• 한국도로학회논문집
• /
• 제19권5호
• /
• pp.69-75
• /
• 2017

PURPOSES : The purpose of this study is to evaluate different types of Ground Penetrating Radar (GPR) testing for characterizing the road cavity detection. The impulse and step-frequency-type GPR tests were conducted on a full-scale testbed with an artificial void installation. After analyzing the response signals of GPR tests for detecting the road cavity, the characteristics of each GPR response was evaluated for a suitable selection of GPR tests. METHODS : Two different types of GPR tests were performed to estimate the limitation and accuracy for detecting the cavities underneath the asphalt pavement. The GPR signal responses were obtained from the testbed with different cavity sizes and depths. The detection limitation was identified by a signal penetration depth at a given cavity for impulse and step-frequency-type GPR testing. The unique signal characteristics was also observed at cavity sections. RESULTS : The impulse-type GPR detected the 500-mm length of cavity at a depth of 1.0 m, and the step-frequency-type GPR detected the cavity up to 1.5 m. This indicates that the detection capacity of the step-frequency type is better than the impulse type. The step-frequency GPR testing also can reflect the howling phenomena that can more accurately determine the cavity. CONCLUSIONS :It is found from this study that the step-frequency GPR testing is more suitable for the road cavity detection of asphalt pavement. The use of step-frequency GPR testing shows a distinct image at the cavity occurrences.

• Structural Engineering and Mechanics
• /
• 제16권5호
• /
• pp.597-612
• /
• 2003

In this paper, multi-story buildings with shear-wall structures and with narrow rectangular plane configuration are modeled as a multi-step flexural-shear plate with varying cross-section for buckling analysis. The governing differential equation of such a plate is established. Using appropriate transformations, the equation is reduced to analytically solvable equations by selecting suitable expressions of the distribution of stiffness. The exact solutions for buckling of such a one-step flexural-shear plate with variable stiffness are derived for several cases. A new exact approach that combines the transfer matrix method and closed from solution of one-step flexural-shear plate with continuously varying stiffness is presented for stability analysis of multi-step non-uniform flexural-shear plate. A numerical example shows that the present methods are easy to implement and efficient.

• 한국기계가공학회지
• /
• 제7권3호
• /
• pp.30-35
• /
• 2008

As demands for being economical, precise drilling process is on the increase. Therefore, the objective of this study is to develop a step cutter that can be controllable through micro dimension and can be changed from separate manufacturing processes of drilling and boring into an integrated one. In order to attain this object the step cutter is designed with a 3D geometric modeling and the design could be modified easily by using parametric modeling methodology. Also, collision is not occurred during manufacturing process because of cutting simulation. The step cutter is assembled by parts made up of 5-axis machining and sintering. Validation tests are accomplished. They show that developed cutter has characteristics such as reduction of machining time as well as the good surface roughness of the machined hole. Indeed, reliability could be obtained from a durability test.

• 대한기계학회논문집A
• /
• 제25권12호
• /
• pp.1974-1980
• /
• 2001

The control algorithm of a new type self-bearing step motor is presented. The motor actuator is used for both motor and bearing functionality without any redundant coil windings or redundant electromagnets. The self$.$bearing step motor layout and its control method are described. A linearized farce-current-displacement relationship is derived. As the result of the unbalance response approach, the constant torque production is possible fur the supply current regulation algorithm. And even if the bearing functionality is added in the motor functionality, no additional current for bearing functionality is possible, and this leads to minimize the net power loss. Also, the unbalance response shows the independent bearing force and motor torque.

• 한국자동차공학회논문집
• /
• 제22권6호
• /
• pp.39-48
• /
• 2014

Variable valve actuation system is one of the widely used techniques to improve the fuel efficiency and power of automotive engines. 2-step variable valve actuation systems are also paid attention for the application to direct acting type valve train systems. Besides its advantages in size, weight, relatively simple structure, ets, however, 2-step variable valve actuation system has inherent disadvantages in dynamic instability of switching system to alter discontinuous lift modes. In this study, both experimental and analytical studies are performed to understand the dynamic behavior of a switching mechanism of a 2-step variable valve actuation system, and present a design method to improve its dynamic instability.

• Steel and Composite Structures
• /
• 제29권1호
• /
• pp.139-149
• /
• 2018

In this paper a new multi-step damage detection approach is provided. In the first step, condensed modal residual vector based indicator (CMRVBI) has been proposed to locate the suspected damaged elements of structures that have rotational degrees of freedom (DOFs). The CMRVBI is a new indicator that uses only translational DOFs of the structures to localize damaged elements. In the next step, salp swarm algorithm is applied to quantify damage severity of the suspected damaged elements. In order to assess the performance of the proposed approach, a numerical example including a three-layer square laminated composite plate is studied. The numerical results demonstrated that the proposed CMRVBI is effective for locating damage, regardless of the effect of noise. The efficiency of proposed approach is also compared during both steps. The results demonstrate that in noisy condition, the damage identification approach is capable for the studied structure.

• Asia pacific journal of information systems
• /
• 제9권2호
• /
• pp.19-37
• /
• 1999

Computer aided process planning(CAPP) is a key for implementing CIM. It is bridge between CAD and CAM and translates the design information into manufacturing instructions. Generally, manufacturing is an area where intelligent systems will not be able to rely on methods requiring formalized knowledge. Manufacturing lacks a body of knowledge that is specific, formalized, and rigorous, and which can be coded as rules or procedures. Thus expertise in manufacturing is developed over a period of many years. Case-based reasoning(CBR) offers a new approach for developing intelligent system. In the case-based approach the problem solving experience of the experts is encoded in the form of cases. CBR's retrieval process can be divided to two step. The first step is matching step, and the second step is selection step. For selecting base case, new preference heuristics were introduced using similarity concept. Similarity concept has three has three dimensions, i.e. entity similarity, structural similarity, and goal similarity. In this paper, bolt's process planning was selected an application domain. Following the test result, the new preference heuristics were approved as a useful procedure in CAPP.

• Journal of Mechanical Science and Technology
• /
• 제14권5호
• /
• pp.547-552
• /
• 2000

The objective of this paper is to present a modified fractional step method of keeping a constant mass flow rate in spatially periodic flows, because original fractional step methods do not precisely keep the mass flow rate constant in time. In the modified method, the mean and fluctuating pseudo-pressure gradients are separately obtained at each time step. This method is successfully applied to channel and pipe flows and shown to be suitable for maintaining a constant mass flow rate in time.

• 대한산업공학회지
• /
• 제28권4호
• /
• pp.435-442
• /
• 2002

It is difficult to access and share design data among heterogeneous CAD systems. Usually, different CAD systems exchange the design data using a neutral format such as IGES or STEP. A prototype CAD system which uses a geometric kernel and a commercial database management system has been implemented. The prototype system used the Open Cascade geometric kernel and the commercial object-oriented database ObjectStore. STEP provides the database schema. The database can be accessed from commercial CAD systems such as SolidWorks or Unigraphics. The data access module from a commercial CAD system is developed with the CAD system's native API, ObjectStore API functions, and ActiveX.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 A
• /
• pp.400-402
• /
• 1995

A novel type of single phase multi-step inverter is proposed, which has twelve-stepped levels of the output voltage. In this inverter the waveform of the output votage has smaller harmonic contents than those of a conventional six-step inverter. In this paper a new multi-step technique is analyzed. This new multi-step technique of the twelve-stewed single phase voltage source inverter has the advantage compared with the conventional six-step inverter, and the experimental results are proved by the calculation using spectrum-analyzer.