• 한국세라믹학회지
• /
• 제50권4호
• /
• pp.257-262
• /
• 2013

A biomimetic approach was applied for the chemical deposition of calcium phosphate (CaP) coatings on 3 mole% yttrium-stabilized zirconia [3YSZ] powders. The solid-state reaction of 3YSZ powders with the addition of CaP was investigated for the development of biodegradable zirconia ceramics. The solid-state interaction between the 3YSZ matrix powders and the CaP additives differed from the behavior of commercial zirconia matrix powders. The 3YSZ powders were chemically reacted with precursors for the CaP formation. 3YSZ powders were mixed in an aqueous solution of Ca-P precursors and the CaP was precipitated on the surface of the 3YSZ matrix powders. The CaP-doped YSZ powders were calcined at $1100^{\circ}C$ and shaped powder blocks were then fired at $1600^{\circ}C$ for 2 h. The CaP phase formation was investigated using FE-SEM and XRD analysis.

• 한국세라믹학회지
• /
• 제34권11호
• /
• pp.1113-1120
• /
• 1997

The 2, 4, 6 and 8mol% Y2O3 doped-ZrO2 powders (20 kinds) with the addedtion of Al2O3 upto 8wt% were prepared by coprecipitation method using the zirconium oxyacetate, yttrium chloride and aluminum nitrate as starting materials. The coprecipitated powders were characterized by XRD, TG-DTA, FT-IR and SEM. The sintering properties of zirconia-alumina composites prepared by 2YSZ and 8YSZ powders containing various Al2O3 contents were also investigated. With increasing the yttria stabilizer contents, the amount of exothermic heat for zirconia crystallization decreased. And it was confirmed that the crystallizing temperature of coprecipitated zirconia powders increased and the crystallization process occurred in a wide temperature range, as Al2O3 content increased in 8YSZ.

• Journal of Korean Vacuum Science & Technology
• /
• 제2권1호
• /
• pp.43-48
• /
• 1998

The effect of mcirostructure on the electrical properties of yttria stabilized zirconia (YSZ) was analyzed by modeling layer arrangements and mixed phase structure. The YSZ thin films were deposited by RF magnetron sputtering using 30mol% YSZ and 8 mol% YSZ targets with yttrium pellets on porous alumina substrates. The structure, composition and electricla properties of the YSZ films were investigated as functions of sputtering conditons and layer arrangements by XRD, TEM, XPS and acimpedance spectroscopy. The results showed that the triple palyered YSZ films had highermicrohardness, lower compressive stress state and higher ionic conductivity by one order than single and double layered YSZ films. However, sputtered YSZ films have low conductivity compared to YSZ pellets or doctor bladed YSZ thin plates. These results were probably due to the influence of insulating alumina substrates, impractical for most stacking geometries and inductance induced by relatively long platinum, lead wire on YSZ conductivity.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.1001-1002
• /
• 2013

• 한국세라믹학회지
• /
• 제33권3호
• /
• pp.355-361
• /
• 1996

Yttria stabilized zirconia (YSZ) thin films were prepared by the electrochemical vapor deposition (EVD) method on the porous Al2O3 substrates. Y2O3 mol% of thin film was linearly increased with yttrium mole fraction of vapor phase. As yttrium mole fraction(Zyc13=0.18) increased dense and faceted thin films were enhanced. However as the yttrium mole fraction (Zyc13=0.04) decreased porous thin films with monoclinnic phase prevailed. With increasing pressure difference of substrate sides penetration depth decreased porosity and amount of monoclinic phase in the films increased.

• 한국표면공학회지
• /
• 제30권3호
• /
• pp.183-190
• /
• 1997

Fabrication and crystallization characteristics of yttria($T_2O_3$) stabilized zirconia(YSZ) thin film by sol-gel process were studied. YSZ sol was synthesized with zirconium n-propoxide($Zr(OC_3H_7)_4)$) and yttrium nitrate pentahydrate ($Y(NO_3)_3.5H_2O$). YSZ film was prepared by depositing the polymeric sol on porous $Al_2O_3$ substrate by spin-coating, and the film characteristics were investigated by FRIR, TG-DTA, XRD, DSC, optical microscopy and SEM. The film topology was uniform and cracks were not found. It was found that the annealing temperature and the concentration of stabilizer affect the crystallization of YSZ film. The YSZ film began to crystallize from amorphous to tetragonal phase at 40$0^{\circ}C$, and it was not converted to cubic structure until $1100^{\circ}C$. It seemed that the grains were formed over $700^{\circ}C$and the average grain size was obtained about 0.2$\mu\textrm{m}$.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 추계학술대회 논문집
• /
• pp.591-592
• /
• 2012

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.191-192
• /
• 2008

• 한국세라믹학회지
• /
• 제51권5호
• /
• pp.466-471
• /
• 2014

Hydrous zirconia particles were prepared from $ZrOCl_2$ aqueous solution using an electro-dialysis [ED] process. For the preparation of $(Zr,Y)(OH)_4$ precipitates, 3 mol% $YCl_3$ was added into $ZrOCl_2$ aqueous solution. During the hydrolysis of 0.5 mol/L $(Zr,Y)OCl_2$ solution at $90^{\circ}C$ a slurry solution was obtained. The ED process was used for the removal of chlorine from the slurry solution. Two kinds of slurry solution were sampled at the beginning and end of the ED process. The morphology of hydrous zirconia particles in the solution was observed using an inverted optical microscope and an FE-SEM. The hydrous zirconia particles were nano-crystalline, and easily coagulated with drying. Yttrium stabilized zirconia [YSZ] powder could be obtained by the calcination of $(Zr,Y)(OH)_4$ precipitates prepared from a $(Zr,Y)OCl_2$ solution by the ED process. The coagulated dry powders were shaped and sintered at $1500^{\circ}C$ for 2 h. The sintered body showed a dense microstructure with uniform grain morphology.

• 한국세라믹학회지
• /
• 제55권6호
• /
• pp.576-580
• /
• 2018

In this study, a small amount of CoO was added to commercial Gd-doped $CeO_2$ (GDC) powder. The CoO addition greatly enhanced sinterability at low temperatures, i.e., more than 98% of relative density was achieved at $1,000^{\circ}C$. When GDC/8YSZ (8 mol% yttrium stabilized zirconia) bilayers were sintered, Co-doped GDC showed excellent adhesion to the YSZ electrolyte. Transmission electron microscope (TEM) analysis showed that there were no traces of liquid films at the grain boundaries of GDC, whereas liquid films were observed in the Co-doped GDC sample. Because liquid films facilitate particle rearrangement and migration during sintering, mechanical stresses at the interface of a bilayer, which are developed based on different densification rates between the layers, might be reduced. In spite of $Co^{2+}$ doping in GDC, the electrical conductivity was not significantly changed, relative to GDC.