• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.592-595
• /
• 2004

This paper presents a study on the development of a multi-sensing inertial sensor with a single mechanical structure, which can be used both as a gyroscope and an accelerometer. The proposed MEMS gyro-accelerometer is designed to detect the angular rate and the acceleration at the same time using two separate detection circuits for one proof mass. In this study, the detection and signal processing circuit for an effective signal processing of different inertial measurements is designed, fabricated, and tested. The experimental results show that the performances of the gyro-accelerometer have resolutions of 1mg and 0.025deg/sec and nonlinearities of less than 0.5% for the accelerometer and the gyroscope, respectively, which are similar results with those of sensors with different structures and different detection circuits. The size of the sensor is reduced almost by 50% comparing with the sensors of separated proof mass.

• 비파괴검사학회지
• /
• 제27권6호
• /
• pp.556-562
• /
• 2007

This paper presents the use of a novel fiber optic accelerometer system to monitor ambient vibration (both wind-induced one and vehicle-induced) of a real bridge structure. This sensor system integrates the $Moir\'{e}$ fringe phenomenon with fiber optics to achieve accurate and reliable measurements. A low-cost signal processing unit implements unique algorithms to further enhance the resolution and increase the dynamic bandwidth of the sensors. The fiber optic accelerometer has two major benefits in using this fiber optic accelerometer system for monitoring civil engineering structures. One is its immunity to electromagnetic (EM) interference making it suitable for difficult applications in such environments involving strong EM fields, electrical spark-induced explosion risks, and cabling problems, prohibiting the use of conventional electromagnetic accelerometers. The other is its ability to measure both low- and high-amplitude vibrations with a constantly high resolution without pre-setting a gain level, as usually required in a conventional accelerometer. The second benefit makes the sensor system particularly useful for real-time measurement of both ambient vibration (that is often used for structural health monitoring) and strong motion such as earthquake. Especially, the semi-strong motion and the small ambient one are successfully simulated and measured by using the new fiber optic accelerometer in the experiment of the structural health monitoring of a real bridge.

• 전기학회논문지
• /
• 제58권11호
• /
• pp.2275-2280
• /
• 2009

u-Healthcare service is one of attractive applications in ubiquitous environment. In this paper, we propose a method to recognize exercises using a new accelerometer based body-attached platform for supporting u-Healthcare service. The platform consists of a device for measuring accelerometer data and a device for receiving the data. The former measures a user's motion data using a 3-axis accelerometer. The latter transmits the accelerometer data to a computer for recognizing the user's exercise. The algorithm for exercise recognition classifies the type of exercise using principle components analysis(PCA) from the accelerometer data transformed by discrete fourier transform(DFT), and estimates the repetition count of the recognized exercise using a peak detection algorithm. We evaluate the performance of the algorithm from the accuracy of the recognition of exercise type and the error rate of the estimation of repetition count. In our experimental result, the algorithm shows the accuracy about 98%.

• Smart Structures and Systems
• /
• 제5권4호
• /
• pp.345-355
• /
• 2009

This article describes the development of a fiber optic accelerometer based on Fiber Bragg Gratings (FBG). The accelerometer utilizes the stiffness of the optical fiber and a lumped mass in the design. Acceleration is measured by the FBG in response to the vibration of the fiber optic mass system. The wavelength shift of FBG is proportional to the change in acceleration, and the gauge factor pertains to the shift in wavelength as a function of acceleration. Low frequency version of the accelerometer was developed for applications in monitoring bridges. The accelerometer was first evaluated in laboratory settings and then employed in a demonstration project for condition assessment of a bridge. Laboratory experiments involved evaluation of the sensitivity and resolution of measurements under a series of low frequency low amplitude conditions. The main feature of this accelerometer is single channel multiplexing capability rendering the system highly practical for application in condition assessment of bridges. This feature of the accelerometer was evaluated by using the system during ambient vibration tests of a bridge. The Frequency Domain Decomposition method was employed to identify the mode shapes and natural frequencies of the bridge. Results were compared with the data acquired from the conventional accelerometers.

• 한국군사과학기술학회지
• /
• 제24권6호
• /
• pp.577-590
• /
• 2021

In this paper, we theoretically analyzed the self-alignment/navigation performance in the accelerometer resonance state generated by dither motion of ring laser gyroscope in LINS and verified it through simulation. As a result of analysis, it is confirmed that the amplitude of the accelerometer measurement amplified in the accelerometer resonance state is decreased in the process of sampling per the navigation calculation period and that frequency is changed by the aliasing effect too. It was also analysed that the attitude error in self-alignment is determined by the amplitude/frequency of the accelerometer measurement, the gain of the self-alignment loop, and the velocity and position error in the navigation is determined by the amplitude/frequency/phase error of the accelerometer measurement. This analysis and simulation results show that the self-alignment and navigation performance is not be degraded only when the amplification factor of the accelerometer measurement in the accelerometer resonance state is 3 or less

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.848-851
• /
• 2002

In this paper, an experimental method using a reference accelerometer has been developed to measure the in-plane vibration intensity of a beam. It has the advantages of reducing accelerometer phase error comparing with the cross spectral intensity measurement technique using an accelerometer array. It needs no measurement of the input force required in the frequency response method using the only one accelerometer This method has been used to measure the in-plane vibration intensity over the beam. The result has been compared with an input power and the vibration intensity obtained with other methods. It showed that the present experimental method can be effectively used to measure the structural in-plane vibration intensity.

• Smart Structures and Systems
• /
• 제13권6호
• /
• pp.959-974
• /
• 2014

Hand-Arm Vibration Syndrome (HAVS) is a group of diseases caused by exposure of the hands to vibration while operating the hand held power tools such as road breaker, drilling machine, demolition hammer in construction works. In this paper, area-changed capacitive micro-accelerometer is designed to measure the vibration exposure on worker's hand when operating a drilling machine on various blocks such as clay block, paver block and solid cement block. The design process includes mathematical modelling of micro-accelerometer and simulations are done using INTELLISUITE 8.6. Experimental results are taken for various blocks surfaces using conventional and micro-accelerometer. Comparisons show that usage of area-changed micro-accelerometer for Hand-arm vibration monitoring provides better sensitivity, which in turn reduces the risk of HAVS in workers.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 학술대회 논문집 정보 및 제어부문
• /
• pp.542-544
• /
• 2005

This paper describes the detection of spatio-temporal parameter using an accelerometer and footswitches to evaluate a symmetry and balance of hemiplegic patients. We detected gait data using a 3-axis accelerometer that mounted between L3 and IA intervertebral area and footswitches made by FSR-Sensor attached insole. To minimize the error of the gait parameters to be detected incorrectly in case of using only accelerometer, we enhancement the performance of detection by measuring an accelerometer and foots witches data at the same time. So, it was possible to detect more accurate gait parameters. As a result, we can confirm the symmetry and balance of hemiplegic patients. In the future. these results could be used to evaluate the walking ability in hemiplegic patients in clinical pratice.

• The Journal of Korean Physical Therapy
• /
• 제22권6호
• /
• pp.59-63
• /
• 2010

Purpose: Driving a car is an essential component of daily life. For safe driving, each driver must perceive sensory information and respond rapidly and accurately. Brake response time (BRT) is a particularly important factor in the total stopping distance of a vehicle, and therefore is an important factor in traffic accident prevention research. The purpose of the current study was (1) to compare accelerometer. BRTs analyzed by three different methods and (2) to investigate possible correlations between accelerometer-BRTs and foot switch-BRTs, which are measured method using a foot switch. Methods: Eighteen healthy subjects participated in this study. BRT was measured with either a tri-axial accelerometer or a footswitch. BRT with a tri-axial accelerometer was analyzed using three methods: maximum acceleration time, geometrical center, and center of maximum and minimum acceleration values. Results: Both foot switch-BRTs and accelerometer-BRTs were delayed. ANOVA for accelerometer BRTs yielded significant main effects for axis and analysis, while the interaction effect between axis and analysis was not significant. Calculating the Pearson correlation between accelerometer-BRT and foot switch-BRT, we found that maximum acceleration time and center of maximum and minimum acceleration values were significantly correlated with foot switch-BRT (p<0.05). The X axis of the geometrical center was significantly correlated with foot switch-BRTs (p<0.05), but Y and Z axes were not (p>0.05). Conclusion: These findings suggest that the maximum acceleration time and the center of maximum and minimum acceleration value are significantly correlated with foot switch-BRTs.

• 비파괴검사학회지
• /
• 제27권4호
• /
• pp.291-298
• /
• 2007

본 논문은 단자유도 동적 센서 시스템의 동적 구간을 조절할 수 있는 새로운 신호 처리법을 소개한다. 또한 본 논문에서는 무아래 현상을 응용한 신개념의 광섬유 가속도계를 사용하여 신호 처리법을 검증하였다. 신개념의 광섬유 가속도계는 단일 질량, 단일 탄성자 그리고 단일 감쇠자로 이루어진 단자유도 동적 시스템으로서 동적 구간이 작아 이출 증가시키기 위해서는 질량이나 탄성자 상수를 조절하는 등의 기계적 조절이 필요하다. 그러나 본 논문에서 제안한 신호처리 방법을 적용한다면 센서를 다시 제작하지 않고도 동적 구간을 쉽게 조절할 수 있게 된다. 본 논문에서는 여러 모의실험과 실제 실험을 통해 본 신호 처리 알고리즘의 성능을 검증하였으며 결과적으로 이러한 신호처리 알고리즘이 광섬유 가속도계의 동적 구간을 손쉽게 조절할 수 있는 효과적인 방법임을 보여주었다.