• Korean Journal of Materials Research
• /
• v.30 no.11
• /
• pp.615-620
• /
• 2020

Oxide semiconductor, represented by a-IGZO, has been commercialized in the market as active layer of TFTs of display backplanes due to its various advantages over a-Si. a-IGZO can be deposited at room temperature by RF magnetron sputtering process; however, additional thermal annealing above 300℃ is required to obtain good semiconducting properties and stability. These temperature are too high for common flexible substrates like PET, PEN, and PI. In this work, effects of microwave annealing time on IGZO thin film and associated thin-film transistors are demonstrated. As the microwave annealing time increases, the electrical properties of a-IGZO TFT improve to a degree similar to that during thermal annealing. Optimal microwave annealed IGZO TFT exhibits mobility, SS, V_th, and V_H of 6.45 ㎠/Vs, 0.17 V/dec, 1.53 V, and 0.47 V, respectively. PBS and NBS stability tests confirm that microwave annealing can effectively improve the interface between the dielectric and the active layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05c
• /
• pp.108-111
• /
• 2002

CIGS film has been fabricated on soda-lime glass, which is coated with Mo film. by multi-source evaporation process. The films has been prepared with thickness of 1.0 ${\mu}m$, 1.75${\mu}m$, 2.0${\mu}m$, 2.3${\mu}m$, and 3.0${\mu}m$. X-ray diffraction analysis with film thickness shows that CIGS films exhibit a strong (112) preferred orientation. Furthermore. CIGS films exhibited distinctly decreasing the full width of half-maximum and (112) preferred peak with film thickness. Also, The film's microstructure, such as the preferred orientation, the full width at half-maximum(FWHM), and the interplanar spacing were examined by X-ray diffraction. The preparation condition and the characteristics of the unit layers were as followings ; Mo back contact DC sputter, CIGS absorber layer : three-stage coevaporation, CdS buffer layer : chemical bath deposition, ZnO window layer : RF sputtering, $MgF_2$ antireflectance : E-gun evaporation

• Korean Journal of Metals and Materials
• /
• v.48 no.6
• /
• pp.565-569
• /
• 2010

We report on the characteristics of indium-oxide-doped ZnO (IZO) ohmic contact to p-GaN. The IZO ohmic contact layer was deposited on p-GaN by a Roll-to-Roll (RTR) sputter method. IZO contact film with a thickness of 360, 230 and 100 nm yielded an ohmic contact resistance of $4.70{\times}10^{-4}$, $5.95{\times}10^{-2}$, $4.85{\times}10^{-1}\;{\Omega}cm^{2}$ on p-GaN when annealed at $600{^{\circ}C}$ for 1 min under a nitrogen ambient, respectively. While the transmittance of IZO film with a thickness of 360 nm slightly increased in the wavelength range of 380-800 nm after annealing, the transmittance rapidly increased up to 80% after annealing at $600{^{\circ}C}$ in the wavelength range of 380~430 nm because the crystallization of IZO film and created Ga vacancies near the p-GaN surface region were affected by the annealing. These results indicate that ohmic contact resistance and transmittance of the IZO films improved.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.287.1-287.1
• /
• 2016

Three-dimensional (3-D) semiconductor nanoarchitectures, including nano- and micro- rods, pyramids, and disks, are emerging as one of the most promising elements for future optoelectronic devices. Since these 3-D semiconductor nanoarchitectures have many interesting unconventional properties, including the use of large light-emitting surface area and semipolar/nonpolar nano- or micro-facets, numerous studies reported on novel device applications of these 3-D nanoarchitectures. In particular, 3-D nanoarchitecture devices can have noticeably different current spreading characteristics compared with conventional thin film devices, due to their elaborate 3-D geometry. Utilizing this feature in a highly controlled manner, color-tunable light-emitting diodes (LEDs) were demonstrated by controlling the spatial distribution of current density over the multifaceted GaN LEDs. Meanwhile, for the fabrication of high brightness, single color emitting LEDs or laser diodes, uniform and high density of electrical current must be injected into the entire active layers of the nanoarchitecture devices. Here, we report on a new device structure to inject uniform and high density of electrical current through the 3-D semiconductor nanoarchitecture LEDs using metal core inside microtube LEDs. In this work, we report the fabrications and characteristics of metal-cored coaxial $GaN/In_xGa_{1-x}N$ microtube LEDs. For the fabrication of metal-cored microtube LEDs, $GaN/In_xGa_{1-x}N/ZnO$ coaxial microtube LED arrays grown on an n-GaN/c-Al2O3 substrate were lifted-off from the substrate by wet chemical etching of sacrificial ZnO microtubes and $SiO_2$ layer. The chemically lifted-off layer of LEDs were then stamped upside down on another supporting substrates. Subsequently, Ti/Au and indium tin oxide were deposited on the inner shells of microtubes, forming n-type electrodes of the metal-cored LEDs. The device characteristics were investigated measuring electroluminescence and current-voltage characteristic curves and analyzed by computational modeling of current spreading characteristics.

• Journal of the Korean Ceramic Society
• /
• v.39 no.10
• /
• pp.935-942
• /
• 2002

Gallium-doped ZnO (GZO) films were deposited on soda-lime glass substrate without heating using Ne, Ar, or Kr gas. Electrical properties of GZO films deposited at various total gas pressures were investigated for the film positions corresponding to the erosion region (region B) and outside the erosion region (region A) of the target. Region B showed high resistivity, which was attributed to the decrease in carrier density and Hall mobility, compared to region A. GZO films deposited using Ne gas showed the degradation in resistivity and crystallinity, whereas, GZO films deposited using Kr gas showed the improvement in resistivity and crystallinity. This degradation in film properties could be attributed to the film damage caused by the bombardment of high-energy particles. Especially, the energies of recoiled neutral atoms ($Ne^0,\;Ar^0,\;Kr^0$) calculated by Monte Carlo simulation corresponded to experimental results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.10
• /
• pp.648-652
• /
• 2014

We have investigated the effect of electrical properties of amorphous InGaZnO thin film transistors (a-IGZO TFTs) by post thermal annealing in $O_2$ ambient. The post-annealed in $O_2$ ambient a-IGZOTFT is found to be more stable to be used for oxide-based TFT devices, and has better performance, such as the on/off current ratios, sub-threshold voltage gate swing, and, as well as reasonable threshold voltage, than others do. The interface trap density is controlled to achieve the optimum value of TFT transfer and output characteristics. The device performance is significantly affected by adjusting the annealing condition. This effect is closely related with the modulation annealing method by reducing the localized trapping carriers and defect centers at the interface or in the channel layer.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.18 no.5
• /
• pp.797-802
• /
• 2023

We prepared GZO (Ga₂O₃ : 5 wt %, ZnO : 95 wt %) thin film on glass substrate according to the substrate temperature using the pulsed laser deposition method and investigated electrical and optical properties of the thin film. Through the XRD measurements, their were confirmed that all GZO thin films grew preferentially in c-axis and the GZO thin film deposited at 300℃ showed the best crystallinity with a FWHM of 0.38°. As the substrate temperature increased from 150 to 300℃, the resistivity of GZO thin film tend to decrease, while the average transmittance in the visible light region was not significantly affected. The figure of merit of the GZO thin film deposited at 300℃ was 2.05×10⁴ Ω^-1·cm^-1, which was the best value, the resistivity and the average transmittance in the visible light region were 3.72 × 10^-4 Ω·cm and 87.71 %, respectively. In this study, it was found that GZO thin film is very promising material for transparent conducting thin film.

• Journal of the Korean Society for Heat Treatment
• /
• v.24 no.3
• /
• pp.140-143
• /
• 2011

In this work, Ga doped ZnO (GZO) films were prepared by radio frequency (RF) magnetron sputtering without intentional substrate heating on glass substrate and then the effect of the intense electron irradiation on structural and electrical properties and the NOx gas sensitivity were investigated. Although as deposited GZO films showed a diffraction peak for ZnO (002) in the XRD pattern, GZO films that electron irradiated at electron energy of 900 eV showed the higher intense diffraction peaks than that of the as deposited GZO films. The electrical property of the films are also influenced with electron's energy. As deposited GZO films showed the three times higher resistivity than that of the films irradiated at 900 eV In addition, the sensitivity for NOx gas is also increased with electron irradiation energy and the film sensor showed the proportionally increased gas sensitivity with NOx concentration. This approach is promising in gaining improvement in the performance of thin film gas sensors used for the detection of hazard gas phase.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1333-1334
• /
• 2007

Al thin film was the most popular electrode in semiconductor and flat panel display world, because of its electrical conductivity, selectivity and easy to apply to thin film. However, Al thin films were not good to use on the bottom electrode about the crystalline growth of inorganic compound materials such as ZnO, AlN and GaN, because of its surface roughness and melting points. In this paper, we investigated Ar plasma surface treatment of Al thin film to enhance the surface roughness and electrical conductivity using the reactive ion etching system. Several process conditions such as RF power, working pressure and process time were controlled. In results, the surface roughness showed $15.53\;{\AA}$ when RF power was 100 W, working pressure was 50 mTorr and process time was 10 min. Also, we tried to deposit ZnO thin films on the each Al thin films, the upper conditions showed the best crystalline characteristics by x-ray diffraction.

• Journal of the Semiconductor & Display Technology
• /
• v.8 no.4
• /
• pp.65-69
• /
• 2009

Carbon nanotubes (CNTs) were coated with undoped zinc oxide (ZnO) or 5 wt% gallium-incorporated ZnO (GZO) using various deposition conditions. The CNTs were directly grown on conical-type tungsten substrates at $700^{\circ}C$ using inductively coupled plasma-chemical vapor deposition. The pulsed laser deposition technique was used to deposit the ZnO and GZO thin films with very low stress. Field-emission scanning electron microscopy and high-resolution transmission electron microscopy were used to monitor the variations in the morphology and microstructure of CNTs prior to and after ZnO or GZO coating. The formation of ZnO and GZO films on CNTs was confirmed using energy-dispersive x-ray spectroscopy. In comparison to the as-grown (uncoated) CNT emitter, the CNT emitter that was coated with a thin (10 nm) GZO film showed remarkably improved field emission characteristics, such as the emission current of $325\;{\mu}A$ at 1 kV and the threshold field of $1.96\;V/{\mu}m$ at $0.1\;{\mu}A$, and it also exhibited the highly stable operation of emission current up to 40 h.