• 한국분말재료학회지
• /
• 제10권3호
• /
• pp.190-194
• /
• 2003

Thin Ag films deposited onto $SiO_2/Si$ substrates by DC magnetron sputtering and thereafter annealed ,it temperatures 100-50$0^{\circ}C$ are investigated by scanning tunneling and atomic forte microscopy. It is shown that the film surface topography and microstructure are considerably changed as a result of annealing. To provide a quantitative estimation of the surface topography changes of Ag films the surface fractal dimension was calculated. Elasticity and hardness of the films are studied by a nanoindentation technique. The films are found to have value of elastic modulus close to that of bulk silver while their hardness and yield stress are essentially higher.

• 한국화재소방학회논문지
• /
• 제27권4호
• /
• pp.7-12
• /
• 2013

건축물에서의 화재 발생은 인명피해, 구조물 피해 등 재해적 요소를 많이 포함하고 있으며, 가연물의 증가에 따라 화재 발생빈도수와 피해 규모는 점차 증대하는 추세이다. 특히 강재로 구성되는 기둥부재와 보부재의 고온 시 내력의 급격한 감소는 구조물의 붕괴와 같은 매우 위험한 상황에 도달될 수 있으므로 화재 시 강구조 건축물의 구조 안전성 확보를 위해서는 적용 강재의 신뢰성 있는 고온 물성자료가 매우 중요하다. 따라서 본 연구에서는 강구조 건축물에서 많이 활용되는 용접구조용 강재인 SM 400강재를 대상으로 고온 시 항복강도, 탄성계수를 측정하여 내력평가에 활용할 수 있는 실험식을 제시하고, 화재 시의 온도평가와 응력 계산에 요구되는 열전도율과 열팽창계수 등의 열적 특성의 자료를 제시한다. 또한 일반 구조용 강재인 SS 400과의 고온 특성을 비교, 평가함으로써 고온에서의 내력 특성을 확인한다.

• 대한기계학회논문집A
• /
• 제22권4호
• /
• pp.905-915
• /
• 1998

Static tensile tests using adhesive-bonded single-lap joints of aluminum alloy were conducted to investigate the effect of geometric factor, overlap length, adherend thickness, adhesive thickness and material composition of adherend/adhesive on the strength of adhesive joint. The average applied shear stress at joint fracture decreased with increasing lap length. However increasing the adherend thickness resulted in a higher joint strength. Higher yield strength of adherend and lower elastic modulus of adhesive is advantageous to the adhesive joint. Newly proposed modified joint factor could be well evaluated the influence of lap length, adherend thickness and adhesive thickness on the bond strength for adhesive joints.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.13-19
• /
• 2008

A Wire-woven Bulk Kagome (WBK) is the new truss type cellular metal fabricated by assembling the helical wires in six directions. The WBK seems to be promising with respect to morphology, fabrication cost, and raw materials. In this paper, first, the geometric and material properties are defined as the main design parameters of the WBK considering the fact that the failure of WBK is caused by buckling of truss elements. Taguchi approach was used as statistical design of experiment(DOE) technique for optimizing the design parameters in terms of maximizing the compressive strength. Normalized specific strength is constant regardless of slenderness ratio even if material properties changed, while it increases gradually as the strainhardening coefficient decreases. Compressive strength of WBK dominantly depends on the slenderness ratio rather than one of the wire diameter, the strut length. Specifically the failure of WBK under compression by elastic buckling of struts mainly depended on the slenderness ratio and elastic modulus. However the failure of WBK by plastic failed marginally depended on the slenderness ratio, yield stress, hardening and filler metal area.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1-6
• /
• 2008

Due to the self-similarity of Berkovich and conical indenters, different materials may show the same loaddepth curve for single indentation. In this study, we first compare the load-depth characteristics of conical and Berkovich indenters via finite element method. We also analyze the variation of load-depth curves with angle of Berkovich indenter, indentation parameters, and material properties. With numerical regressions of obtained data, we then propose dual-Berkovich indentation formulae for material property evaluation. The proposed approach provides the values of elastic modulus, yield strength and strain-hardening exponent and corresponding stress-strain curve with an average error of less than 3%. The method is valid for any elastic indenters made of tungsten carbide and diamond for instance.

• Structural Engineering and Mechanics
• /
• 제58권4호
• /
• pp.641-659
• /
• 2016

This paper deals with the pure bending of incompressible elastic perfectly plastic two-layer sheets under plane strain conditions at large strains. Each layer is classified by its yield stress, shear modulus of elasticity and its initial percentage thickness in relation to the whole sheet. The solution found is semi-analytic. In particular, a numerical technique is only necessary to solve transcendental equations. The general solution is cumbersome because different analytic expressions for the radial and circumferential stresses should be adopted in different regions of the whole sheet. In particular, there are several alternative ways a plastic region (or plastic regions) can propagate. However, for any given set of material and process parameters the solution to the problem consists of a sequence of rather simple analytic expressions connected by transcendental equations. The general solution is illustrated by a simple example.

• 한국재료학회지
• /
• 제14권6호
• /
• pp.436-442
• /
• 2004

Elastic and plastic deformation behaviors of the high purity aluminum and the silica glass were studied using nanoindentation and finite element analysis(FEA) techniques. Berkovich- and cone-type indenters were used for the nanoindentation test. Deformation behaviors and nanoindent profiles of elastic, elastic-plastic or plastic materials were clearly visualized by FEA simulation. Effects of the penetration depth and strain hardening on the deformation behavior were examined. Pile-up and sink-in behaviors were studied by using FEA technique. Degree of pile-up or sink-in was found to be a function of the ratio of elastic modulus to yield strength of materials. FEA was found to be an effective method to study deformation behaviors of materials under nanoindentation, especially in the case when pile-up or sink-in phenomena occurred.

• 한국철도학회논문집
• /
• 제11권1호
• /
• pp.61-68
• /
• 2008

교통하중이 작용하는 노반의 응력-변형율 간의 상관성의 특징을 나타내기 위하여 회복탄성계수가 사용되어왔다. 최근 도로의 경우 노반의 설계에 있어 AASHTO에서 제안된 역학적-경험적 설계가이드에 따라 회복탄성계소의 사용이 더욱 권장되는 실정이다. 이에 비해 국내 철도의 노반설계에 있어서는 정적실험 결과인 $K_{30}$이나 변형계수를 사용하고 있는 실정이다. 따라서 철도노반의 설계에 있어 회복탄성계수의 적용 가능성에 대한 평가가 이루어져야 할 것이다. 본 연구에서는 14종의 점성토 흙에 대하여 회복 및 영구변형 특성에 대한 평가를 위하여 기본 물성실험, 일축압축실험 그리고 회복탄성계수 실험을 수행하였다. 또한 일축압축 실험결과와 접선탄성계수, 일축압축강도, 파괴시 변형율 첨두 강도에서의 할선탄성계수와 항복변형율을 바탕으로 회복탄성계수 추정을 위한 예측모델이 제안되었다. 본 연구에서 제안된 예측모델은 실측결과와의 비교시 만족할 만한 값을 보이는 것으로 확인되었다. 다만 회복탄성계수 실험시 발생하는 영구변형에 대해서는 현재 고려하고 있지 않다.

• Geomechanics and Engineering
• /
• 제6권2호
• /
• pp.173-194
• /
• 2014

Laboratory and field data showed that deep mixed (DM) columns accelerated the rate of consolidation of the soft foundations. Most analyses of consolidation of DM column-improved foundations so far have been based on the elastic theory. In reality, the DM columns may yield due to the stress concentration from the soft soil and its limited strength. The influence of column yielding on the degree of consolidation of the soft foundation improved by DM columns has not been well investigated. A three-dimensional mechanically and hydraulically-coupled numerical method was adopted in this study to investigate the degree of consolidation of the DM column foundation considering column yielding. A unit cell model was used, in which the soil was modeled as a linearly elastic material. For a comparison purpose, the DM column was modeled as an elastic or elastic-plastic material. This study examined the aspects of stress transfer, settlement, and degree of consolidation of the foundations without or with the consideration of the yielding of the DM column. A parametric study was conducted to investigate the influence of the column yielding on the stress concentration ratio, settlement, and average degree of consolidation of the DM column foundation. The stress concentration ratio increased and then decreased to reach a constant value with the increase of the column modulus and time. A simplified method was proposed to calculate the maximum stress concentration ratios under undrained and drained conditions considering the column yielding. The simplified method based on a composite foundation concept could conservatively estimate the consolidation settlement. An increase of the column modulus, area replacement ratio, and/or column permeability increased the rate of consolidation.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.334-337
• /
• 2007

Austenitic stainless steel is used as high temperature components such as gas turbine blade and disk because of its good thermal resistance. In the present investigation, tensile and low cycle fatigue(LCF) behavior of stainless steel for turbine disks was studied at wide temperature range $20^{\circ}C\;{\sim}\;750^{\circ}C$. In the tensile tests, it was shown that elastic modulus, yield strength, ultimate tensile strength decreased when temperature increased. The effect on fatigue failure of the parameters such as plastic strain amplitude, stress amplitude and plastic strain energy density was also investigated. Coffin-Manson and Morrow models were used to adjust experimental data and predict the fatigue life behavior at different mean strain values during cyclic loading of high temperature components.