Kim, Ik Hyun;Dan, Seungkyu;Cho, Seonghyun;Lee, Gibaek;Yoon, En Sup
Korean Chemical Engineering Research
/
v.52
no.4
/
pp.467-474
/
2014
Preliminary design in chemical process furnishes economic feasibility through calculation of both mass balance and energy balance and makes it possible to produce a desired product under the given conditions. Through this design stage, the process possesses unchangeable characteristics, since the materials, reactions, unit configuration, and operating conditions were determined. Unique characteristics could be very economic, but it also implies various potential risk factors as well. Therefore, it becomes extremely important to design process considering both economics and safety by integrating process simulation and quantitative risk analysis during preliminary design stage. The target of this study is LNG liquefaction process. By the simulation using Aspen HYSYS and quantitative risk analysis, the design variables of the process were determined in the way to minimize the inherent explosion risks and operating cost. Instead of the optimization tool of Aspen HYSYS, the optimization was performed by using stochastic optimization algorithm (Covariance Matrix Adaptation-Evolution Strategy, CMA-ES) which was implemented through automation between Aspen HYSYS and Matlab. The research obtained that the important variable to enhance inherent safety was the operation pressure of mixed refrigerant. The inherent risk was able to be reduced about 4~18% by increasing the operating cost about 0.5~10%. As the operating cost increases, the absolute value of risk was decreased as expected, but cost-effectiveness of risk reduction had decreased. Integration of process simulation and quantitative risk analysis made it possible to design inherently safe process, and it is expected to be useful in designing the less risky process since risk factors in the process can be numerically monitored during preliminary process design stage.
Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
/
2001.07a
/
pp.143-148
/
2001
PbWO$_4$ can be densified at 85$0^{\circ}C$ and it shows fairy good microwave dielectric properties; dielectric constant($\varepsilon$$_{r}$) of 21.5, quality factor(Q $\times$f$_{0}$) of 37,224 GHz, and temperature coefficient of resonant frequency($\tau$/suf f/) of -31ppm/$^{\circ}C$. Due to its low sintering temperature, PbWO$_4$ can be used as a multilayered chip component at microwave frequency with high electrical performance by using high conductive electrode metals such as Ag and Cu. However, in order to use this material for microwave communication devices, the $\tau$$_{f}$ of PbWO$_4$ must be stabilized to near zero with high Q$\times$f$_{0}$. In present study, PbWO$_4$ was modified by adding TiO$_2$, B$_2$O$_3$, and CuO in order to improve the microwave dielectric properties without increasing the sintering temperature. The addition of TiO$_2$ increased the $\tau$$_{f}$ and $\varepsilon$$_{r}$, due to its high rr(200ppm/$^{\circ}C$) and $\varepsilon$$_{r}$(100). However, the addition of TiO$_2$ reduced the Q$\times$f$_{0}$ value. When the mot ratio of PbWO$_4$ and TiO$_2$ was 0.913:7.087, near zero $\tau$$_{f}$(0.2ppm/$^{\circ}C$) was obtaibed with $\varepsilon$$_{r}$=22.3, and Q$\times$f/$_{0}$=21,443GHz. With this composition, various amount of B$_2$O$_3$ and CuO were added in order to improve the quality factor. The addition, of B$_2$O$_3$ decreased the $\varepsilon$$_{r}$. However, increased Q$\times$f$_{0}$ and $\tau$$_{f}$. When 2.5 wt% of B$_2$O$_3$ was added to the 0.913PbWO$_4$-0.087TiO$_2$ ceramic, $\tau$$_{f}$ =8.2, $\varepsilon$$_{r}$=20.3, Q$\times$f$_{0}$=54784 GHz. When CuO added to the 0.913PbWO$_4$-0.087TiO$_2$ ceramic, $\tau$$_{f}$ was continuously decreased. And $\varepsilon$$_{r}$ . and Q$\times$f$_{0}$ were increased up to 1.0 wt% then decreased. At 0.1 wt% of CuO addition, the 0.913PbWO$_4$-7.087Ti0$_2$ Ceramic Showed $\varepsilon$$_{r}$=23.5, $\tau$$_{f}$=4.4ppm/$^{\circ}C$, and Q$\times$f$_{0}$=32,932 GHz.> 0/=32,932 GHz.X>=32,932 GHz.> 0/=32,932 GHz.
Journal of the Society of Cosmetic Scientists of Korea
/
v.33
no.4
/
pp.231-238
/
2007
In the previous study, the anti-oxidant activity of extract/fraction of Sueada asparagoides (SA) was investigated and the results showed that the ethylacetate (EtOAc) fraction and its aglycone fraction had the best performance on the free radical scavenging activity, reactive oxygen species scavenging (ROS) activity and cell protective activity (J. Soc. Cosme. Scientists Korea, 33(3), 145 (2007)). In this study, the stability of cream containing 0.3% SA EtOAc extract (called extract below) was evaluated. pH, viscosity and absorbance (363 nm) were measured under the 4 different temperatures ($0^{\circ}C,\;25{\circ}C,\;37{\circ}C\;and\;45{\circ}C$) and under the sun light at the 4 week intervals during the 12 weeks in total. The control cream without containing the extract did not show pH change under the different temperatures mentioned above. However, the pH of the cream the extract was decreased 0.08 at the temperature ranges of $0^{\circ}C\;to\;37^{\circ}C$. Under the $45^{\circ}C$ and sun light condition, the pH was decreased 0.51 and 0.66, respectively. The cream containing the extract did not show absorbance change at the temperature ranges of 0 to $37^{\circ}C$ for 12 weeks. Instead, the absorbance of the cream treated under $45^{\circ}C$ and sun light condition was decreased 7.6 % and 7.4 %, respectively. This decrease in absorbance is relatively small compared to the 48.3 % decrease of the extract sampled from the cream using ethanol solution. This indicates that the extract is stabilized in the cream. After treating the cream for 12 weeks under the different temperatures, the viscosity was measured for the cream containing the extract and control cream. The values were increased by 1,748 cPs in average compared to the initial value for the former and by 951 cPs in average for the latter. On the other hand, the viscosity of control cream treated under the sun light for 12 weeks was significantly decreased (4,022 cPs) relative to the cream containing the extract, which showed 2,484 cPs increase in viscosity. This indicates that the SA extract contributes to the stability of the emulsion product by protective effect to maintain the viscosity of the cream against sun light. In addition, any change in color or smell was not observed through 12 weeks of the experimental time period. Thus, it is concluded that it is still not clear in the stability of the cream containing the extract when it is stored for the long time. Accordingly, it is suggested that further study is needed to provide more information to the manufactures, who are seeking for the application of the extract to improve the anti-oxidant activity and stability of cosmetic products.
The seismic data quality of marine geological and engineering survey deteriorates because of the sea swell. We often conduct a marine survey when the swell height is about 1 ~ 2 m. The swell effect correction is required to enhance the horizontal continuity of seismic data and satisfy the resolution less than 1 m. We applied the swell correction to the 8 channel high-resolution airgun seismic data and 3.5 kHz subbottom profiler (SBP) data. The correct sea bottom detection is important for the swell correction. To detect the sea bottom, we used maximum amplitude of seismic signal around the expected sea bottom, and picked the first increasing point larger than threshold value related with the maximum amplitude. To find sea bottom easily in the case of the low quality data, we transformed the input data to envelope data or the cross-correlated data using the sea bottom wavelet. We averaged the picked sea bottom depths and calculated the correction values. The maximum correction of the airgun data was about 0.8 m and the maximum correction of two kinds of 3.5 kHz SBP data was 0.5 m and 2.0 m respectively. We enhanced the continuity of the subsurface layer and produced the high quality seismic section using the proper methods of swell correction.
$Ta_2O_5$ thin film IS a promising material for the high dielectrics of ULSI DRAM. In this study, $Ta_2O_5$ thin film was grown on p-type( 100) Si wafer by thermal metal organic chemical vapo deposition ( MCCVD) method and the effect of operating varialbles including substrate temperature( $T_s$), bubbler temperature( $T_ \sigma$), reactor pressure( P ) was investigated in detail. $Ta_2O_5$ thin film were analyzed by SEM, XRD, XPS, FT-IR, AES, TEM and AFM. In addition, the effect of various anneal methods was examined and compared. Anneal methods were furnace annealing( FA) and rapid thermal annealing( RTA) in $N_{2}$ or $O_{2}$ ambients. Growth rate was evidently classified into two different regimes. : (1) surface reaction rate-limited reglme in the range of $T_s$=300 ~ $400 ^{\circ}C$ and (2: mass transport-limited regime in the range of $T_s$=400 ~ $450^{\circ}C$.It was found that the effective activation energies were 18.46kcal/mol and 1.9kcal/mol, respectively. As the bubbler temperature increases, the growth rate became maximum at $T_ \sigma$=$140^{\circ}C$. With increasing pressure, the growth rate became maximum at P=3torr but the refractive index which is close to the bulk value of 2.1 was obtained in the range of 0.1 ~ 1 torr. Good step coverage of 85. 71% was obtained at $T_s$=$400 ^{\circ}C$ and sticking coefficient was 0.06 by comparison with Monte Carlo simulation result. From the results of AES, FT-IR and E M , the degree of SiO, formation at the interface between Si and TazO, was larger in the order of FA-$O_{2}$ > RTA-$O_{2}$, FA-$N_{2}$ > RTA-$N_{2}$. However, the $N_{2}$ ambient annealing resulted in more severe Weficiency in the $Ta_2O_5$ thin film than the TEX>$O_{2}$ ambient.
Over the last decade, the hafnium-based gate dielectric materials have been studied for many application fields. Because these materials had excellent behaviors for suppressing the quantum-mechanical tunneling through the thinner dielectric layer with higher dielectric constant (high-K) than $SiO_2$ gate oxides. Although high-K materials compensated the deterioration of electrical properties for decreasing the thickness of dielectric layer in MOSFET structure, their nano-mechanical properties of $HfO_2$ thin film features were hardly known. Thus, we examined nano-mechanical properties of the Hafnium oxide ($HfO_2$) thin film in order to optimize the gate dielectric layer. The $HfO_2$ thin films were deposited by rf magnetron sputter using hafnium (99.99%) target according to various oxygen gas flows. After deposition, the $HfO_2$ thin films were annealed after annealing at $400^{\circ}C$, $600^{\circ}C$ and $800^{\circ}C$ for 20 min in nitrogen ambient. From the results, the current density of $HfO_2$ thin film for 8 sccm oxygen gas flow became better performance with increasing annealing temperature. The nano-indenter and Weibull distribution were measured by a quantitative calculation of the thin film stress. The $HfO_2$ thin film after annealing at $400^{\circ}C$ had tensile stress. However, the $HfO_2$ thin film with increasing the annealing temperature up to $800^{\circ}C$ had changed compressive stress. This could be due to the nanocrystal of the $HfO_2$ thin film. In particular, the $HfO_2$ thin film after annealing at $400^{\circ}C$ had lower tensile stress, such as 5.35 GPa for the oxygen gas flow of 4 sccm and 5.54 GPa for the oxygen gas flow of 8 sccm. While the $HfO_2$ thin film after annealing at $800^{\circ}C$ had increased the stress value, such as 9.09 GPa for the oxygen gas flow of 4 sccm and 8.17 GPa for the oxygen gas flow of 8 sccm. From these results, the temperature dependence of stress state of $HfO_2$ thin films were understood.
Pot experiments were conducted from 1999 to 2001 to compare the different methods of available phosphorus (P) for estimation of biomass and P uptake by tomato and cucumber grown on different soils (25 soils for tomato and 8 soils for cucumber cultivation) collected from plastic film house of Chungbuk area. Supplementary experiment was conducted to estimate the relationship among several extraction methods of available P such as P adsorption, water extractable-P, Lancaster-P, Olsen-P, Bray No 1 and No 2-P, and Mehlich 1 and 3-P for a total of 71 soils that included 33 soils collected for tomato and cucumber cultivation and 38 soils taken from other sites of plastic film house. All the extraction methods of available phosphorus except P adsorption were mutually positive correlated with r ranging from 0.81 to 0.96 while the correlation coefficient between P adsorption and other methods ranged from -0.57 to -0.80. Phosphorus uptake by tomato plant applied with no fertilizer was significantly correlated with the available P extracted by different methods except P adsorption in all the experiments showing positive correlation coefficients from 0.49 to 0.76 in April, 1999, 0.53 to 0.71 in April, 2000, and 0.59 to 0.68 in October, 2000. Consequently relative amount of P uptake by tomato plant for all the experiments also significantly correlated with available P in soils showing correlation coefficients of r=0.64~0.73 (P<0.0000001) in the order of Mehlich 1-P > Mehlich 3-P > Lancaster-P. For tomato, critical concentrations of available P in soils estimated by Cate and Nelson split method were $1700mg\;kg^{-1}$ for Mehlich 3-P, $1,050mg\;kg^{-1}$ for Mehlich 1-P, and $95mg\;kg^{-1}$ for water extractable P. Also P uptake by cucumber plant was significantly correlated with Olsen-P, water extractable P, and Bray No 2-P with r value of 0.62, 0.59, and 0.51, respectively, in soils of no fertilization.
This study was conducted to estimate the greenhouse gas emissions on local government levels from 1990 to 2010 using 2006 IPCC guideline methodology. To calculate greenhouse gas emissions based on the 16 local governments, emission factor and scaling factor were used with default value and activity data came from the food, agricultural, forestry and fisheries statistical yearbook of MIFAFF (Ministry for Food, Agriculture, Forestry, and Fisheries). The total emissions in crop sector gradually decreased from 1990 to 2010 due to a decline in agricultural land and nitrogen fertilizer usage. The annual average emission of greenhouse gas was the highest in Jeonnam (JN) with 1,698 Gg $CO_2$-eq and following Chungnam (CN), Gyungbuk (GB), Jeonbuk (JB) and Gyunggi (GG). The sum of top-six locals emission had occupied 83.4% of the total emission in cropland sector. The annual average emissions in 1990 by applying 2006 IPCC guideline were approximately 43% less than the national greenhouse gas inventory by 1996 IPCC guideline. Jeonnam (JN) province occupied also the highest results of greenhouse gas emission estimated by gas types (methane, nitrous oxide and carbon dioxide) and emission sources such as rice cultivation, agricultural soil, field burning of crop residue and urea fertilizer.
Kim, Hee Jung;Kim, Mi-Hyun;Jang, Mi;Lim, Tae-Gyu;Hong, Hee-Do;Rhee, Young Kyoung;Kim, Kyung-Tack;Cho, Chang-Won
Food Science and Preservation
/
v.23
no.4
/
pp.502-509
/
2016
The seasonal appearance and the chemical composition characteristics of cladode of Opuntia humifusa were investigated in this study. The minor (horizontal) and major (vertical) axes, the width, and weight of O. humifusa cladode were compared for its appearance features. Moisture, crude protein, ash, fat, color, dietary fiber, mineral, and amino acids contents were measured for the comparison of their chemical composition characteristics. The cladode of O. humifusa harvested in summer showed higher values of minor and major axis, width, and weight than those harvested in winter. According to the results of Hunter color index, cladode of O. humifusa harvested in summer showed the highest lightness level (Hunter L value). In the meanwhile, cladode of O. humifusa harvested in spring showed the highest Hunter a (redness) and b (yellowness) values. Cladode of O. humifusa harvested in summer had the lowest crude protein and crude fat contents, while it showed the highest crude ash content. The total contents of moisture and dietary fiber were significantly greater than summer-harvested cladode of O. humifusa followed by spring- and winter-harvested cladode of O. humifusa. The major mineral content of all seasonal cladode of O. humifusa was $Ca^{2+}$. Glutamic acid and aspartic acid were the major amino acids in all seasonal samples. Contrary, the contents of total amino acids and free amino acids were the lowest in summer-harvested cladode of O. humifusa. Taken together, it was concluded that the appearance and chemical quality of cladode of O. humifusa was versatile depending on the harvesting season.
Jo, Deokjo;Yoo, Seong-Yeol;Park, Joo-Hyeon;Gao, Yaping;Kim, Seul-Gi;Lee, Jea-Young;Kwon, Eun-Jin;Kwon, Joong-Ho
Food Science and Preservation
/
v.21
no.3
/
pp.365-372
/
2014
Imported Valencia oranges were evaluated to determine the relationship between the fruit size and its quality. The orange size was classified into three groups on a commercial basis: small ($140{\sim}160g/113{\pm}5$ fruit/box), medium ($190{\sim}220g/88{\pm}5$ fruit/box), and large ($250{\sim}280g/72{\pm}5$ fruit/box). The physicochemical and sensory properties were analyzed to evaluate the orange quality. No significant difference in the peel thickness and flesh ratio was detected across the fruit sizes. The juice yield of the medium-sized orange and the TSS/TA ratios of the medium-sized and large oranges showed the highest value, respectively (p<0.05). The large orange had the highest vitamin C content, which was positively correlated with both its DPPH and ABTS radical scavenging abilities (p<0.05). In the sensory evaluation of the fruits and their juice, the scores for sourness and overall preference were significantly higher in the medium-sized and large oranges than in the small ones. The total soluble solids, total acidity, TSS/TA ratio, and reducing sugar content were significantly related to the sensory properties. Finally, the quality and sensory properties were considered superior in the medium-sized and lager Valencia oranges. Further studies on the effects of the variety and origin of Valencia oranges on their quality and sensory properties are required.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.