• 한국전기전자재료학회논문지
• /
• 제16권7호
• /
• pp.634-640
• /
• 2003

This paper is to be researched into ozone generation character of Bi-Ti-Si type high dielectric yield ceramic catalyst discharge tube. And conditions of basic experiment are the outside diameter of discharge tube : 52 mm, the length of discharge tube : 350 mm, the frequence : 900 Hz, the temperature of cooling water : 25 $^{\circ}C$, quantity of flow : 5, 10, 20 l/min, pressure : 1.2, 1.4, 1.6 atm, and distance of discharge gap : 0.4, 0.6, 0.8 mm. Ozone generation characteristics were measured to consumption power. At quantity of flow : 20 l/min, discharge gap : 0.6 mm, pressure : 1.6, and consumption power : 150 W, Maximum ozone generation efficiency of 175 g/kWh was obtained. Maximum ozone generation efficiency was measured below the flow quantity of 20 l/min at below pressure of 1.6 atm. However, Maximum ozone generation efficiency was measured over the flow quantity of 20 l/min at over pressure of 1.6 atm.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.356-359
• /
• 2003

This paper deals with a flat type ultrasonic motor, which uses a longitudinal-bending multi mode vibrator of rectangular form. This ultrasonic motor was designed by combination of the first longitudinal and eighth bending mode, and the motor consisted of a straight aluminum alloy bar bonded with piezoelectric ceramic elements as a driving element. The geometrical dimensions of the rectangular aluminum vibrator were determined by Euler-Bernoulli theory In the experimental device, piezoelectric ceramics ( a piece of ceramic for the L-mode, $24\;{\times}\;8\;{\times}\;1[mm]$, and four pieces for the B-mode, $12.5\;{\times}\;8\;{\times}\;1[mm]$) were attached to one side of a aluminum plate($100\;{\times}\;8\;{\times}\;1[mm]$), and the stator was supported with a plastic case. As results, no-load rpm was 50[rev./m] when applied voltage was 150[Vrms] at the resonance frequency, and as the voltage was increased, the rpm was increased.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 추계학술대회 논문집
• /
• pp.200-203
• /
• 2000

The application of the ultrasonic nozzle has been extended because it is possible atomization of liquid material. In this study, the characteristics of the ultrasonic nozzle and ceramic oscillator were investigated. The oscillator for the ultrasonic nozzle were made piezoelectric ceramic of Pb[($Sb_{1/2}$ $Nb_{1/2}$)$_{0.035}$-($Mn_{1/3}$$Nb_{2/3}$)$_{0.065}$-($Zr_{0.49}$$Ti_{0.51}$)$_{0.90}$]$O_3$. The electromechanical coupling factor($k_p$) and mechanical quality factor(Qm) showed the values of 0.555, 1, 214 respectively when the Zr/Ti ratio was 49/51. Moreover, this oscillator will have the temperature stability because it's curie temperature is 322[$^{\circ}C$]. The driving current of ultrasonic nozzle showed the value of 80[mA] when the driving time was lO[min.]. Also, The surface temperature of ceramic oscillator showed 80[$^{\circ}C$] at driving time lO[min.] We knew that the ultrasonic nozzle had stabile driving above 10[min.].

• Transactions on Electrical and Electronic Materials
• /
• 제9권1호
• /
• pp.33-37
• /
• 2008

This paper describes the development of a new $5.0{\times}3.2mm$ SAW filter bank which is consist of 12 L, C matching components and 4 SAW bare chips on PCB substrate with CSP technology. We improved the manufacturing cost by removing the ceramic package through direct flip bonding of $LiTaO_3$ SAW bare chip on PCB board after mounting L, C passive element on PCB board. After that we realized the hermitic sealing by laminating the epoxy film. To confirm the confidentiality and durability of the above method, we have obtained the optimum flip bonding & film laminating condition, and figured out material property and structure to secure the durability & moisture proof of PCB board. The newly developed super mini $5.0{\times}3.2mm$ filter bank shows the superior features than those of existing products in confidence, electrical, mechanical characters.

• 한국세라믹학회지
• /
• 제48권2호
• /
• pp.178-182
• /
• 2011

The Rutile - type brown pigments doped with chromium were synthesized. Samples of $Ti_{1-x}Cr_xO_2$ ($0.02{\leq}X{\leq}0.08$) were synthesized by the solid state method. Solid solution limit of Cr contents to the rutile structure and its coloration were studied. Optimum composition was investigated accordingly. The characteristics of synthesized pigments were analyzed by XRD, SEM, Raman spectroscopy and UV. As a result, single phase of Rutile was observed from $1000^{\circ}C$ by XRD. The maximum limit of solid solution was 0.06 mole $Cr_2O_3$. The glazed sample showed brown color, and the value of CIE $L^*a^*b^*$ was $L^*$ 33.27, $a^*$ 10.64, $b^*$ 20.84.

• Transactions on Electrical and Electronic Materials
• /
• 제11권5호
• /
• pp.206-211
• /
• 2010

Piezoelectric energy harvesting uses piezoelectric, which is able to convert unused mechanical vibration energy to electrical energy, such as with motor and machinery. The piezoelectric energy harvester was constructed with a cantilever made of lead zirconate titanate with a metal plate. The primary material was soft lead zirconium titanate (PZT-5H) due to the large strain availability, acceptable mechanical strength and high piezoelectric constant. This technique's drawback is that the energy efficiency is lower than the other energy harvesting methods, but this study increases the output electric power efficiency by analyzing a finite element method for the structure of the piezoelectric energy harvester. We manufactured two cantilever types as follows: the L-60 and L-33 bimorph piezoelectric energy harvesters. Their resulting energy harvesters were able to obtain high voltage values as follows: 27.4 mV and 40.6 mV. Moreover, these results have a similar band of resonance frequency it comparison to the simulation. Consequently, this study was confirmed with validity. The output electric powers of the L-60 and L-33 types have 3.1 mW/s and 5.8 mW/s with 47 Hz and 148 Hz of resonance frequency and then, the load resistivities were $100k\Omega$ and $10k\Omega$, respectively.

• 자원리싸이클링
• /
• 제14권4호
• /
• pp.3-9
• /
• 2005

석란광산에서 발생되는 선탄폐석을 효율적으로 이용하기 위하여 세라믹스 원료 소재로의 활용 가능성을 고찰하였다. 석탄폐석의 첨가량이 증가함에 따라 소성 시험편의 소성수축률이 저하되고, 압축강도는 약간 감소하는 등의 효과와 선탄페석에 함유되어 없는 탄소분의 연소에 의한 기공의 증가로 제품의 경량화도 가능한 것으로 판단되었다. 선탄폐석의 첨가량을 변화시켜 $1,150^{\circ}C$ 이상에서 소성한 경우 흡수율은 $10\;wt\%$ 이하를 나타내었고, 압축강도는 모두 21MPa이상으로 KS L 4201에서 규정한 1종 점토벽돌의 기준에 모두 적합함을 확인할 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.1005-1009
• /
• 2001

The application of the ultrasonic nozzle has been extended because it is possible atomization of liquid material. In this study, the driving characteristics of the ultrasonic nozzle on the driving circuit were investigated. And the characteristics of the ceramic oscillator were investigated for the temperature stability. The ceramic oscillator were made the Pb[(Sb$\sub$1/2/,Nb$\sub$1/2/)$\sub$0.035/-(Mn$\sub$1/3/Nb$\sub$2/3/)$\sub$0.065/- (Zr$\sub$x/Ti$\sub$l-x/)$\sub$0.9/]O$_3$with mole ratio of Zr/Ti. The ceramis oscillator were need the curie temperature of the over 300[$^{\circ}C$] for the temperature stability. When the Zr/Ti ratio was 49/51, it's curie temperature is 322[$^{\circ}C$] and the electromechanical coupling factor(k$\sub$p/) and mechanical quality factor(Q$\sub$m/) showed the values of 0.555, 1,214, respectively The resonance frequency of ceramic oscillator were from 40KHz to 45KHz. So that, the driving circuit were made a possibility that the frequency are variable. The driving current of ultrasonic nozzle showed the value of maximum 80[mA]. Also, The surface temperature of ceramic oscillator showed 80[$^{\circ}C$] at driving time 10[min]. We knew that the ultrasonic nozzle had stabile driving above 10[min.].

• 한국전기전자재료학회논문지
• /
• 제24권11호
• /
• pp.876-881
• /
• 2011

The sintering, defect and grain boundary characteristics of Bi-based ZnO chip varistor (1,608 mm size) have been investigated to know the possibility of lowering a manufacturing price by using 100 % Ag inner-electrode. The samples were prepared by general multilayer chip varistor process and characterized by shrinkage, SEM, current-voltage (I-V), admittance spectroscopy (AS), impedance and modulus spectroscopy (IS & MS) measurement. There are no problems to make a chip varistor with 100% Ag inner-electrode in the sintering temperature range of 850~900$^{\circ}C$ for 1 h in air. A good varistor characteristics ($V_n$= 9.3~15.4 V, a= 23~24, $I_L$= 1.0~1.6 ${\mu}A$) were revealed but formed $Zn_i^{{\cdot}{\cdot}}$(0.209 eV) as dominant defect, and increased the distributional inhomogeneity and the temperature instability in grain boundary barriers.

• 한국치위생학회지
• /
• 제16권5호
• /
• pp.695-700
• /
• 2016

Objectives: The purpose of the study was to investigate the effect of CAD/CAM ceramic thickness on shade. Methods: 24 disk-shaped ceramic specimens (E.Max CAD & Empress CAD, $12mm{\times}12mm$) were prepared and divided into 4 groups (n=6). Ceramic specimens in 2 thicknesses (0.8 mm, 1.0 mm) were made low translucency(LT) shade A2. All specimens were measured as L*, a*, b* using spectrophotometer. The color differences(${\Delta}E$ values) between the specimen and a control target block ($12{\times}12{\times}1.2mm$) were calculated. Two-way ANOVA performed between 2 groups(material and thickness). Results: As the thickness increased, the $L^*$ (for all groups) and $b^*$ value (for all groups) increased and the $a^*$ value(for LR group) decreased. The mean color differences caused by thickness was acceptible (${\Delta}E$ > 2) for group LD1. But the mean color differences by thickness were not selected (${\Delta}E$ < 2) for group LD2, LR1, LR2. Conclusions: The different thickness can influence the final color of CAD/CAM ceramic.