• Advances in aircraft and spacecraft science
• /
• 제2권3호
• /
• pp.329-343
• /
• 2015

This study aimed to observe the effect of a novel concept (referred to as the flap extension) implemented on the leading edge of the flap of a three element high lift device. The high lift device, consisting of a flap, main element and slat is designed around an Airbus research profile for sufficient take off and landing performance of a large commercial aircraft. The concept is realised on the profile and numerically optimised to achieve an optimum geometry. Two different optimisation approaches based on Genetic Algorithm optimisations are used: a zero order approach which makes simplifying assumptions to achieve an optimised solution: as well as a direct approach which employs an optimisation in ANSYS DesignXplorer using RANS calculations. Both methods converge to different optimised solutions due to simplifying assumptions. The solution to the zero order optimisation showed a decreased stall angle and decreased maximum lift coefficient against angle of attack due to early stall onset at the flap. The DesignXplorer optimised solution matched that of the baseline solution very closely. The concept was seen to increase lift locally at the flap for both optimisation methods.

• 응용통계연구
• /
• 제29권7호
• /
• pp.1459-1473
• /
• 2016

시간의 흐름에 따라 관측되는 경시적(longitudinal) 자료의 경우, 경시적 자료와 생존(survival) 자료가 종종 동시에 수집된다. 이 때 경시적 자료에서 발생하는 결측이 생존자료와의 연관성으로 인해 발생한 무시할 수 없는 결측(non-ignorable missing)이라면, 경시적 자료분석 방법만으로는 두 자료 간의 연관성을 고려하지 않아 독립변수에 대한 효과는 편향된 결과를 얻게 된다. 이러한 문제를 해결하기 위해서 결측의 원인이 생존시간과 연관되어 있으므로 생존모형을 고려하여 불편추정량을 얻기 위해 경시적 자료와 생존자료의 결합모형에 대한 연구가 이루어져 왔다. 본 논문은 경시적 자료의 형태가 영이 많이 존재하는 영과잉 가산자료(zero-inflated count data)와 생존자료의 결합모형을 연구하였다. 경시적 영과잉 가산자료와 생존자료는 각각 허들모형(hurdle model)과 비례위험모형(proportional hazards model)의 부 모형을 적용하였고, 두 부 모형들의 변량효과가 다변량 정규분포를 따른다는 가정을 통하여 결합하였다. 모수의 최우추정법으로 EM 알고리즘을 활용하였고, 추정된 표준오차를 계산하기 위해 프로파일 우도(profile likelihood)를 이용하였다. 최종적으로 모의실험을 통해 두 부 모형의 변량효과 간 상관관계가 존재하는 경우 결합모형이 개별적 모형보다 편의와 포함확률(coverage probability)의 측면에서 더 우수함을 보였다.

• Journal of Korean Neurosurgical Society
• /
• 제61권5호
• /
• pp.574-581
• /
• 2018

Objective : The zero-profile implant (Zero-P) is accepted for use in anterior cervical fusion for the treatment of degenerative cervical disease. However, evidence pertaining to its efficiency and safety in traumatic cervical injury is largely insufficient. This study aimed to compare the overall outcomes of patients who underwent Zero-P for traumatic cervical disc injury. Methods : Data from a total of 53 consecutive patients who underwent surgery for traumatic or degenerative cervical disc disease using the Zero-P were reviewed. Seventeen patients (group A) had traumatic cervical disc injury and the remaining 36 (group B) had degenerative cervical disc herniation. The fusion and subsidence rates and Cobb angle were measured retrospectively from plain radiographs. The patients' clinical outcomes were evaluated using the Japanese Orthopedic Association (JOA) score and Odom's criteria. Results : The C2-7 Cobb and operative segmental angles increased by $3.45{\pm}7.61$ and $2.94{\pm}4.59$ in group A; and $2.46{\pm}7.31$ and $2.88{\pm}5.49$ in group B over 12 postoperative months, respectively. The subsidence and fusion rate was 35.0% and 95.0% in group A; and 36.6% and 95.1% in group B, respectively. None of the parameters differed significantly between groups. The clinical outcomes were similar in both groups in terms of increasing the JOA score and producing a grade higher than "good" using Odom's criteria. Conclusion : The application of Zero-P in patients with traumatic cervical disc injury was found to be acceptable when compared with the clinical and radiological outcomes of degenerative cervical spondylosis.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.61.1-61.1
• /
• 2015

Nanoscale semiconductor plasma processing has become one of the most challenging issues due to the limits of physicochemical fabrication routes with its inherent complexity. The mission of future and emerging plasma processing for development of next generation semiconductor processing is to achieve the ideal nanostructures without abnormal profiles and damages, such as 3D NAND cell array with ultra-high aspect ratio, cylinder capacitors, shallow trench isolation, and 3D logic devices. In spite of significant contributions of research frontiers, these processes are still unveiled due to their inherent complexity of physicochemical behaviors, and gaps in academic research prevent their predictable simulation. To overcome these issues, a Korean plasma consortium began in 2009 with the principal aim to develop a realistic and ultrafast 3D topography simulator of semiconductor plasma processing coupled with zero-D bulk plasma models. In this work, aspects of this computational tool are introduced. The simulator was composed of a multiple 3D level-set based moving algorithm, zero-D bulk plasma module including pulsed plasma processing, a 3D ballistic transport module, and a surface reaction module. The main rate coefficients in bulk and surface reaction models were extracted by molecular simulations or fitting experimental data from several diagnostic tools in an inductively coupled fluorocarbon plasma system. Furthermore, it is well known that realistic ballistic transport is a simulation bottleneck due to the brute-force computation required. In this work, effective parallel computing using graphics processing units was applied to improve the computational performance drastically, so that computer-aided design of these processes is possible due to drastically reduced computational time. Finally, it is demonstrated that 3D feature profile simulations coupled with bulk plasma models can lead to better understanding of abnormal behaviors, such as necking, bowing, etch stops and twisting during high aspect ratio contact hole etch.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2004년도 학술발표회
• /
• pp.957-960
• /
• 2004

From a water-environmental point of view, with a change of understanding and concern about vegetation, it changes that vegetation acts as stability of channel and bed, providing habitats and feed for fauna, and means improving those with appreciation of the beautiful but resistant factor to the flow So, it becomes important concern and study subjects that turbulent structure by vegetation, shear stress and transport as well as roughness and average velocity by vegetation. But from a hydraulic point of view, vegetation causes resistance to the flow and can increase the risk of flooding, Therefore, this thesis concern the flow characteristics in vegetated open channels. According to the experimental results, $z_0$ was on an average $0.4h_p$ in a vegetated open channel. So, the elevation corresponding to zero velocity in a vegetated channel was the middle of roughness element. The limit for logarithmically distributed profile over the roughness element was from $z_0$ to $0.80h_{over}$ for a vegetated channel. Among the existing theory, the method of Kouwen et al.(1969), Haber(1982), and El-Hakim and Salama(1992) except Stephan(2001) gave a very good value compared to the measured velocity profile.

• Journal of Magnetics
• /
• 제6권3호
• /
• pp.86-89
• /
• 2001

Microstructure modifications are investigated for annealed Co-based amorphous ribbon in vacuum and open air. X-ray diffraction (XRD) spectra for annealed sample in vacuum indicate atomic arrangements with initial nucleation of hcp-Co crystallite at 38$0^{\circ}C$ annealing temperature. However, the XRD spectra in samples with long annealing times of $t_a\geq300$ min demonstrate sharp and good developed surface crystalline hcp-, fcc- Co and $Co_2$Si phases. The giant magnetoimpedance (GMI) profile at 0.1 MHz displaying one-peak behavior in vacuum annealed samples at T = 38$0^{\circ}C$ irrespective of annealing time $t_a$ from 20 to 480 mim. For the annealed samples in an open air, the GMI profile shows two-peaks for $t_a$ = 20 min annealed sample. However, one of peaks disappears and an asymmetric GMI profile exhibits a drastic step-like change near zero field for $t_a\geq300$min. Such asymmetric GMI characteristics is related to the surface microstructures of fcc-Co, hop-Co and $Co_2$Si crystalline phases.

• 한국수소및신에너지학회논문집
• /
• 제33권5호
• /
• pp.557-565
• /
• 2022

The effect of flow configuration in ammonia-fed solid oxide fuel cell are investigated by using a three-dimensional numerical model. Typical flow configurations including co-flow and counter-flow are considered. The ammonia is directly fed into the stack without any external reforming process, resulting in an internal decomposition of NH3 in the anode electrode of the stack. The result showed that temperature profile in the case of counter-flow is more uniform than the co-flow configuration. The counter-flow cell, the temperature is highest at the middle of the channel while in the case of co-flow, the temperature is continuously increased and reached maximum value at the outlet area. This leads to a higher averaged current density in counter-flow compared to that of co-flow, about 5%.

• Macromolecular Research
• /
• 제11권3호
• /
• pp.183-188
• /
• 2003

The controlled delivery of anticancer agents using biodegradable polymeric implant has been developed to solve the problem of penetration of blood brain barrier and severe systemic toxicity. This study was performed to prepare 5-FU-loaded poly (L-lactide-co-glycolide) (PLGA) wafer fabricated microparticles prepared by two different method and to evaluate their release profile for the application of the treatment of brain tumor. 5-FU-loaded PLGA microparticles were characterized by scanning electron microscopy (SEM), powder X-ray diffraction (XRD), and differential scanning calorimetry (DSC). SEM observation of the 5-FU-loaded PLGA microparticles prepared by rotary solvent evaporation method showed that 5-FU was almost surrounded by PLGA and significant reduction of crystallinity of 5-FU was confirmed by XRD. In case of release profile of 5-FU from 5-FU-loaded PLGA wafer fabricated microparticles prepared by mechanical mixing, the release profile of 5-FU followed near first order release kinetics. In contrast to the above result, release profile of 5-FU from 5-FU-loaded PLGA wafer fabricated microparticles prepared by rotary solvent evaporation method followed near zero order release kinetics. These results indicate that preparation method of the 5-FU-loaded PLGA microparticles to fabricate into wafers was contributed to drug release profile.

• Journal of Magnetics
• /
• 제16권1호
• /
• pp.6-9
• /
• 2011

Spin-motive force has drawn attention because it contains a fundamental physical property. Spin-motive force creates effective electric and magnetic fields in moving magnetization; a vortex is a plausible system for observing the spin-motive force because of the abrupt profile of magnetization. However, the time-averaged value of a spin-motive force becomes zero when a vortex core undergoes gyroscopic motion. By means of micromagnetic simulation, we demonstrates that a non-zero time-averaged electric field induced by spin-motive force under certain conditions. We propose an experimental method of detecting spin-motive force that provides a better understanding of spin transport in ferromagnetic system.

• Journal of Pharmaceutical Investigation
• /
• 제29권4호
• /
• pp.343-348
• /
• 1999

The purpose of this study is to prepare the controlled release adhesive patch containing naproxen. Pressuresensitive adhesive (PSA)-type patch was fabricated by casting of polyisobutylene (PIE.) and mineral oil in toluene. Membrane-controlled release (MCR)-type patch was prepared by the attachment of the controlled release membrane on the PSAtype patch. The membrane was mainly composed of Eudragit, polyethylene glycol(PEG) and glycerin. The drug release profile and skin permeation test with various patches were evaluated in vitro. The release of naproxen from PIE-based PSAtype patch with various loading doses fitted Higuchi's diffusion equation. However, the permeation of naproxen through hairless mouse skin from PSA-type patch followed zero-order kinetics. In MCR-type patch, thickness of controlled release membrane affected on the drug release rate highly. In the composition of membrane, the release rate was decreased as the ratio of Eudragit increased. The drug release from the MCR-type patch followed zero order kinetics. The permeation of naproxen through hairless mouse skin from MCR-type patch showed lag time for the intial release period and didn't fit the zero-order kinetics