• Journal of the Korean institute of surface engineering
• /
• v.34 no.6
• /
• pp.537-544
• /
• 2001

In the present study, tin-zinc alloys were coated on a cold-rolled steel sheet with variations of electrolyte concentration, additives quantity and current density employing the Hull cell and circulation cell simulator. With an addition of additives of 2m1/L, tin-zinc deposits containing 10 to 40 percent Zn revealed a good surface appearance with weak acidic electrolytes. The organic additives suppressed the Sn deposition rate and thus increased the zinc contents in tin-zinc coating layers. The zinc contents in the tin-zinc coating layers depended almost linearly on the concentrations of metal ions of tin and zinc. Temperature of the electrolyte affected the composition tin-zinc coating layer. However, the concentration of complexants revealed little effectiveness. The surface morphology of tin-zinc coating showed dense tin and zinc phases with fine equiaxed grains with the high current density.

• Journal of Welding and Joining
• /
• v.15 no.6
• /
• pp.49-56
• /
• 1997

Effect of process parameters on the quality of condenser discharge weld for coated sheet steels was discussed. The welding specimens were coated with pure Zn of 20/20 g/m2 in the production line. Direct measurements of welding parameters such as the discharge current, the pressures and the voltage drop across the electrodes were carried out with welding process monitoring system. High speed camera was also utilized to analyze the weld formation process. Test results indicated that the relation between weld strength and applied energy was stabilized at the acceptable welding heat input range. It was thought that the acceptable welding heat input should be redefined based on the monitored data because the calculated value of the welding heat input could hardly be utilized if the discharge condition was changed. Mechanical test results and high speed photographs showed that expulsion deteriorated the weld quality and the strength at the same time especially when the size of the spatter was large enough to carry the molten metal, which should form the nugget, out of the welding spot. Results also demonstrated that the discharge current should be applied at the appropriate time during the process because sufficient nugget was not produced if the time was deviated from the optimum range.

• Corrosion Science and Technology
• /
• v.12 no.6
• /
• pp.295-303
• /
• 2013

Silane surface treatments have been developed as an alternative for toxic and carcinogenic chromate-based treatments for years. It is consistently observed that ultra-thin films offer excellent corrosion protection as well as paint adhesion to metals. The silane performance is comparable to, or in some cases better than, that of chromate layers. Based on the tetra-ethylorthosilicate(TEOS) and methlyl trieethoxysilane(MTES), inorganic sol was synthesized and formed hybrid networks with $SiO_2$ nano particle and polypropylene glycol(PPG) on Zn alloyed steel surface. According to SST results, addition of 10nm and 50nm $SiO_2$ nanoparticle in synthesized solution improved anti-corrosion property by its shear stress relaxation effect during curing process. Also, SST results were shown that anti-corrosive property was affected by the amounts of organic compounds.

• Korean Journal of Metals and Materials
• /
• v.49 no.4
• /
• pp.281-290
• /
• 2011

In order to gain better understanding of the selective surface oxidation and its influence on the galvanizability of a transformation-induced plasticity (TRIP) assisted steel containing 1.5 wt.% Si and 1.6 wt.% Mn, a model experiment has been carried out by depositing Si and Mn (each with a nominal thickness of 10 nm) in either monolayers or bilayers on a low-alloy interstitial-free (IF) steel sheet. After intercritical annealing at $800^{\circ}C$ in a $N_2$ ambient with a dew point of $-40^{\circ}C$, the surface scale formed on 590 MPa TRIP steel exhibited a microstructure similar to that of the scale formed on the Mn/Si bilayer-coated IF steel, consisting of $Mn_{2}SiO_{4}$ particles embedded in an amorphous $SiO_{2}$ film. The present study results indicated that, during the intercritical annealing process of 590 MPa TRIP steel, surface segregation of Si occurs first to form an amorphous $SiO_{2}$ film, which in turn accelerates the out-diffusion of Mn to form more stable Mn-Si oxide particles on the steel surface. During hot-dip galvanizing, particulate $Fe_{3}O_{4}$, MnO, and Si-Mn oxides were reduced more readily by Al in a Zn bath than the amorphous $SiO_{2}$ film. Therefore, in order to improve the galvanizability of 590 TRIP steel, it is most desirable to minimize the surface segregation of Si during the intercritical annealing process.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.44-44
• /
• 2018

칼라도장강판은 금속 제품의 제품화 공정 중에 도장 공정을 생략함으로 경제적이며, 제조공정 중 발생할 수 있는 VOCs(Volatile Organic Compounds)의 배출 염려가 없어 건축 및 가전 산업에 다용되고 있다. 칼라도장강판은 용융아연도금강판(GI), 전기아연도금강판(EGI), 용융알루미늄아연합금도금강판 등이 기재로 적용되고 있으며, 최근 마그네슘 성분이 첨가되는 고내식 도금강판 개발과 함께 고내식 도금강판을 이용한 칼라도장강판의 개발 및 수요 발굴을 위한 연구가 활발하게 진행 중에 있다. 칼라강판의 구성은 일반적으로 도막 밀착성 확보를 위한 화성처리층, 기재와 도막간의 밀착성과 내식성 개선을 위한 하도층(primer layer), 가공성, 내오염성, 의장성 등의 기능성 부여를 위한 상도층(top layer)의 구조로 도장되어 있다. 도료는 가공성, 내오염성, 경도 등의 기능성이 우수한 폴리에스테르 수지계가 가장 폭넓게 사용되고 경화제로는 멜라민 화합물과 이소시아네이트 화합물이 널리 사용되고 있다. 칼라도장 강판은 1970년대 이후 본격적으로 보급되어 사용되기 시작하였으며, 화성처리층은 밀착성과 내식성이 우수한 크로메이트처리가 널리 사용되고, 하도층은 방청성이 우수한 크로메이트계 방청 안료를 함유시킨 도료가 일반적이다. 그러나, 전기전자 제품에 적용되는 칼라도장강판은 2006년에 RoHS 규제의 시행과 더불어 6가 크롬 사용 제한의 영향으로 크롬프리 화성처리가 일반화되어 적용되고 있으며, 그 동안 6가 크롬 제안이 유보적이었던 건축용 칼라도장강판 또한 크롬프리 화성처리층 및 크로메이트계 방청 안료의 하도층 적용을 회피하고 있는 추세이다. 이에 따라, 고내식 합금도금강판을 기재로 사용하고 기존의 화성처리층과 하도층에 크롬프리 수지를 적용하는 연구개발이 활발하게 진행 중에 있다. 본 연구에서는 마그네슘이 첨가된 고내식 합금도금강판으로 Al-Mg-S i강판과 용융 Zn-Al-Mg 합금도금강판에 기존의 상용화 공정에서 사용되는 크롬계 및 크로프리 화성처리 적용 칼라도장강판에 대한 내식성 등 칼라도장강판의 특성에 대해 발표한다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.1109-1112
• /
• 2015

A milatary ship without degaussing coil has a vertical magnetization to compensate magnetization induced by the vertical magnetic field component of earth magnetic field during demagnetization process. Flash D is very useful to acquire vertical magnetization. However this is hard to predict vertical magnetization. This experiment was investicated on another method, which used the only vertical bias magentic field. The specimens were prepared by thin Zn coated steel sheet with a thickness of 0.15mm. The shapes of 3 specimes was rectangular, triangular and circular cylinders. These shapes were corresponded to the shapes of bow, mid and stern of a vessel. Through FEM analysis, the difference of magnetic signatures for these specimens was recognized and the residual magnetization curve was measured. magnetic field was generated by a solenoid coil and magnetic signature was measured by a magnetic field sensor. A linearity between a vertical bias magnetic field and a vertical manetzation existed and the vertical magnetization of a miltary vessel was predicted by the linearity.