• Advances in materials Research
• /
• 제3권3호
• /
• pp.163-174
• /
• 2014

In this study, fatigue properties and crack growth characteristics of a polycarbonate (PC) were examined during cyclic loading at various mean stress (${\sigma}_{amp}$) and stress amplitude (${\sigma}_{mean}$) conditions. Different S vs. N and da/dN vs. ${\Delta}K$ relations were obtained depending on the loading condition. The higher fatigue strength and the higher resistance of crack growth are seen for the PC samples cyclically loaded at the higher mean stress and lower stress amplitude due to the low crack driving force. Non-linear S - N relationship was detected in the examination of the fatigue properties with changing the mean stress. This is attributed to the different crack growth rate (longer fatigue life): the sample loaded at the high mean stress with lower stress amplitude. Even if the higher stress amplitude, the low fatigue properties are obtained for the sample loaded at the higher mean stress. This was due to the accumulated strain energy to the sample, where severe plastic deformation occurs instead of crack growth (plasticity-induced crack closure). Shear bands and discontinuous crack growth band (DGB) are observed clearly on the fracture surfaces of the sample cyclically loaded at the high stress amplitude, where the lower the ${\sigma}_{mean}$, the narrower the shear band and DGB. On the other hand, final fracture occurred instantly immediately after the short crack growth occurs in the PC sample loaded at the high mean with the low ${\sigma}_{amp}$, i.e., tear fracture, in which the shear bands and DGB are not seen clearly.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집 특별세미나,특별/일반세션
• /
• pp.369-375
• /
• 2009

The Periodic replacements criterion of rail is calculated on the basis of the research result of RTRI in Japan. It is suggested that the service life of the continuous welded rail(CWR) is estimated by the relationship between the rail surface irregularity according to the accumulated passing tonnage and bending fatigue of welded part in CWR. In order to establish the periodic replacements criterion of CWR, this study measured the rail surface irregularity according to the accumulated passing tonnage, the types of track system and welding. Therefore, it is analyzed that the gas pressure welding is the worst one of the others. In addition, it is analyzed that the rail surface irregularity growth rate in ballast track is about $0.02{\sim}0.03mm$/100MGT and its in concrete track is about $0.005{\sim}0.02mm$/100MGT Finally, the result of this study is able to use the basis data to establishing the periodic replacements criterion of CWR considering rail grinding.

• 한국철도학회논문집
• /
• 제17권3호
• /
• pp.193-200
• /
• 2014

본 연구에서는 도시철도 콘크리트궤도 장대레일에 대한 실내피로시험을 수행하였고, 장대레일 잔존수명을 표현한 파괴확률 50% S-N 선도는 적은 실험데이터에 대한 가중치 확률 해석기법을 사용하여 도출하였다. 여기서 피로시험에 사용된 레일들이 누적통과톤수가 서로 다르기 때문에 누적통과톤수를 평균하여 반복횟수를 수정하였다. 또한, 레일표면요철 및 열차속도를 고려한 레일 저부 휨응력은 기존 연구결과 도출된 레일휨응력 예측식을 사용하여 콘크리트궤도 장대레일의 잔존수명을 평가하였다. 레일 피로수명 평가결과, 레일 피로수명이 기준치에 비해 약 2억톤이상 높았다. 또한, 자갈궤도에 비해 콘크리트궤도 레일의 피로수명이 약 3억톤이상 높은 것으로 분석되었다. 따라서 도시철도에서 레일교체기준을 자갈궤도와 콘크리트궤도로 구분할 필요가 있으며, 레일연마를 통한 레일관리가 이루어진다면 기준치가 아닌 목표치로 관리할 수 있을 것으로 판단되었다.

• 한국강구조학회 논문집
• /
• 제20권6호
• /
• pp.723-730
• /
• 2008

철도교량은 무거운 축하중이 작용하여 구조부재의 전체 강도에서 활하중이 차지하는 비율이 높기 때문에 피로에 의한 손상이 클 뿐만 아니라 계속적으로 변화하는 하중환경에 의해 피로손상이 빠르게 진행될 가능성이 있으므로 이에 대한 안전성을 체계적이고 분석적으로 평가할 수 있는 방법이 요구된다. 철도교량에서 구조부재별 피로균열의 생성위치 및 성장속도는 발생응력의 범위와 횟수, 구조시스템의 강성에 관련되어 있다. 구조시스템의 강성은 계획주체, 설계자, 시공자, 유지관리주체 각각의 특성과 불확실성을 포함하고 있으며, 시간의존적 하중과 저항의 특성에 의해서 추계학적으로 변화하게 된다. 그러므로 이러한 하중 및 저항에서의 각각의 불확실성을 정량적이고 객관적으로 표현할 수 있는 신뢰성에 기초한 평가기법을 개발하였다. 철도 및 지하철교량 등의 피로파괴에 대한 확률론적 평가를 위하여 응답면 기법(Response Surface Method, RSM)과 일계이차 모멘트 기법(First Order Second Moment method, FOSM)을 사용하여 피로균열진전과 잔존수명을 평가하였다. 응력변동 범위를 설계변수로 변화시키면서, 중요한 설계입력 변수로 한계상태 방정식을 구성하고 다양한 피로 수명(100년, 75년 등)후의 파괴확률을 예측하여 설계피로수명에 대한 신뢰성 지수계산 및 발생확률을 분석사례로 제시하였다.

• 대한조선학회논문집
• /
• 제49권4호
• /
• pp.350-358
• /
• 2012

This paper deals with accuracy of accumulated fatigue damage estimation using stochastic fatigue analysis method based on Rayleigh PDF. From full scale measurement data on an 8100TEU container vessel, zero-order spectral moments for wave- and vibration-induced energy spectral densities are determined on the probability level of 99%. 80 simulation cases in total are prepared according to the variation of ratio of zero-order spectral moments and center frequency of vibration ESD. By using inverse Fourier transformation and rainflow cycle counting for the combined ESD of wave and vibration, exact fatigue damages are derived. Fatigue damages in frequency domain based on Rayleigh PDF show large conservativeness compared to exact fatigue damages in times domain. The main cause of the excessive conservativeness is analyzed by two aspects: ratio of zero crossing and peak frequencies and ratio of initial zero order spectral moments and zero order spectral moments from rainflow stress range distributions. Finally, a guideline of applicability of Rayleigh PDF is proposed for wide band processes.

• 대한조선학회논문집
• /
• 제49권4호
• /
• pp.359-366
• /
• 2012

This is the final one of the two companion papers dealing with accuracy of accumulated fatigue damage estimation under wide band process. It is stated that four kinds of wide band models exist: typed of equivalent stress, combined PDF, correction factor, and damage combination. For the idealized ESDs from full scale measurement data on an 8100TEU container vessel, fatigue damages are compared for a narrow band prediction model based on Rayleigh PDF and five wide band fatigue prediction models of Dirlik, Wirsching-Light, Jiao-Moan, Benasciutti and DNV. DNV model consistently overestimates fatigue damages regardless of variation of ESDs. Predictions by Jiao-Moan model, which is understood as standard method for design of offshore platforms, are also in conservative side. Best accuracy is found from the results by Dirlik and Benasciutti models, but Benasciutti model is preferred since it can easily combined with narrow band fatigue damage based on Rayleigh PDF.

• 한국응급구조학회지
• /
• 제12권3호
• /
• pp.71-86
• /
• 2008

Purpose : This study was to examine the influence of job stress of 119 Emergency Medical Technician on fatigue and job satisfaction. Methods : Subjects of this study were 228 Emergency Medical Technicians who worked at 119 Safety Center of total 92 fire stations in 12 cities of Gyeonggido including U, N, H, B, A, S, Y, G, G, G, P and I and the period of data collection was from July 11 to Sep. 10, 2007. Collected data were analyzed with SPSS 14.0 version. Results : Conclusions of this study were as follows. 1) Factor related to organization among job stress factors had the greatest influence on fatigue (B = 0.334, p < 0.01), followed by crisis situation factor (B = 0.2042, p < 0.01), inappropriate treatment factor (B = 0.174, p < 0.05), role conflict factor as special job (B = 0.109, p < 0.05) and professional knowledge and technique factor (B = 0.109, p < 0.05), and the influence of job stress factors on fatigue was explained as $R^2=0.340$. 2) Mental burden factor of job stress factors had the greatest influence on job satisfaction (B = -0.606, p < 0.01), followed by organization factor (B = -0.473, p < 0.01) and interpersonal relation and conflict factor (B = -0.339, p < 0.01), and the influence of job stress factor on fatigue was explained as $R^2=0.308$. Conclusions : Job stress of 119 rescuer is increasing continuously and such an accumulated stress lowers the job efficiency. In order to reduce, job stress, it is important to extend(${\rightarrow}$ have) proper self-development, maintain close relationships and mutual correlations among members of organization in personal dimension and to solve the role conflicts, define the organizational roles and simplify excessive job description into concrete work.

• Restorative Dentistry and Endodontics
• /
• 제37권2호
• /
• pp.74-78
• /
• 2012

Objectives: This study aimed to evaluate the relationship between the cyclic fatigue of a K3 file and internal stress intentionally induced until the activation of the autostop function of the torque-controlled motor. Materials and Methods: K3 (Sybron Endo) .04 and .06 taper, size 25, 30, 35, 40 and 45 were used in this study. To give the internal stress, the K3 files were put into the .02 taper Endo-Training-Bloc (Dentsply Maillefer) until the activation of the auto-stop function of the torque-controlled motor. The rotation speed was 300 rpm and torque value was 1.0 $N{\cdot}cm$. K3 were grouped by the number of induced internal stress and randomly distributed to 4 experimental groups (n = 10, Stress 0 [control], Stress 1, Stress 2 and Stress 3). For measuring the cyclic fatigue failure, the K3 files were worked against a sloped glass block and time for file separation was recorded. Data was statistically analyzed Statistical analyses were performed using two-way ANOVA and Duncan post-hoc test at p < 0.05 level. Results: Except .04 taper size 30 in Stress 1 group, there were statistically significant differences in time for file separation between control and all experimental groups. K3 with .04 taper showed higher cyclic fatigue resistance than those of .06 taper. Conclusion: In the limitation of this study, the cyclic fatigue of the K3 file was influenced by the accumulated internal stress from use until the auto-stop function was activated by the torque-controlled motor. Therefore, clinicians should avoid the reuse of the K3 file that has undergone auto-stops.

• 산업기술연구
• /
• 제9권
• /
• pp.21-28
• /
• 1989

For the study of the fatigue behavior, high-strength bolted connections on a small scale were manufactured, and carried on fatigue tests. Its experimental values were analysed by stress-fatigue life (S-N) curve. Three types of specimens : the base metal, the cireular hole and the welded sperimens had same net section were made. Through the same tests those experimental values were compared with those of the high-strength bolted conneetions. The results of these studies are as followings. It was found that the fatigue strength in $F_{n=100,000}$ and $F_{n=2,000,000}$ of the high-strength bolted conneetions were much more about 14% and 16% than that of the base metal specimen. It was thought that this trend was due to frictional force increasing fatigue strength. It was known that fatigue strength in $F_{n=100,000}$ and $F_{n=2,000,000}$ of the welded joints were less 29% and 21% than that of base metal specimen. It was thought that that trend was due to weld flaw. It was appeared that the fatigue strength in $F_{n=100,000}$ and $F_{n=2,000,000}$ of the high-strength bolted connections were much more about 38% and 30% than that of welded joint. It was thought that it was due to both frictional force increasing the fatigue strength in bolted connections and weld flaw decreasing the fatigue strength in welded connections. It was found that the fatigue strength in $F_{n=100,000}$ and $F_{n=2,000,000}$ of the B3 specimens were much more 2% and -2% than that of the B4 specimen. It was thought that that trend was due to the frictional force, which concerned with shape of specimen. It was known that the fatigue strength in $F_{n=100,000}$ and $F_{n=2,000,000}$ of the specimen with circular hole was less 61% and 65% than that of base metal. It was known that the allowable stress for bolted joint was higher than that of welded Joints. If that research is continued and more data are accumulated it can be expected that a basic pattern to provided the indicator of the fatigue design of the bolted connections of steel structures and persume the safety and lifeproof of existing structures is given.

• 한국산업융합학회 논문집
• /
• 제7권4호
• /
• pp.399-405
• /
• 2004

Currently, the use of carbon steel in a high temperature environment, such atomic reactor, increases. Test piece was heated in electric furnace and the prescribed temperature was controlled within ${\pm}1^{\circ}C$. Debris that falls apart from cracked section due to friction is accumulated inside. Then, as it causes fretting corrosion (formation of oxide layer), it contributes to crack closure.