• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.09a
• /
• pp.219-224
• /
• 2009

In this study, the characteristics of pullout behavior of Pressurized light-weight steel Anchor was investigated through centrifuge model tests considering pull-out angle $0^{\circ}$ with changing undrained shearstrength(0~1, 2~4, 5~7kPa) of clay. According to the results of tests, the yield pullout load of clay ground was gradually increased up to 30% as undrained shear strength was increased. Therefore, it was known that the yield pullout load was affected by increasing the undrained shear strength, in addition, the pattern of behavior was not changed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.12
• /
• pp.2285-2290
• /
• 2008

Even though efficiency of coal-fired power plant is proportional to operating temperature, increasement of operating temperature is limited by a technological level of each power plant component. It is an alternative plan to increase operating pressure up to ultra super critical point for efficiency enhancement. It is difficult to control process of power plant in ultra super critical point because that point has highly nonlinear characteristics. In this paper, new control logic, Unit Response Optimizer Controller(URO Controller) which is based on Fuzzy logic and Model Predictive Controller, is introduced for better performance. Then its performance is tested and analyzed with design guideline.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.12
• /
• pp.2234-2237
• /
• 2008

Approximate equations for cylindrical breakdown voltages of planar pn junctions are proposed and verified. The equations show good agreement with the Baliga's results for $r_{j}/Wpp{\leqq}0.3$ and with numerical results for $r_{j}/Wpp{\geqq}0.3$ within 1% error. Sensitivity of the breakdown voltage with respect to the doping concentrations is successfully derived using the approximate equations. The sensitivity formula can be utilized in the area of tolerance design of power semiconductor devices.

• IE interfaces
• /
• v.25 no.2
• /
• pp.216-228
• /
• 2012

BIM-based 4D simulation makes people easily understand complex construction process using 3D graphics model and helps them review and identify the construction schedule in each phase of the construction process. Moreover, 4D simulation can be used as reference data to determine the validity of the process in the design phase and will be utilized as a measure for checking the construction process. Therefore 4D simulation of construction improves efficiency of project management. However, current commercial applications available for 4D simulation do not provide sufficient functions for connection of 3D models and process information. In this paper, we propose an automated generation method through the definition of the process based on a work method template and developed the template based schedule generation system (TSGS).

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.366-369
• /
• 2005

The smelting system using induction heating technology has many advantages over conventional fossil fuel regarding energy efficiency, environmental aspect and so on. This paper introduces the principal and technical trends of Induction heating technology, and describes recently developed 2500kW induction smelting inverter, The developed inverter is a series resonant type using high speed Thyristor (SCR) and employs state-of-art digital controller using DSP.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.156-158
• /
• 2005

The computation of design parameters and the electromagnetic analysis of 0.5 Mw- class Induction furnace with 3-dimensional modeling are Introduced by using FEM techniques, And model of flux distribution and eddy current distribution induced in induction furnace are analyzed and presented. It is more necessary that for melting industry depending on metal material field, the design technique of induction furnace is quite urgent at exchanging introduction of technology between metal material and electrical energy conversion by power electronics field.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.370-373
• /
• 2009

X-ray lithography was employed to fabricate ITO-less high resolution sustain electrodes for plasma display panel (PDP). A polyimide film based X-ray mask and Xray sensitive Ag electrode paste were fabricated to check their effect on the patterning of Ag electrodes with less than 30 ${\mu}m$ in width. The X-ray lithographic method was found to be useful for the high resolution sustain electrode patterns due to the high penetration power and low scattering property of X-ray source.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.316-319
• /
• 2007

In this paper, high precision molding process was developed using a soft mold to fabricate fine closed-types of the barrier ribs for PDP. A green sheet was employed to fabricate the barrier ribs in this process. The soft mold with good demolding characteristics was replicated from a master mold. An optimal forming load which would not fracture the soft mold was also determined. The barrier ribs of rectangular type with upper width of $30\;{\mu}m$ would be fabricated by this process.

• Proceedings of the KIPE Conference
• /
• 2019.11a
• /
• pp.154-155
• /
• 2019

항만 내 대표적인 하역장비로는 RTG와 YT가 있으며 주로 디젤엔진을 사용하고 있다. 항만의 그린화 및 무인화를 위해 물류장비의 전기동력 전환의 필요성 증가 및 전기동력 충전을 위한 유선 또는 무선 충전기술 등이 고려 되고 있다. 본 논문에서는 항만에서 운영되는 전기식 YT의 운영 패턴을 고려해 수시로 충전이 가능한 무선전력 전송시스템을 제안하였다. 또한 제안한 시스템의 검증을 위해 실험용 시스템을 구축하여 전력전송 용량 및 효율실험 결과를 통하여 타당성을 확인하였다.

• Proceedings of the KIPE Conference
• /
• 2019.11a
• /
• pp.156-157
• /
• 2019

경량전철과 같은 대용량 전력 시스템에 무선전력전송 기술을 적용할 때 전력변환장치의 병렬 운전은 필수적이다. 병렬 연결된 전력변환장치의 경우 출력이 공통으로 연결되어 전력을 공급하게 되는데, 이 때 집전 컨버터의 부하균등제어는 각각의 집전 컨버터의 부하 불균형을 막아줌으로써 집전 컨버터의 수명과 효율이 감소하는 것을 막아준다. 본 논문에서는 부하균등제어방법을 적용한 무선 경량전철 시스템을 통해 기존에 제안된 제어기법을 적용하여 검증하였다. 실증시험의 경우 경산에 위치한 한국철도기술연구원 경량전철시험선의 시험용 경량전철을 두 개의 역사를 반복하여 셔틀 운행하여 최대 400kW의 전력을 두 개의 집전 장치가 전력을 균등하게 공급하는 것을 확인 및 분석하여 논문의 타당성을 검증하였다.