• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.444.1-444.1
• /
• 2014

높은 광흡수 계수를 갖는 Cu(In,Ga)Se2(CIGS) 화합물 박막 소재는 고효율 태양전지 양산을 위해 가장 전도유망한 재료이나 상대적으로 매장량이 적은 In 및 Ga을 사용한다는 소재적 한계가 있다. Cu2ZnSnSe4(CZTSe) 혹은 Cu2ZnSnS4(CZTS)와 같은 Cu-Zn-Sn-Se계 화합물 반도체는 CIGS 내 희소원소인 In과 Ga이 범용원소인 Zn 및 Sn으로 대체된 소재로써 미래형 저가 태양전지 개발을 위해 활발히 연구되고 있는데, 그 화합물 조합에 따라 0.8eV부터 1.5eV까지의 에너지 밴드갭을 갖는 것으로 알려져 있다. 본 연구에서는 열분해법으로 CZTS 나노 입자를 합성하였다. 용매로 Oleylamine을 사용하였는데, $220^{\circ}C{\sim}340^{\circ}C$의 온도 범위에서 3시간 30분 동안 CZTS 나노입자를 합성하였고, $240^{\circ}C$에서 3시간~5시간까지 합성하였다. 헥산을 이용하여 원심분리기와 초음파세척기로 용매인 Oleylamine을 제거하였고, 진공오븐에서 건조된 CZTS 분말의 FE-SEM(Field Emission Scanning Electron Microscope), XRD(X-Ray Diffraction), EDS(Energy Dispersive Spectroscopy) 분석 등을 통해 합성온도에 따른 구조적, 화학적 조성 변화를 조사하였다.

• Korean Journal of Materials Research
• /
• v.30 no.3
• /
• pp.117-122
• /
• 2020

The effects of fast neutron irradiation on the electrical and optical properties of Li (3 at%) doped ZnSnO (ZTO) thin films fabricated using a sol-gel process are investigated. From the results of Li-ZTO TFT characteristics according to change of neutron irradiation time, the saturation mobility is found to increase and threshold voltage values shift to a negative direction from 1,000 s neutron irradiation time. X-ray photoelectron spectroscopy analysis of the O 1s core level shows that the relative area of oxygen vacancies is almost unchanged with different irradiation times. From the results of band alignment, it is confirmed that, due to the increase of electron carrier concentration, the Fermi level (E_F) of the sample irradiated for 1,000 s is located at the position closest to the conduction band minimum. The increase in electron concentration is considered by looking at the shallow band edge state under the conduction band edge formed by fast neutron irradiation of more than 1,000 s.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.321.1-321.1
• /
• 2013

높은 광흡수 계수를 갖는 Cu(In,Ga)Se2(CIGS) 화합물 박막 소재는 고효율 태양전지 양산을 위해 가장 전도유망한 재료이나 상대적으로 매장량이 적은 In 및 Ga을 사용한다는 소재적 한계가 있다. Cu2ZnSnSe4(CZTSe) 혹은 Cu2ZnSnS4(CZTS)와 같은 Cu-Zn-Sn-Se계 화합물 반도체는 CIGS 내 희소원소인 In과 Ga이 범용원소인 Zn 및 Sn으로 대체된 소재로써 미래형 저가 태양전지 개발을 위해 활발히 연구되고 있는데, 그 화합물 조합에 따라 0.8eV부터 1.5eV까지의 에너지 밴드갭을 갖는 것으로 알려져 있다. 본 연구에서는 열분해법으로 CZTS 나노 입자를 합성하였다. 용매로 Oleylamine을 사용하였는데, $260{\sim}340^{\circ}C$의 온도 범위에서 5시간 30분 동안 CZTS 나노입자를 합성하였고, $300^{\circ}C$에서 5시간 30분~9시간까지 합성하였다. 헥산을 이용하여 원심분리기와 초음파세척기로 용매인 Oleylamine을 제거하였고, 진공오븐에서 건조된 CZTS 분말의 FE-SEM (Field Emission Scanning Electron Microscope), XRD (X-Ray Diffraction), EDS (Energy Dispersive Spectroscopy) 분석 등을 통해 합성온도에 따른 구조적, 화학적 조성 변화를 조사하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.688-688
• /
• 2013

Al-doped ZnO (AZO) thin films have attracted a lot of attention as a cheap transparent conducting oxide (TCO) material that can replace the expensive Sn-doped In2O3. In particular, AZO thin films are widely used as a window layer of chalcogenide-based thin film solar cells such as Cu(In,Ga)Se2 and Cu2ZnSnS4 (CZTS). Mostly important requirements for the window layer material of the thin film solar cells are the high transparency and the low sheet resistance, because they influence the light absorption by the activelayer and the electron collection from the active layer, respectively. In this study, we prepared the AZO thin films by RF magnetron sputtering using a ZnO/Al2O3 (98：2wt%) ceramic target, and the effect of the sputtering condition such as the working pressure, RF power, and the working distance on the optical, electrical, and crystallographic properties of the AZO thin films was investigated. The AZO thin films with optimized properties were used as a window layer of CZTS thin film solar cells. The CZTS active layers were prepared by the electrochemical deposition and the subsequent sulfurization process, which is also one of the cost-effective synthetic approaches. In addition, the solar cell properties of the CZTS thin film solar cells, such as the photocurrent density-voltage (J-V) characteristics and the external quantum efficiency (EQE) were investigated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.303-305
• /
• 1996

The electrical Properties of ZnO added TiO$_2$were investigated by using the complex impedance measurement and voltage-current source and measurement unit. The electrical conductivity of ZnO added TiO$_2$decrease with increasing the content of ZnO. The frequency-dependent Ac conductivity increase as frequency increase. Also, the trend of capacitances is similar to the AC conductivity. The semicircles of impedance spectrum increase with increasing ZnO contents. The decrease of electrical conductivity seems to be the effect of ZnO acceptor adding.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.12 no.4
• /
• pp.35-40
• /
• 1975

The Zn7e-lnSb heterojunctions was prepared by interface alloying technique. The structure of this beterojunction had p-i-n which semi-insulating ZnTe laver at interface of this heterojunction was formed by diffusing In of InSb into ZnTe crystal. The current transport mechanism of this heterojunction was Spacecharge-Limited-Current(SCLC) mechanism by hole at semi-insulating ZnTe layer. The hole wart injected from valence band of p- type SnTe crystal. Orange color electroluminescence was observed at this heterojunction when forward and reversed bias voltage applied.

• Journal of Sensor Science and Technology
• /
• v.6 no.6
• /
• pp.451-457
• /
• 1997

The thick films of oxide semiconductors such as $WO_{3}$, $SnO_{2}$ and ZnO for the $NO_{2}$ detection of sub-ppm range have been prepared and their characteristics were investigated. It is showed that the optimum operating temperatures of the sensors are $300^{\circ}C$ and $220{\sim}260^{\circ}C$ for $WO_{3}$-based and $SnO_{2}$-based thick films, and ZnO-based thick films, respectively. Since the resistance of ZnO-based thick films are extremely high($>10^{6}{\Omega}$), the signal to noise ratio was comparatively low. In order to determine the selectivity, the films are exposed to the interfering gases such as ozone, ammonia, methane and the mixture of carbon monoxide and propane. $WO_{3}$-ZnO(3 wt.%) and $SnO_{2}-WO_{3}$(3 wt.%) thick film sensors show high sensitivity, good selectivity, excellent reproducibility and the linearity of $NO_{2}$ concentration versus sensor resistance. The preliminary results clearly demonstrated that the sensor can be successfully applied for the detection of $NO_{2}$ in sub-ppm range.

• Journal of IKEEE
• /
• v.13 no.4
• /
• pp.37-42
• /
• 2009

In this study, nanopower ZnO and $SnO_2$ as sensing materials were prepared by hydrazine and hydrothermal routes, respectively, and were doped with Pd, Ru catalyst. The CO and $NO_2$ sensors were fabricated by coating of sensing materials on the MEMS-based structure with electrodes and heaters. The 0.1 wt% Pd doped $SnO_2$ sensor and Ru doped ZnO sensor showed the high sensor response to CO 30 ppm and $NO_2$ 1 ppm, respectively. The sensor signal was stable. This can be used for the detection of pollutant gases emitted from gasoline engine.

• Current Photovoltaic Research
• /
• v.2 no.4
• /
• pp.177-181
• /
• 2014

$Cu_2ZnSn(S_xSe_{1-x})_4$ (CZTSSe) absorber thin films were prepared on Mo coated soda lime glass substrates by sulfo-selenization of sputtered stacked Zn-Sn-Cu precursor thin films. The Zn-Sn-Cu precursor thin films were sulfo-selenized inside a graphite box containing S and Se powder using rapid thermal processing furnace at $540^{\circ}C$ in Ar atmosphere with pre-treatment at $300^{\circ}C$. The effect of different S/Se ratio on the structural, compositional, morphological and electrical properties of the CZTSSe thin films were studied using XRD (X-ray diffraction), XRF (X-ray fluorescence analysis), FE-SEM (field-emission scanning electron microscopy), respectively. The XRD, FE-SEM, XRF results indicated that the properties of sulfo-selenized CZTSSe thin films were strongly related to the S/Se composition ratio. In particular, the CZTS thin film solar cells with S/(S+Se)=0.25 shows best conversion efficiency of 4.6% ($V_{oc}$ : 348 mV, $J_{sc}$ : $26.71mA/cm^2$, FF : 50%, and active area : $0.31cm^2$). Further detailed analysis and discussion for effect of S/Se composition ratio on the properties CZTSSe thin films will be discussed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.304.1-304.1
• /
• 2014

Flat-panel displays have been growing as an essential everyday product in the current information/communication ages in the unprecedented speed. The forward-coming applications require light-weightness, higher speed, higher resolution, and lower power consumption, along with the relevant cost. Such specifications demand for a new concept-based materials and applications, unlike Si-based technologies, such as amorphous Si and polycrystalline Si thin film transistors. Since the introduction of the first concept on the oxide-based thin film transistors by Hosono et al., amorphous oxide thin film transistors have been gaining academic/industrial interest, owing to the facile synthesis and reproducible processing despite of a couple of shortcomings. The current work places its main emphasis on the binary oxides composed of ZnO and SnO2. RF sputtering was applied to the fabrication of amorphous oxide thin film devices, in the form of bottom-gated structures involving highly-doped Si wafers as gate materials and thermal oxide (SiO2) as gate dielectrics. The physical/chemical features were characterized using atomic force microscopy for surface morphology, spectroscopic ellipsometry for optical parameters, X-ray diffraction for crystallinity, and X-ray photoelectron spectroscopy for identification of chemical states. The combined characterizations on Zn-Sn-O thin films are discussed in comparison with the device performance based on thin film transistors involving Zn-Sn-O thin films as channel materials, with the aim to optimizing high-performance thin film transistors.