• Proceedings of the KIPE Conference
• /
• 2003.11a
• /
• pp.104-108
• /
• 2003

This paper explained algorithm for a initial pole position estimation of a permanent magnet linear synchronous motor(PMLSM). Generally this motor is considered initial pole position with a position sensor such as incremental encoder for the precise initial pole position estimation and high performance. But this is based on the principle that the initial pole position is accomplished by the PI controller using the maximum values of a position error generated by the new proposed two reference frames and also by using a rated force for input. the proposed algorithm does not utilize the general methods such as impedance ratio, EMF and using the magnetic saturation. In other words, this can be applied without respect to variety of the motor structure because of insensitivity to the motor parameters. In conclusion, simulation results are presented to confirm performance of initial pole position estimation method.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.480-481
• /
• 2015

General microstrip patch antenna has small bandwidth. If corner of a patch antenna is properly cutted to be triangular shape, then input impedance of patch antenna should be varied. Using this characteristic wideband patch antenna can be implemented. In this paper, wideband microstrip patch antenna operating in 2.4GHz ISM band is investigated through tracking variation of input impedance corresponding to cutting shape of patch antenna.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2002.04a
• /
• pp.470-477
• /
• 2002

Possibility of passive piezoelectric damping based on a new shunting parameter estimation method is studied using finite element analysis. The adopted tuning method is based electrical impedance that is found at piezoelectric device and the optimal criterion for maximizing dissipated energy at the shunt circuit. Full three dimensional finite element model is used for piezoelectric devices with cantilever plate structure and shunt electronic circuit is taken into account in the model. Electrical impedance is calculated at the piezoelectric device, which represents the structural behavior in terms of electrical field, and equivalent electrical circuit parameters for the first mode are extracted using PRAP (Piezoelectric Resonance Analysis Program). After the shunt circuit is connected to the equivalent circuit for the first mode, the shunt parameters are optimally decided based on the maximizing dissipated energy criterion. Since this tuning method is based on electrical impedance calculated at piezoelectric device, multi-mode passive piezoelectric damping can be implemented for arbitrary shaped structures.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.1
• /
• pp.52-57
• /
• 2006

In this paper, a new 'impedance sensing' method is described. This method overcomes the shortcomings of the impedance sensing method. According to the new method, sensing voltage pulse is applied to the idle phase in the minimum inductance region and the beginning of the increasing inductance region to detect rotor position. The negative torque produced by the sensing voltage pulse can be neglected in the minimum inductance region and the efficiency of SRM is improved. In the minimum inductance region the back electromotive force (EMF) can be neglected. And in the increasing inductance region the EMF opposes the rise of current in the phase, so the position estimation scheme is reliable. Therefore the new 'impedance sensing' method is sufficiently precise even under the high back EMF effect. The adjustment of turn-on angle and turn-off angle is also easy to be realized. The technique is very useful in applications where cost or size is primary concerns, such as electric bicycle drives. Experimental results are presented to verify the proposed method.

• International Journal of Contents
• /
• v.1 no.1
• /
• pp.1-5
• /
• 2005

This paper presents the development and application of electrical resistance imaging techniques for the visualization of two-phase flow fields. Two algorithms, the so-called the mesh grouping and the boundary estimation, are described for potential applications of electrical resistance tomography (ERT) and results from extensive numerical simulations are also presented. In the electrical resistance imaging for two-phase flows, numerical meshes fairly belonging to each phase can be grouped to improve the reconstruction performance. In many cases, the detection of phase boundary is a key subject and a mathematical model to estimate phase boundary can be formulated in a different manner. Our results indicated that the mesh grouping algorithm is effective to enhance computational performance and image quality, and boundary estimation algorithm to determine the phase boundary directly.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.6
• /
• pp.457-465
• /
• 2009

Lithium batteries are widely used in mobile electronic devices due to their higher voltage and energy density, lighter weight and longer life cycle compared to other secondary batteries. In particular, high demand for lithium batteries is expected for electric cars. In case of lithium batteries used in electric cars, driving distance must be calculated accurately and discharging should not be done below the level of making it impossible to crank. Therefore, accurate information about state of charge (SOC) becomes an essential element for reliable driving. In this paper, a new method of estimating the SOC of lithium polymer batteries by using AC impedance is proposed. In the proposed method, parameters are extracted by fitting a curve of impedance measured at each frequency on the equivalent impedance model and extracted parameters are used to estimate SOC. Experiments were conducted on lithium polymer batteries with similar capacities made by different manufacturers to prove the validity of the proposed method.

• Korean Journal of Acupuncture
• /
• v.29 no.1
• /
• pp.71-81
• /
• 2012

Objectives : The purpose of this paper was to suggest new diagnostic method that was to supersede the estimation of electrical properties at acupoints. Thus, we developed the multi- frequencies bioelectrical impedance measurement system so as to analyze the state of bio-ions in body fluid as body compositions, not skin impedance at acupoint. Methods : At low frequency, the current does not penetrate the cell membrane and at high frequency, the current passes through both intracellular and extracellular fluid because of the decreas of cell membrane impedance. To confirm the reflection of composition in extracellular fluid or intracellular fluid of segment such as acupoint, the system was developed to detect the acupoint potential between adjacent two points in the area of LU3, LU4 and LU9 using 5,50 and 200KHz. Results : The detected acupoint potential has been decreased according to elevation of frequency. As a result of correlation of left/right identical acupoint, we observed a high correlation of three types of acupoint potential at multi-frequencies. Moreover, we observed the low correlation at 5KHz, and that was a significant factor to be considered as unbalanced relationship of identical acupoints. Conclusions : On the basis of meridian theoretical point of view, we may infer the acupoint's physiological composition using the multi-frequencies bioelectrical impedance measurement system.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.3
• /
• pp.136-140
• /
• 2017

The state of charge (SOC) is an important parameter in a battery-management system (BMS), and is very significant for accurately estimating the SOC of a battery. Li-ion batteries boast of excellent performance, and can only remain at their best working state by means of accurate SOC estimation that gives full play to their performances and raises their economic benefits. This paper summarizes some measures taken in SOC estimation, including the discharge experiment method, the ampere-hour integral method, the open circuit voltage method, the Kalman filter method, the neural network method, and electrochemical impedance spectroscopy (EIS. The principles of the various SOC estimation methods are introduced, and their advantages and disadvantages, as well as the working conditions adopted during these methods, are discussed and analyzed.

• Journal of the Semiconductor & Display Technology
• /
• v.7 no.2
• /
• pp.13-17
• /
• 2008

In this paper, in order to get the characteristics of the lithium secondary cell, such as charge and discharge characteristic, temperature characteristic, self-discharge characteristic and the capacity recovery rate etc, we build a thermal model that estimate the impedance of battery by experiment & simulation. In this one-dimensional model, Seven governing equations are made to solve seven variables c, $c_s,\;\Phi_1,\;\Phi_2,\;i_2$, j and T. The thermal model parameters used in this model have been adjusted according to the experimental data measured in the laboratory. The result(Voc, Impedance) of this research can be used in BMS(Battery Management System), so an efficient method of using battery is developed.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.6
• /
• pp.622-634
• /
• 2003

This paper is concerned with a computational method for recovering a crack shape of steam generator tubes of nuclear plants. Problems on the shape identification are discussed arising in the characterization of a structural defect in a conductor using data of eddy current inspection. A surface defect on the generator tube ran be detected as a probe impedance trajectory by scanning a pancake type coil. First, a mathematical model of the inspection process is derived from the Maxwell's equation. Second, the input and output relation is given by the approximate model by virtue of the hybrid use of the finite element and boundary element method. In that model, the crack shape is characterized by the unknown coefficients of the B-spline function which approximates the crack shape geometry. Finally, a parameter estimation technique is proposed for recovering the crack shape using data from the probe coil. The computational experiments were successfully tested with the laboratory data.