• 한국재료학회지
• /
• 제20권5호
• /
• pp.235-240
• /
• 2010

We investigated the carbon monoxide (CO) gas-sensing properties of nanostructured Al-doped zinc oxide thin films deposited on self-assembled Au nanodots (ZnO/Au thin films). The Al-doped ZnO thin film was deposited onto the structure by rf sputtering, resulting in a gas-sensing element comprising a ZnO-based active layer with an embedded Pt/Ti electrode covered by the self-assembled Au nanodots. Prior to the growth of the active ZnO layer, the Au nanodots were formed via annealing a thin Au layer with a thickness of 2 nm at a moderate temperature of $500^{\circ}C$. It was found that the ZnO/Au nanostructured thin film gas sensors showed a high maximum sensitivity to CO gas at $250^{\circ}C$ and a low CO detection limit of 5 ppm in dry air. Furthermore, the ZnO/Au thin film CO gas sensors exhibited fast response and recovery behaviors. The observed excellent CO gas-sensing properties of the nanostructured ZnO/Au thin films can be ascribed to the Au nanodots, acting as both a nucleation layer for the formation of the ZnO nanostructure and a catalyst in the CO surface reaction. These results suggest that the ZnO thin films deposited on self-assembled Au nanodots are promising for practical high-performance CO gas sensors.

• 대한금속재료학회지
• /
• 제47권12호
• /
• pp.834-841
• /
• 2009

A study on the welding of electrogalvanized TRIP (Transformation-Induced Plasticity) steels was done to compare the life of the electrode and the alloying phenomena on the electrode tip surface using singlephase AC and inverter-DC resistance welding processes. A longer life of the electrode (>200 welds) was achieved using the inverter-DC welding process. The tensile shear strength was higher in the electrode life test when welded with the inverter DC welding machine it maintained a higher value even when the welding nugget diameter was smaller than specified. When spot-welding was conducted using the single-phase AC welding process, a higher wear rate of the electrode was observed compared to that with the inverter-DC process. An alloying layer used to determine the rate of electrode growth showed differences in the metallurgical features of the surface alloying and Zn penetration depending on whether the single-phase AC process or the inverter-DC welding process was used. Moreover, changes in the dynamic resistance during the electrode life test were correlated with the electrode wear (or growth) rate.

• 한국안전학회지
• /
• 제27권3호
• /
• pp.63-70
• /
• 2012

In the hazardous areas where explosive gases, vapor or mists exist, electrical apparatus and installations must be the explosion-proof construction to prevent or limit the danger of the ignition of potentially explosive atmosphere. In Korea, nine types of protection have been specified in the government regulations at present: flameproof enclosure, pressurization, oil immersion, increased safety, intrinsic safety, non-incendive, powder filling, encapsulation, and special types. Among these types, the intrinsic safety has the construction which limit or by-pass igniting the electric energy using electronic devices. This type has lots of merits but at the same time requires a high-degree of technology. In this paper, we investigated several dominating factors which affect the minimum ignition energy; this energy plays a very important role in design and evaluation of the intrinsic safety type electrical apparatus. Electrode material, which is one of the most important factors, was intensively studied for the five sorts of material(Al, Cd, Mg, Sn, and Zn) with performing experiment in a low-voltage inductive circuit using IEC-type(International Electro-technical Commission) spark apparatus. The experimental results show that the minimum ignition energy of electrode material is varied: highest in Cd and lowest in Sn. We also confirmed the effect of electrode make-and-break speed.

• 한국자기학회지
• /
• 제25권5호
• /
• pp.156-161
• /
• 2015

이 연구에서는 X-선 광전자분광법(X-ray photoemission spectroscopy: XPS)을 이용하여 염료감응 태양전지의 전극용 후보 물질에 속하는 $ZnSnO_3$와 $Zn_2SnO_4$의 전자 구조를 연구하였다. 제조된 시료들에 대한 X-선 회절 측정에 의하면 $ZnSnO_3$와 $Zn_2SnO_4$ 시료는 각각 단일상의 ilmenite(IL) 구조와 역스피넬(inverse spinel) 구조를 가지고 있음을 알 수 있었다. Zn 2p와 Sn 3d 내각준위 XPS 측정으로부터 $ZnSnO_3$와 $Zn_2SnO_4$ 두 시료 모두에서 Zn 이온은 2가 (Zn 2+) 상태이며, Sn 이온은 4가 (Sn 4+) 상태임을 알 수 있었다. 한편 얕은 내각준위 XPS 스펙트럼의 측정에서는 $ZnSnO_3$의 Sn 4d와 Zn 3d 내각 준위들의 결합에너지가 $Zn_2SnO_4$에서 보다 다소 작게 관찰되었다. 이 연구로부터 $ZnSnO_3$와 $Zn_2SnO_4$에서의 각 이온의 원자가 상태와 화학적 결합 상태에 대한 정보를 얻을 수 있었다.

• Journal of Electrochemical Science and Technology
• /
• 제3권4호
• /
• pp.178-184
• /
• 2012

A porous nickel (P-Ni) substrate was prepared by selective leaching of zinc from pressed pellets containing powders of Ni & Zn in 4 M NaOH solution. Anodic deposition of manganese oxide onto the porous Ni substrate ($MnO_x$/P-Ni) formed nano-flakes of manganese oxide layers as revealed in SEM studies. Pseudocapacitance of this oxide electrode was evaluated by cyclic voltammetry (CV) and chronopotentiometry (CHP) in 2 M NaOH solution. The specific capacitance of the Mn oxide electrode was as high as 1515 F $g^{-1}$, which was ten times higher than Mn oxide deposited on a flat Ni-ribbon. 80% of capacity was retained after 200 charge/discharge cycles. The system showed no loss of activity in dry form over period of days. The impedance studies indicated highly conducting $MnO_x$/P-Ni substance and the obtained specific capacitance from impedance data showed good agreement with the charge/discharge measurements.

• 한국분말재료학회지
• /
• 제19권4호
• /
• pp.297-303
• /
• 2012

In this study, voltammetry system for realizing high sensitivity nano-labeled sensor of detecting heavy metals was designed, and optimal system operating conditions were determined. High precision digital to analog converter (DAC) circuit was designed to control applied unit voltage at working electrode and analog to digital converter (ADC) circuit was designed to measure the current range of $0.1{\sim}1000{\mu}A$ at counter electrode. Main control unit (MCU) circuit for controlling voltammetry system with 150 MHz clock speed, main memory circuit for the mathematical operation processing of the measured current value and independent power circuit for analog/digital circuit parts to reduce various noise were designed. From result of voltammetry system operation, oxidation current peaks which are proportional to the concentrations of Zn, Cd and Pb ions were found at each oxidation potential with high precision.

• Bulletin of the Korean Chemical Society
• /
• 제35권2호
• /
• pp.569-574
• /
• 2014

Inverted bulk hetero-junction polymer solar cells (iPSC) composed of P3HT/PC61BM blends on the ZnO modified with benzoic acid derivatives-based self-assembled monolayers (SAM) are fabricated. Compared with the device using the pristine ZnO, the devices with ZnO surface modified SAMs derived from benzoic acid such as 4-(diphenylamino)benzoic acid (DPA-BA) and 4-(9H-carbazol-9-yl)benzoic acid (Cz-BA) as an electron transporting layer show improved the performances. It is mainly attributed to the favorable interface dipole at the interface between ZnO and the active layer, the eective passivation of the ZnO surface traps, decrease of the work function and facilitating transport of electron from PCBM to ITO electrode. The power conversion eciency (PCE) of iPSCs based on DPA-BA and Cz-BA treated ZnO reaches 2.78 and 2.88%, respectively, while the PCE of the device based on untreated ZnO is 2.49%. The open circuit voltage values ($V_{oc}$) of the devices with bare ZnO and SAM treated ZnO are not much different. Whereas, higher the fill factor (FF) and lower the series resistance ($R_s$) are obtained in the devices with SAMs modification.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.953-956
• /
• 2003

Transparent conductive ZnO:Ga thin films were deposited on glass substrates using rf magnetron sputtering method for flat panel display. The ZnO:Ga films were preferentially oriented to c-axis (002) of on substrates. The surface morphology was smooth and had not porous whatever substrate temperature was. The electrical conductivity of the thin films were in the range of $1.6{\times}10^2{\sim}6.7{\times}10^3\;{\Omega}^{-1}cm^{-1}$ at the growth temperature from 50 to $400^{\circ}C$, whereas has a maximum at around $250^{\circ}C$. By combining of XRD and EXAFS, the crystallinity and grain size decreased with increasing substrate temperature corresponding to the reduction of the grain-boundary scattering. The optical transmittance of sputtered ZnO:Ga thin films had an improved about 86% in the UV-visible region.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 D
• /
• pp.1379-1381
• /
• 1998

Powder electroluminescent device (PELD) structured conventionally dielectric and phosphor layer, between electrode and their layer fabricated by screen printing splaying or spin coating method. To promote performance of PELDs, we approached the experiments for different structure and thickness variation of PELD. Thickness variation($30{\mu}m{\sim}130{\mu}m$) was taken. To investigate electrical and optical properties of PELDs, EL spectrum, transferred charge density using Sawyer-Tower's circuit brightness was measured. Variation of structure in PELDs was as follows: WK-1 (ITO/BaTiO3/ZnS:Cu/Silver paste), WK-2 (ITO/BaTiO3/ZnS:Cu/BaTiO3/ZnS:Silver paste), WK-3 (ITO/BaTiO3/ZnS:Cu/BaTiO3/Silver paste), WK-4(ITO/BaTiO3+ZnS:Cu/Silver paste) As a result, structure of the highest brightness appeared WK-4 possessed 60 ${\mu}m$ thickness. The brightness was 2719 cd/$m^2$ at 100V, 400Hz.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 C
• /
• pp.1482-1484
• /
• 2002

Transparent conductive oxides (TCO) are necessary as front electrode for most thin film solar cell. In our paper, transparent conducting aluminum-doped Zinc oxide films (ZnO:Al) were prepared by rf magnetron sputtering on glass (Corning 1737) substrate as a variation of the deposition condition. After deposition, the smooth ZnO:Al films were etched in diluted HCI (0.5%) to examine the electrical and surface morphology properties as a variation of the time. The most important deposition condition of surface-textured ZnO films by chemical etching is the processing pressure and the substrate temperature. In low pressures (0.9mTorr) and high substrate temperatures $({\leq}300^{\circ}C)$, the surface morphology of films exhibits a more dense and compact film structure with effective light-trapping to apply the silicon thin film solar cells.