• 한국전기전자재료학회논문지
• /
• 제16권2호
• /
• pp.102-107
• /
• 2003

This study puts focus on the optimization of growth temperature of CIGS absorber layer which affects severely the performance of solar cells. The CIGS absorber layers were prepared by three-stage co-evaporation of metal elements in the order of In-Ga-Se. The effect of the growth temperature of 1st stage was found not to be so important, and 350$^{\circ}C$ to be the lowest optimum temperature. In the case of growth temperature at 2nd/3rd stage, the optimum temperature was revealed to be 550$^{\circ}C$. The XRD results of CIGS films showed a strong (112) preferred orientation and the Raman spectra of CIGS films showed only the Al mode peak at 173cm$\^$-1/. Scanning electron microscopy results revealed very small grains at 2nd/3rd stage growth temperature of 480$^{\circ}C$. At higher temperatures, the grain size increased together with a reduction in the number of the voids. The optimization of experimental parameters above mentioned, through the repeated fabrication and characterization of unit layers and devices, led to the highest conversion efficiency of 15.4% from CIGS-based thin film solar cell with a structure of Al/ZnO/CdS/CIGS/Mo/glass.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 일렉트렛트 및 응용기술
• /
• pp.108-111
• /
• 2002

CIGS film has been fabricated on soda-lime glass, which is coated with Mo film. by multi-source evaporation process. The films has been prepared with thickness of 1.0 ${\mu}m$, 1.75${\mu}m$, 2.0${\mu}m$, 2.3${\mu}m$, and 3.0${\mu}m$. X-ray diffraction analysis with film thickness shows that CIGS films exhibit a strong (112) preferred orientation. Furthermore. CIGS films exhibited distinctly decreasing the full width of half-maximum and (112) preferred peak with film thickness. Also, The film's microstructure, such as the preferred orientation, the full width at half-maximum(FWHM), and the interplanar spacing were examined by X-ray diffraction. The preparation condition and the characteristics of the unit layers were as followings ; Mo back contact DC sputter, CIGS absorber layer : three-stage coevaporation, CdS buffer layer : chemical bath deposition, ZnO window layer : RF sputtering, $MgF_2$ antireflectance : E-gun evaporation

• 반도체디스플레이기술학회지
• /
• 제16권4호
• /
• pp.59-62
• /
• 2017

In this paper, atmospheric pressure plasma treatment was proposed for high performance indium gallium zinc oxide thin film transistor (IGZO TFT). RF Ar plasma treatment is performed at room temperature under atmospheric pressure as a simple and cost effective channel surface treatment method. The experimental results show that field effect mobility can be enhanced by $2.51cm^2/V{\cdot}s$ from $1.69cm^2/V{\cdot}s$ to $4.20cm^2/V{\cdot}s$ compared with a conventional device without plasma treatment. From X-ray photoelectron spectroscopy (XPS) analysis, the increase of oxygen vacancies and decrease of metal-oxide bonding are observed, which suggests that the suggested atmospheric Ar plasma treatment is a cost-effective useful process method to control the IGZO TFT performance.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제15권2호
• /
• pp.249-254
• /
• 2015

Solution-derived amorphous indium-gallium-zinc oxide (a-IGZO) thin-film-transistor (TFTs) were developed using a microwave irradiation treatment at low process temperature below $300^{\circ}C$. Compared to conventional furnace-annealing, the a-IGZO TFTs annealed by microwave irradiation exhibited better electrical characteristics in terms of field effect mobility, SS, and on/off current ratio, although the annealing temperature of microwave irradiation is much lower than that of furnace annealing. The microwave irradiated TFTs showed a smaller $V_{th}$ shift under the positive gate bias stress (PGBS) and negative gate bias stress (NGBS) tests owing to a lower ratio of oxygen vacancies, surface absorbed oxygen molecules, and reduced interface trapping in a-IGZO. Therefore, microwave irradiation is very promising to low-temperature process.

• Transactions on Electrical and Electronic Materials
• /
• 제17권3호
• /
• pp.143-145
• /
• 2016

In order to find suitable source and drain (S/D) electrodes for amorphous InGaZnO thin film transistors (a-IGZO TFTs), the specific contact resistance of interface between the channel layers and various S/D electrodes, such as Ti/Au, a-IZO and multilayer of a-IGZO/Ag/a-IGZO, was investigated using the transmission line model. The a-IGZO TFTs with a-IGZO/Ag/a-IGZO of S/D electrodes had good performance and low contact resistance due to the homo-junction with channel layer. The stability was measured with different electrodes by a positive bias stress test. The result shows the a-IGZO TFTs with a-IGZO/Ag/a-IGZO electrodes were more stable than other devices.

• Journal of Information Display
• /
• 제11권3호
• /
• pp.113-118
• /
• 2010

The effect of hydrogen in the alumina gate insulator on the bottom gate oxide thin film transistor (TFT) with an InGaZnO film as the active layer was investigated. TFT with more H-containing alumina films (TFT A) fabricated via atomic layer deposition using a water precursor showed higher stability under positive and negative bias stresses than that with less H-containing alumina deposited using ozone (TFT B). While TFT A was affected by the pre-vacuum annealing of GI, which resulted in $V_{th}$ instability under NBS, TFT B did not show a difference after the pre-vacuum annealing of GI. All the TFTs showed negative-bias-enhanced photo instability.

• Journal of Information Display
• /
• 제13권4호
• /
• pp.179-183
• /
• 2012

In this paper, a gate driver circuit for In-Ga-Zn-O thin-film transistors (TFTs) driven by only two clock signals is reported. In this circuit, the TFTs are turned off with a negative $V_{GS}$ by the two clock signals. As a result, it works properly and suppresses power consumption increase even though the TFT $V_T$ shifts in the negative direction.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.705-705
• /
• 2013

CIGS 박막태양 전지는 I-III-VI Chalcopyrite 결정구조를 가진 화합물 반도체 태양전지로 인위적인 밴드갭 조작을 통하여 효율 향상에 용이하다. 4원소 화합물인 CIGS 광흡수층의 대표적인제조 방법으로는 co-evaporation 공정법이 있다. 동시 증발법은 CIGS 결정을 최적화하기 위하여 박막이 증착되는 동안 기판의 온도를 3단계로 변화시켜주는 3-stage 공정을 통하여 제작된다. 일반적으로 CIGS 박막태양전지는 전면전극으로 투명전도막이 사용되며 높은 광투과성과 전기전도성을 가져야 한다. 투명전도막의 광학적, 전기적 특성은 CIGS 박막태양전지의 효율에 영향을 미치기 때문에 최적화된 조건이 요구된다. 본 연구에서는 CIGS 광흡수층은 Ga/(In+Ga)=0.31, Cu/(In+Ga)=0.86으로 최적화 시켰으며, 투명전도막은 Ga이 도핑된 ZnO박막을 RF 마그네트론 스퍼터링법을 이용하여 증착하였다. CIGS 박막 태양전지 직렬저항 성분인 투명 전도막의 비저항이 $4.46{\times}{\square}10{\square}-3{\square}$(${\Omega}$-cm)에서 $9.3{\times}{\square}0{\square}-4{\square}$(${\Omega}$-cm) 으로 변화함에 따라 Efficiency가 9.67%에서 16.47%으로 증가하였으며, Voc가 508 mV에서 596 mV으로, Jsc가 29.27 mA/$cm^2$에서 37.84 mA/$cm^2$으로, FF factor가 64.99%에서 72.96%로 증가하였다. 이에 따른 투명 전도막의 전기적, 광학적 특성을 통해 CIGS 박막태양전지에 미치는 영향에 대해 조사하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.426-426
• /
• 2012

The CIGS absorber has outstanding advantages in the absorption coefficient and conversation efficiency. The CIGS thin film solar cells have been researched for commercialization and increasing the conversion efficiency. CIG precursors were deposited on the Mo coated glass substrate by magnetron sputtering with multilayer structure, which is CuIn/CuGa/CuIn/CuGa. Then, the metallic precursors were selenized under high Se pressure by RTP method which included. Se vapor was supplied using Se cracker cell instead of toxic hydrogen selenide gas. Se beam flux was controlled by variable reservoir zone (R-zone) temperature during selenization process. Cracked Se source reacted with CIG precursors in a small quantity of Se because of small size molecules with high activation energy. The CIGS thin films were studied by FESEM, EDX, and XRD. The CIGS solar cell was also developed by layering of CdS and ZnO layers. And the conversion efficiency of the CIGS solar cell was characterization. It was reached at 6.99% without AR layer.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.464.1-464.1
• /
• 2014

Among numerous material candidates, Cu(InxGa1-x)(SySe2-y) (CIGS) thin films have emerged as promising material candidates for thin film solar cell applications due to the high energy conversion efficiency and relatively low fabrication cost. The CIGS thin film solar cells consist of several materials, including Mo back contacts, ZnO-based window layers, and CdS buffer layers. All these materials have different crystal structures and contain quite distinct chemical elements, and hence the device characterization requires careful analyses. Most of all, identification of the major trap states resulting in the carrier recombination processes is a key step toward realization of high efficiency CIGS solar cells. We have carried out electrical investigations of CIGS thin film solar cells to specify the major trap states and their roles in photovoltaic performance. In particular, we have used the temperature-dependent transport characterizations and admittance spectroscopy. In this presentation, we will introduce some exemplary studies of DC and AC electrical characteristics of the CIGS solar cells.