• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.10
• /
• pp.595-600
• /
• 2002

This paper presents the analyzed results of dynamic characteristics including steady state characteristics of the boost input type ZVS converter using the active clamp circuit by the state space averaging method. From the results, it can be seen that the converter has the 5th order transfer functions and the stable closed loop characteristic is obtained by using the compensated error amplifier with 2-pole and 1-zero. The validity of all analyzed results are verified by measurement.

• Journal of Power Electronics
• /
• v.15 no.6
• /
• pp.1577-1583
• /
• 2015

In this research, a combined adaptive-robust current controller is developed for non-minimum-phase DC-DC converters in a wide range of operations. In the proposed nonlinear controller, load resistance, input voltage and zero interval of the inductor current are estimated using developed adaptation rules and knowing the operating mode of the converter for the closed-loop control is not required; hence, a single controller can be employed for a wide load and line changes in discontinuous and continuous conduction operations. Using the TMS320F2810 digital signal processor, the experimental response of the proposed controller is presented in different operating points of the buck/boost converter. During transition between different modes of the converter, the developed controller has a better dynamic response compared with previously reported adaptive nonlinear approach. Moreover, output voltage steady-state error is zero in different conditions.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.10
• /
• pp.2310-2316
• /
• 1997

This paper presents a comparative performance analysis of the stochastic gradient adaptive algorithm based on the least mean absolute third (LMAT) error criterion with other widely-used competing adaptive algorithms. Under the assumption that the signals involved are zero-mean, wide-sense stationary and Gaussian, approximate expressions that characterize the steady-state mean-squared estimation error of the algorithm is dervied. The validity of our derivation is then confirement by computer simulations. The convergence speed is compared under the condition that the LMAT and other competing algorithms converge to the same value for the mean-squared estimation error in the stead-state, and superior convergence property of the LMAT algorithm is observed. In particular, it is shown that the LMAT algorithm converges faster than other algorithms even through the eignevalue spread ratio of the input signal and measurement noise power change.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.6
• /
• pp.1-7
• /
• 2003

This paper introduces a robust sliding mode repetitive control method for a class of nonlinear system. The sliding mode controller stabilizes the overall system and makes the tracking error converge to some residual set. Also, tile repetitive learning controller makes the tracking error converge to zero. Unlike other methods, the proposed sliding mode controller reduces the chattering effects in the steady state without using high-order sliding manifold approach.

• Journal of Institute of Control, Robotics and Systems
• /
• v.2 no.3
• /
• pp.181-187
• /
• 1996

A frictionless positioning device using cone-shaped active magnetic bearings(AMBs) is developed, which is driven by a brushless DC motor equipped with resolver. The cone-shaped AMB feature that the structure is simple and yet the five d.o.f. rotor motion is controlled by four magnet pairs. A linearized dynamic model, which accounts for the relationship between input voltage and output current in the cone-shaped magnet, is developed and the azimuth motion of the frictionless positioning device is modeled as the second order system. The feedback controller is designed by using linear quadratic regulator with integral action optimal control law so that the cone-shaped AMB system is stabilized and the frictionless positioning device gets the zero steady state. It is observed that the linearized dynamic model is adequate and the frictionless positioning device can achieve the tracking accuracy within the sensor resolution.

• Journal of Korea Society of Industrial Information Systems
• /
• v.5 no.1
• /
• pp.31-36
• /
• 2000

This paper presents a design method of deadbeat controller for DC motor driving a rotational system with gear. The deadbeat-response design developed for control system of a sampled continuous-data process does not guarantee zero intersampling ripples, but the proposed deadbeat control system that consists of the integral controller and the full-order state observer, and zero-order hold using in continuous systems, has many advantages such as an output response without the ripples and reaching the steady state without error after a given sampling period and faster settling time than the optimal control system in the same sampling period. The results of a case study through matlab simulation are shown that the efficiency of the proposed controller for DC motor driving a rotational system with gear is verified by comparing with optimal controller etc.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.579-582
• /
• 1999

This paper presents a design method of deadbeat controller for DC motor driving a rotational system with gear. The results of sampling a continuous-data process does not guarantee that no ripples occur between the sampling instants in the continuous-data output, but the proposed deadbeat control system that consists of the integral controller and the full state observer, and zero order hold using in continuous systems, has many advantages of such as an output response without the ripple and reaching the steady state without error after a given sampling period and faster settling time than the optimal control system in the short sampling period. The results of case study through matlab simulation shown that the efficiency of the proposed controller for DC motor driving a rotational system with gear, is verified by comparing with optimal controller etc.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10a
• /
• pp.149-154
• /
• 1990

In this paper, simulation results of a robust digital tracking controller on a robotic manipulator are presented. The objective is to follow a ramp reference input with zero steady state error in the presence of a disturbance and system parameter variations. Some of the difficulties are caused by the Coulomb frictions, the disturbance due to the gravitational pull, the spring effect of a link between the drive motor and the manipulator arm. Another difficulty is that, because of the non-differentiable Coulomb friction, the digital control system cannot be represented as a discrete system. It is thus necessary to design the controller based on a discrete-continuous hybrid model. The controller is based on feeding back the state variables and augmenting the system by addition discrete integrators. The feedback gain parameters are obtained by applying the quadratic optimal control theory and then choosing the new weighting matrices to eliminate the limit cycle by using the describing function method for hybrid system.

• Journal of Power Electronics
• /
• v.5 no.2
• /
• pp.151-159
• /
• 2005

The errors generated from current measurement paths are inevitable, and they can be divided into two categories: offset error and scaling error. The current data including these errors cause periodic speed ripples which are one and two times the stator electrical frequency respectively. Since these undesirable ripples bring about harmful influences to motor driving systems, a compensation algorithm must be introduced to the control algorithm of the motor drive. In this paper, a new compensation algorithm is proposed. The signal of the integrator output of the d-axis current regulator is chosen and processed to compensate for the current measurement errors. Usually the d-axis current command is zero or constant to acquire the maximum torque or unity power factor in the ac drive system, and the output of the d-axis current regulator is nearly zero or constant as well. If the stator currents include the offset and scaling errors, the respective motor speed produces a ripple related to one and two times the stator electrical frequency, and the signal of the integrator output of the d-axis current regulator also produces the ripple as the motor speed does. The compensation of the current measurement errors is easily implemented to smooth the signal of the integrator output of the d-axis current regulator by subtracting the DC offset value or rescaling the gain of the hall sensor. Therefore, the proposed algorithm has several features: the robustness in the variation of the mechanical parameters, the application of the steady and transient state, the ease of implementation, and less computation time. The MATLAB simulation and experimental results are shown in order to verify the validity of the proposed current compensating algorithm.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.9
• /
• pp.1617-1624
• /
• 2006

This paper presents system modeling, modified space vector PWM implementation and design of a closed loop controller of the Z-source inverter which consists of L and C components and shoot-through zero vectors for DGS. Zero vector periods of SVPWM utilized to boost DC-link voltage instead of conventional DC/DC converter and transformer. Only two shoot-through vut(nn are used for DC link voltage control during one switching period without loss of non-zero vectors. Discrete time sliding mode controller, robust servomechanism controller are designed to realize fast and no-overshoot current response and a steady state voltage error. Simulation results are shows the effectiveness of the proposed algorithm.