• 한국해양공학회지
• /
• 제30권1호
• /
• pp.18-24
• /
• 2016

Stabilizer fins are installed on each side of a ship to control its roll motion. The most common stabilizer fin is a rolling control system that uses the lift force on the fin surface. If the angle of attack of a stabilizer fin is zero or the speed is zero, it cannot control the roll motion. The Coanda effect is well known to generate lift force in marine field. The performance of stabilizer fin that applies the Coanda effect has been verified by model tests and numerical simulations. It was found that a stabilizer fin that applied the Coanda effect at Cj = 0.085 and a zero angle of attack exactly coincided with that of the original fin at α = 26°. In addition, the power needed to generate the Coanda effect was not high compared to the motor power of the original stabilizer fin.

• 한국환경과학회지
• /
• 제20권7호
• /
• pp.839-843
• /
• 2011

We have established a wind map of Singapore, a city-state characterized its land cover by urban buildings to confirm a possibility of wind farm development. As a simple but useful approximation of urban canopy, a zero-plane displacement concept was employed. The territory is divided into 15 sectors having similar urban building layouts, and zero-plane displacement, equivalent roughness height at each sector was calculated to setup a terrain boundary condition. Annual mean wind speed and mean wind power density map were drawn by a CFD micrositing model, WindSim where Changi International Airport wind data was used as an in-situ measurement. Unfortunately, predicted wind power density does not exceed 80 $W/m^2$ at 50 m above ground level which would not sufficient for wind power generation. However, the established Singapore wind map is expected to be applied for wind environment assessment and urban planning purpose.

• Journal of Communications and Networks
• /
• 제12권5호
• /
• pp.459-465
• /
• 2010

A new blind equalization algorithm that is based on maximizing the probability that the constant modulus errors concentrate near zero is proposed. The cost function of the proposed algorithm is to maximize the probability that the equalizer output power is equal to the constant modulus of the transmitted symbols. Two blind information-theoretic learning (ITL) algorithms based on constant modulus error signals are also introduced: One for minimizing the Euclidean probability density function distance and the other for minimizing the constant modulus error entropy. The relations between the algorithms and their characteristics are investigated, and their performance is compared and analyzed through simulations in multi-path channel environments. The proposed algorithm has a lower computational complexity and a faster convergence speed than the other ITL algorithms that are based on a constant modulus error. The error samples of the proposed blind algorithm exhibit more concentrated density functions and superior error rate performance in severe multi-path channel environments when compared with the other algorithms.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 춘계학술대회논문집
• /
• pp.426-430
• /
• 2005

The fiber-optic interferometer which is a powerful application for nondestructive measurement techniques has many advantages such as capability of making portable system, easy optical arrangement, low optical loss. In spite of these advantages, this system has an environmental sensitivity of thermal drifts and vibrations. Against environmental perturbations and nonlinear characteristic of phase modulator, the accurate and fast ${\pi}/2$ phase stepping has been achieved by using zero-crossing detection. CCD camera trigger signal is generated at the 4 zero-crossing points. Our System has achieved up to 100 Hz of image capture speed and 0.6 mrad of accuracy of phase stepping, accuracy.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1999년도 전력전자학술대회 논문집
• /
• pp.663-666
• /
• 1999

This paper describes a three-phase converter with high power factor using a scheme of discontinuous current mode(DCM). The proposed system can replace the conventional diode bridge with step-up chopper which is used as a converter for adjustable speed drive. In this system, the current of reactor is zero at turn-on instance because of operation in DCM, while the switch turns off at the instance of maximum current. A soft-switching scheme with lossless snubber was proposed. Therefore, a zero-voltage switching at turn off can be achived by lossless snubber and zero-current switching at turn on can be obtained by operating under DCM. A theoretical analysis and computer simulations with PSpice were done to verify the operation of the proposed system. Also a prototype of hardware system was built and tested for verifying the feasibility of proposed system.

• 제어로봇시스템학회논문지
• /
• 제21권9호
• /
• pp.869-874
• /
• 2015

We developed an LSDC (Load Shift and Load Distribution Control) technology in order to improve coil quality and productivity by reducing tension fluctuation especially for the tail of the strip in the down coiler in hot strip mills. To adapt the new controller, the torque and speed distribution between the zero pinch roll, pinch roll, and mandrel are needed. The proposed controller is a combination of an LSC to share the tension between the mill stand and the mandrel, and an LDC to shift the torque load from the zero pinch roll to the pinch roll. From the simulation, the proposed controller is verified under the torque disturbance. Using a field test, the torque deviation decreased by nearly 50% through utilization of the LSDC control.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2018년도 전력전자학술대회
• /
• pp.416-417
• /
• 2018

Brushless DC(BLDC) 모터는 브러시가 없어 고속 회전에 유리하기 때문에 핸드피스 모터에 많이 적용하는 추세이다. 핸드피스 모터는 부피가 작을수록 유리하여 홀 센서를 장착하지 않은 경우가 많기 때문에 센서리스 제어를 하여야 한다. BLDC 모터의 상 역 기전력 zero crossing 감지 방법을 이용한 센서리스 제어를 할 시 40,000rpm에 달하는 고속 회전에서 상 전압 floating 구간이 $250{\mu}s$밖에 안되기 때문에 샘플링이 부족하고 스위칭 노이즈도 강해 zero crossing에 대한 감지가 어려울 수 있다. 이 논문에서는 역 기전력에 대한 비선형 필터인 majority function을 응용함으로써 모터 상 역기전력의 zero crossing을 감지해내고 고속 BLDC 모터 센서리스 제어를 하는 방법을 소개한다.

• 한국산학기술학회논문지
• /
• 제7권6호
• /
• pp.1206-1213
• /
• 2006

자기 전파하는 웜들의 속도가 사람이 대응하는 속도 보다 매우 빠르기 때문에 zero-day 웜들을 봉쇄하기 위해서는 웜 시그니쳐의 빠른 검출과 자동생성이 필수적이다. 본 논문에서는 웜 공격에 대응 할 수 있는 시그니쳐 자동생성 방법을 제안하고, 제안한 방법의 프로토타입을 구현하여 DHT 기반 네트워크에 적용하여 웜 시그니쳐를 생성함으로써 제안한 방법의 유효성을 보이도록 한다.

• Journal of Biosystems Engineering
• /
• 제21권4호
• /
• pp.429-435
• /
• 1996

A wind tunnel consisting of two air flow conditioners with polycarbonate pipes, a plant growth room, a suction fan and fan controller, and fluorescent lamps, was designed to investigate the interactions between the growth of plug seedlings under artificial light and their Physical environments. Light transmissivities in the plant growth room based on the photosynthetic photon flux density and photosynthetically active radiation was appeared to be 96.3% and 96.8%, respectively. Measurement showed a uniformity in the vertical profiles of air current speed at the middle and rear regions of plug trays in wind tunnel. This result indicated that the development of a wind tunnel based on the design criteria of the American Society of Mechanical Engineers was adequate. Air current speed inside the plug stand was significantly decreased due to the resistance by the leaves of plug seedlings and boundary layer developed over and below the plug stand. Driving force to facilitate the diffusion of gas inside the plug stand might be regarded as extremely low. Aerodynamic characteristics above the plug stand under artificial light were investigated. As the air current speed increased, zero plane displacement decreased but roughness length and frictional velocity increased. Zero plane displacement linearly increased with the average height of plug seedlings. The wind tunnel developed in this study would be useful to investigate the effects of air current speed on the microclimate over and inside the plug stand and to collect basic data for a large-scale plug production under artificial light in a semi-closed ecosystem.

• 한국자동차공학회논문집
• /
• 제6권2호
• /
• pp.1-11
• /
• 1998

The 4WS system is usually developed to improve the maneuverability at low speed and the straight line stability at high speed, but it is found to have the severe understeer characteristics at high speed. Therefore a 4WS vehicle requires to turn the steering wheel much more than a 2WS vehicle at high speeds even a driver goes through the same curved road. In this study, to enhance the cornering performance of the 4WS vehicle at high speed, a DYC 4WS system is proposed based on the nonlinear 4WS system and direct yaw moment control system. Especially the proposed DYC 4WS system is able to realize a zero side slip angle for vehicles and a cornering performance similar to the 2WS vehicle at high speed.