• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.1
• /
• pp.54-61
• /
• 2000

Conventionally, ZVS FB DC/DC converter was controlled by monolithic IC UC3879, which includes the functions of oscillator, error amplifier and phase-shift circuit. Also, microprocessor and DSP have been widely used for the remote control and for the immediate waveform control in ZVS FB DC/DC converter. However the conventional microprocessor controller is complex and difficult to control because the controller consists of analog and digital parts. In the case of the control of FB DC/DC converter, the output is required of driving a direct signal to the switch drive circuits by the digital controller. So, this paper presents the method and realization of designing the digital-to-phase shift PWM circuit controlled by DSP (TMX320C32) in a 2,500A, 40㎾ ZVS FB DC/DC converter.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.461-463
• /
• 1996

A FB-ZVS(Full Bridge Zero Voltage Switching) PWM DC/DC converter for electric vehicles is analyzed in this paper. The converter considered is a step-down DC/DC converter with the ratings of 3l2/I3.5V and 1.35kW. The steady state analysis of this converter is divided into six operating modes. Digital simulations using PSPICE are carried out to verify the steady-state analysis.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2023-2027
• /
• 1997

This paper presents the dynamic analysis and control-loop design of a zero-voltage-switched full bridge (ZVS-FB) PWM dc/dc converter. Based on the small-signal analysis results, the control-loop is designed using a simple two-pole one-zero compensation circuit. Design results are verified by both computer simulations and experimental data obtained from a 2kW prototype converter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.3 no.3
• /
• pp.231-239
• /
• 1998

This paper presents the dynamic analysis and control loop design of a zero voltage switching full bridge (ZVS-FB) PWM DC/DC converter. The small-signal model is derived incorporating the effects of phase shift control and the utilization of transformer leakage inductance and power FET junction capacitance to achieve zero voltage resonant switching. These effects are modeled by introducing additional feedforward and feedback terms for duty cycle modulation. Based on the results of the small-signal analysis, the control loop is designed using a simple two-pole one-zero compensation circuit. To show the validity of the design procedures, the small signal analysis of the closed loop system is carried out and the potential of the zero voltage switching and the superiority of the dynamic characteristics are verified through the experiment with a 2 kW prototype converter.

• Proceedings of the KWS Conference
• /
• 2000.04a
• /
• pp.99-102
• /
• 2000

Conventionally, ZVS FB DC/DC converter was controlled by monolithic IC UC3879, which includes the functions of oscillator, error amplifier and phase-shift circuit. Also, microprocessor and DSP have been widely used for the remote control and for the immediate waveform control in ZVS FB DC/DC converter. However the conventional microprocessor controller is complex and difficult to control because the controller consists of analog and digital parts. In the case of the control of FB DC/DC converter, the output is required of driving a direct signal to the switch drive circuits by the digital controller. So, this paper presents the method and realization of designing the digital-to-phase shift PWM circuit controlled by DSP (TMX320C32) in a 2,500A, 40㎾ WS FB DC/DC converter.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.111-115
• /
• 1997

This Paper is concerned on developing DC-DC converter using ZVS-FB-PWM Converter. The converter output is 28V and regulated by phase shift control methode. MOSFET is used by the main switching device and high frequency transfomer is made for operating at 300㎑ switching frequency. When the load vary widely, converter's ZVS characteristic is expressed by experiment result.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.363-366
• /
• 1996

A FB-ZVS(Full Bridge Zero Voltage Switching) PWM DC/DC converter for electric vehicles is simulated and implemented in this paper. The converter considered is a step-down DC/DC converter with the ratings of 312/13.5V and 1.35kW. The steady state operation of this converter is divided into six operating modes in case of continuous current mode and eight operating modes in case of discontinuous current mode. Digital simulations using PSpice are carried out to verify the steady-state analysis. A prototype converter was built in the laboratory. MOSFETs were used for swithching devices and fast recovery diodes to reduce the charge storage problem of a pn-junction.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.392-394
• /
• 1996

This paper is to describe how to apply the Phase-shifted Full Bridge 100kHz high frequency soft-switching PWM method to 48[V], 200[A] DC/DC converter. The soft-switching is achieved from light load to full load by using phase-shifted zero voltage switching method with additional capacitors besides the MOSPET's of the right leg even though the leakage inductance of high frequency transformer is designed small. This method can reduce the switching tosses, EMI problems, and increase the effective duty. Also, this paper includes the simulation, analysis, and experiment results of the DC/DC converter unit.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.618-621
• /
• 1999

With the advent of the high-speed microprocessor and DSP, the possibility of executing a control strategy in digital domain has become a reality. By the use of the DSP and microprocessor controller, many high power drive system may be enhanced resulting in the improved robustness to EMI, the ability to communicate the operating conditions and the ease of adjusting the control parameters. But, the digital controller using DSP or microprocessor is not applied in the high frequency switching power supplies, especially full bridge DC/DC converter. So, this paper presents the method and realization of designing a digital-to-phase shift PWM circuit for full digital controlled full bridge DC/DC converter with zero voltage switching. The operating principles, simulation and experimental results will be presented.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.365-367
• /
• 1995

This paper is concerned on developing low-voltage high-current DC-DC converter using FB-ZVS PWM Converter. The converter output is 28V, 100A and regulated by phase-shift control method. IGBT is used by the main switching device and high frequency transformer is made for operating at 30kHz switching frequency. When the load vary widely, converter's ZVS characteristic is expressed by experiment result.