안정적인 교합 양식이다. 또한 특징적으로 전방 유도가 없고 전치부 반대교합이 동반될 경우 적절한 교합접촉이 없을 수도 있다. 이러한 환자에서 다양한 원인으로 다수 치아를 상실하여 광범위한 구강 회복을 필요로 하는 경우, 환자의 교합관계, 안모의 변화, 측두하악관절의 평가 등 정확한 진단과 면밀한 분석이 필수적이다. 환자의 주소에 따라 심미적 개선을 위해서는 악교정 수술이 동반되는 경우가 많으나 사정 상 불가능한 경우, 최소한의 수직고경 거상을 통해 부분적으로 심미적 개선이 달성될 수 있다. 측두하악관절 장애, 비기능적 악습관 발생, 저작근의 긴장 등 예기치 못한 문제가 발생할 수 있기에 본 환자에서는 가역적인 임시 가철성 의치를 통해 적응 가능 여부를 확인하였으며, 이후 고정성 임시 보철물을 통해 악관절 및 저작근의 적응 여부를 면밀히 관찰하였다. 이후 단계적 치료과정을 통해 상악 전악 임플란트 지지 고정성 보철물과 하악 고정성 보철물을 통해 안정적인 구치부 지지를 얻고 상악 전치부 심미의 부분적 개선을 이루었기에 본 결과를 보고하고자 한다.