• Bulletin of the Korean Chemical Society
• /
• v.26 no.7
• /
• pp.1083-1089
• /
• 2005

Most experimental studies available in the literature on filtration are based on observed average zeta potential of particles (usually 10 measurements). However, analyses of data using the average zeta potential alone can lead to misleading and erroneous conclusions about the attachment behavior because of the variation of particle zeta potentials and the heterogeneous distribution of the collector surface charge. To study characteristics of zeta potential, zeta potential distributions (ZPDs) of silica particles under 9 different chemical conditions were investigated. Contrary to many researchers’ assumptions, most of the ZPDs of silica particles were broad. The solids concentration removal was better near the isoelectric point (IEP) as many researchers have noticed, thus proper destabilization of particles is very important to achieve better particle removal in particle separation processes. While, the mean zeta potential of silica particles at a given coagulant dose was a function of particle concentration; the amount of needed coagulant for particle destabilization was proportional to the total surface charge area of particles in the suspension.

• Journal of Korean Society of Water and Wastewater
• /
• v.19 no.4
• /
• pp.437-445
• /
• 2005

Zeta potential is a key parameter of double layer repulsion for individual particles and can usually be used to interpret the trend of coagulation efficiency. This study focused on the measurement of zeta potential of algae and clay under various experimental conditions including water characteristics (pure water, stream water, reservoir water) and coagulant dose (10~50 mg/L). Results showed that the variation of zeta potential was highly sensitive depending on the water characteristics and coagulation conditions. Zeta potential of two genera of algae (anabaena sp. and microcystis sp.) were changed highly with coagulant dosage, especially. On the basis of trajectory analysis, bubble-floc collision efficiency simulated in terms of zeta potential was fitted well with removal efficiency of chlorophyll-a from algae particles. It was found that the control of zeta potential was important for effective removal of algae particles.

• Geomechanics and Engineering
• /
• v.2 no.3
• /
• pp.191-202
• /
• 2010

The porosity (including the specific surface area and pore volume-diameter distribution) of montmorillonitic soft rock (MSR) was studied experimentally with an electrochemical treatment, based on which the change in porosity was further analyzed from the perspective of its electrokinetic potential (${\zeta}$ potential) and the isoelectric point of the electric double layer on the surface of the soft rock particles. The variation between the ${\zeta}$ potential and porosity was summarized, and used to demonstrate that the properties of softening, degradation in water, swelling, and disintegration of MSR can be modified by electrochemical treatment. The following conclusions were drawn. The specific surface area and total pore volume decreased, whereas the average pore diameter increased after electrochemical modification. The reduction in the specific surface area indicates a reduction in the dispersibility and swelling-shrinking of the clay minerals. After modification, the ${\zeta}$ potential of the soft rock was positive in the anodic zone, there was no isoelectric point, and the rock had lost its properties of softening, degradation in water, swelling, and disintegration. The ${\zeta}$ potential increased in the intermediate and cathodic zones, the isoelectric point was reduced or unchanged, and the rock properties are reduced. When the ${\zeta}$ potential is increased, the specific surface area and the total pore volume were reduced according to the negative exponent law, and the average pore diameter increased according to the exponent law.

• Tribology and Lubricants
• /
• v.33 no.5
• /
• pp.228-233
• /
• 2017

Chemical Mechanical Polishing of chemically stable sapphire substrates is dominantly affected by the mechanical processing of abrasives, in terms of the material removal rate. In this study, we investigated the effect of electrostatic force between the abrasives and substrate, on the polishing. If potassium chloride (KCl) is added to slurry, water molecules are decomposed into $H^+$ and $OH^-$ ions, and the amount of ions in the slurry changes. The zeta potential of the abrasives decreases with an increase in the amount of $H^+$ ions in the stern layer; consequently, the electrostatic force between the abrasives and substrate decreases. The change in zeta potential of abrasives in the slurry is affected by the slurry pH. In acidic zones, the amount of ions bound to the abrasives increases if the amount of $H^+$ ions is increased by adding KCl. However, in basic zones, there is no change in the corresponding amount. In acidic zones, zeta potential decreases as molar concentration of potassium increases; however, it does not change significantly in basic zones. The removal rate tends to decrease with increase in molar amount of potassium in acidic zones, where zeta potential changes significantly. However, in basic zones, the removal rate does not change with zeta potential. The tendencies of zeta potential and that of the frictional force generated during polishing show strong correlation. Through experiments, it is confirmed that the contact probability of abrasives changes according to the electrostatic force generated between the abrasives and substrate, and variation in removal rate.

• Journal of Korean Society on Water Environment
• /
• v.28 no.1
• /
• pp.115-120
• /
• 2012

Different colloidal particles generally co-exist in the water and wastewater. Thus, there needs to identify practical electrokinetic characteristics of the particles, comparing with the case when each colloidal material is independently distributed. In this study, changes of overall zeta potential was examined through mixed dispersions of $TiO_{2}$ and $MnO_{2}$. The mixing ratios were classified into 3-type in order to distinguish the effects of the proportions of each particle from those of total concentration in colloidal suspensions. The types are single colloidal dispersions of $TiO_{2}$ and $MnO_{2}$ (1:0, 0:1), mixed dispersions at different ratios (0.75:0.25, 0.5:0.5, 0.25:0.75), and a mixed dispersion with doubled concentration (1:1), respectively. It showed that the overall variation of zeta potential as a function of pH was intensified in a colloidal dispersion with the ratio of 1:1. It was concerned that the double action of ion would contribute to this result. On the one hand, the zeta potentials of each colloidal dispersion commonly decreased at the state of strong acid and base under the influence of compression of the electric double layer. The changing patterns were also considered through calculating total interaction energy between colloidal particles based on DLVO theory and measuring turbidity of the colloidal dispersions.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.4
• /
• pp.640-645
• /
• 1987

Surface states and interfacial phenomena at the undoped polycrystalline semiconductor particale-electrolyte interfaces were qualitatively analyzed based on the zeta potentials which were measured with microelectrophoresis measurements. The suspensions were composed of the undoped polycrystaline silicon(Si) or gallium arsenide (GaAs) semiconductor particles stalline Si and GaAs particles in the KCl electrolytes was 3.73~6.2x10**-4 cm\ulcornerV.sec and -2.3~1.4x10**-4cm\ulcornerV.sec at the same conditions, respectively. The range of zeta potentials corresponding to the electrophoretic mobilities is 47.8~80.1mV and -30.1~17.9mV, respectively. The variation of the zeta potentials of the undoped polycrystalline Si was similar to the doped crystalline Si. On the other hand, two points of zeta potential reversal occurred at the undoped polycrystalline GaAs-KCl electrolyte interfaces. The surface states of the undoped polycrystalline Si and GaAs were dominated by positively charged donor surface states. These surface states are attributed to adsorbed ion surface states (slow states) at the semiconductor oxide layer-electrolyte interfaces.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1288-1291
• /
• 2004

In this study, physical characteristics of alumina slurry on variation of pH value and the effect of non-ionic surfactants on alumina slurry for copper chemical mechanical planarization (CMP) slurry have been investigated. After pH value of the slurry with alumina abrasive was changed by adding various amount of $HNO^3$ or KOH, the differences of settling rate, particle size, and zeta-potential were estimated. Better settling rates were shown in slurries with alumina abrasive at near pH 1. Higher zeta-potential was shown at around pH 2 in alumina slurry and the point of zero charge (PZC) was measured at about pH $9\sim10$. Non-ionic surfactant was added in the slurry with 5wt% alumina abrasive to get its effect on slurry practically. Abrasive size was smaller increased when amount of surfactant increased in slurry with P-4 as abrasive; on the other side, it was smaller when amount of surfactant decreased with AES-12. Variation of zeta-potential has no tendency with adding surfactant; however, values of zeta-potential were between $35\sim50mV$. The proper amount of surfactant was $0.1\sim1.0wt%$ in slurry with P-4 and $0.5\sim1.0wt%$ in slurry with AES-12 respectively. Excellent dispersion stabilization was obtained by addition of non-ionic surfactant

• Tribology and Lubricants
• /
• v.7 no.2
• /
• pp.46-50
• /
• 1991

The Frictional behavior in single crystal (111) p-type silicon as influenced by electolytic solutions have been studied. Linear scratching by diamond indentor was carried out to show the variation of friction between silicon and diamond indentor immersed in electrolytic solutions. The results indicate that concentration of the solutions influence the fricational coefficient. In addition there is a correlation between measured zeta-potential and frictional coefficients. The zeta-potential in various concentrations was measured to estimate the variation of the Peierls energy. The proposed model predicts a minimum frictional coefficient near a concentration of $10^{-3}$ M/l NaOH in deionized water and explains the chemomechanical effect observed in this study.

• Environmental Sciences Bulletin of The Korean Environmental Sciences Society
• /
• v.4 no.3
• /
• pp.173-183
• /
• 2000

This study measured the zeta potential of both latex colloidal particles with carboxylate surface groups and glass beads (collectors) with silanol surface group employing various solution with different chemical characteristics. The results have been compared with the surface chemistry theory. The zeta potential of the particle and collector increased with increasing pH up to 5.0 regardless of the solution chemistry. For a monovalent electrolyte solution(sodium chloride solution) the zeta potential steadily increased until the pH reached 9.5. In contrast, little change in zeta potential was made between 5.0 and 9.5 for a divalent electrolyte solution (sodium chloride solution) the zeta potential steadily increased until the pH reached 9.5. In contrast, little change in zeta potential was made between 5.0 and 9.5 for a divalent electrolyte solution (calcium chloride solution). In other words, the more the pH decreases, the larger the effect of neutral salts, such as NaCl and CaCl$_2$, have on the ζ-potential values. In this study, the PZPC(point of zero proton condition) of the particle and collector occurred below a pH of 3.1, H(sup)+ and OH(sup)- acted as a PDI (potential determining ion), and Na(sup)+ acted as an IDI(indifferent ion). The magnitude of the negative ζ-potential values of the particle and collector monotonically increased as the concentrations of Na(sup)+ or Ca(sup)2+([Na(sup)+] or [Ca(sup)2+]) decreased (the values of pNa or pCa increased). In the case of latex particles, the ζ-potential should aproach zero (isoelectric point; IEP) asymptotically as the pNa approaches zero, while in the case of calcium chloride electrolyte, ζ-potential reversal may be expected to occur around 3.16$\times$10(sup)-2MCaCl$_2$(pCa=1.5). pH, valance and ionic strength can be used in various ways to improve the water treatment efficiency by modifying the charge characteristics of the particle and collector. Predictive capability is far less certain when EDL(electrical double layer) repulsive forces exist between the particle and collector.

• Journal of Soil and Groundwater Environment
• /
• v.7 no.3
• /
• pp.85-94
• /
• 2002

Overall objective of this study was to evaluate the electrochemical characteristics of fine soils during the electrokinetic(EK) remediation. Zeta potential of kaolinite as a function of solution pH and surfactant concentration was investigated to make a relationship with electroosmotic flow direction and rate. During the EK experiments, pH of pore solution, electroosmotic permeability($k_e$), electric conductivity($\delta_e$) and voltage distribution was measured, respectively, The point of zero charge(PZC) of kaolinite was estimated to be about 4.2 and the zeta potential of kaolinite above PZC was more negative as solution pH increased. Sorption of surfactants on the kaolinite altered the zeta potential of kaolinite. resulting from the variation of electrochemical characteristics of kaolinite surface. hs the EK experiment progressed, low pH was predominant over most of the kaolinite specimen and thus resulted in very low mass and charge flow. The $k_e$ and $\delta_e$ was also affected by the variation of voltage drop across the EK column with time. Results from this study implied that zeta potential of kaolinite affected by the pH variation of pore solution and voltage distribution in soil column played important role in the determination of mass and charge flow during EK process. It was also suggested that pH adjustment or addition of suitable sorbates could alter the electrochemical characteristics of soil surface and thus maintain high mass and charge flow rate with time.