• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.729-734
• /
• 2003

This paper reports the characteristics of the three dimensional turbulent flow in the rectangular-sectioned 180 degree bends by Hot-wire anemometer. Grande and Kool proposed a cooling law for the measurements of the flow through the narrow passage. The authors noticed that the calibration coefficients of original method are not constant and fairly sensitive to the flow approaching angle. Measured voltages are converted to three velocity and six Reynolds stress components using the modified method in which the coefficients are treated as a function of approaching angle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.5
• /
• pp.186-193
• /
• 1999

In this paper, a full vehicle model is developed to analyze toe and camber changes due to rack height variation and compliance. The AutoDyn7 program developed in G7 project is used for the computer simulation. Steady state cornering test was done to find the understeer gradient. Imposing a pulse steer input, Frequency Response Function(FRF) of yaw rate and lateral accelerations were evaluated. To verify the stability, the rhombus using four parameters is employed. Steer characteristics were evaluated by changing the rack height and the bushing lateral stiffiness. which installed between the low control arm and the chassis.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.6
• /
• pp.470-476
• /
• 2016

This paper proposes a practical algorithm for the reduction of measurement errors due to drift in a micro-electromechanical system (MEMS) gyros that are used for a mobile robot. Any drift in a MEMS gyro will cause an unbounded growth of errors in the estimation of heading, which makes it nearly useless in applications that require high accuracy over a long operating time. In proposed method, maneuvers of a cleaning robot are observed through encoders' measurement process and a decision to correct bias drift will be made if necessary. The method used in this paper is called the "heading estimation filter". To evaluate the accuracy of the proposed method, a comparison was made between the estimation of the heading of the cleaning robot and one from a motion capture system.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2001.05a
• /
• pp.222-227
• /
• 2001

The time simulation of slow drift motions of moored FPSO in waves is presented. The equation of motion based on Cummin's theory of impulse responses are employed, and are consisted of horizonal plane -surge, sway and yaw. The added mass coefficients, wave damping coefficients, first order wave exciting forces and the second order wave drift forces involved in the equations are obtained from a three-dimensional panel method in the frequency domain. The mooring lines are modeled quasistatically as catenary for chains and touchdown. As for numerical example, time domain analyses are carried out for a box-type FPSO in long crest irregular wave condition.

• Journal of Communications and Networks
• /
• v.15 no.6
• /
• pp.606-613
• /
• 2013

This paper proposes a complete solution of a contention-based medium access control in wireless local networks to provide station level quality of service guarantees in both downstream and upstream directions. The solution, based on the mature distributed coordination function protocol, includes a new fixed contention window backoff scheme, a tuning procedure to derive the optimal parameters, a super mode to mitigate the downstream bottleneck at the access point, and a simple admission control algorithm. The proposed system guarantees that the probability of the delay bound violation is below a predefined threshold. In addition, high channel utilization can be achieved at the same time. The numerical results show that the system has advantages over the traditional binary exponential backoff scheme, including efficiency and easy configuration.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.72-77
• /
• 2008

The function of the Reaction Control System include roll, pitch and yaw control of the launch vehicles and fine control maneuvers and precision upper stage orientation before separation of one or more payload. This paper describes the overview of commercial launchers, current technology trend for RCS of launch vehicles, and development status of medium class thruster for RCS.

• Advances in aircraft and spacecraft science
• /
• v.9 no.1
• /
• pp.1-15
• /
• 2022

This paper presents calibration of flush air data sensing systems during ascent period of a satellite launch vehicle. Aerodynamic results are numerically computed by solving three-dimensional time dependent compressible Euler equations over a payload shroud of a satellite launch vehicle. The flush air data system consists of four pressure ports flushed on a blunt-cone section of the payload shroud and connected to on board differential pressure transducers. The inverse algorithm uses calibration charts which are based on computed and measured data. A controlled random search method coupled with neural network technique is employed to estimate pitch and yaw angles from measured transient differential pressure history. The algorithm predicts the flow direction stepwise with the function of flight Mach numbers and can be termed as an online method. Flow direction of the launch vehicle is compared with the reconstructed trajectory data. The estimated values of the flow direction are in good agreement with them.

• International Journal of Railway
• /
• v.3 no.3
• /
• pp.95-105
• /
• 2010

In this paper, a procedure is proposed to optimize bogie suspension parameters in view of minimizing wheel wear produced by curve negotiation, though meeting stability requirements. The problem is dealt with in the form of a constrained minimization problem, in which wheel wear evaluated over a given service scenario is introduced as the cost function to be minimized, and the requirements on vehicle stability are formulated in terms of constraints. The procedure is applied to the case of a non-powered passenger car for high-speed service, and the results obtained are discussed. It is shown that long wheelbase bogie may provide better overall performances than bogies having comparatively short wheelbase. Furthermore, a sensitivity analysis is performed, to define the effect on the optimization results of improving the performances of the yaw dampers in the bogie and of using a different wheel profile.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.2
• /
• pp.595-608
• /
• 2013

This paper is proposed the computation method of moored ship motion considering harbor resonance, and estimated that the harbor resonance have an effect on moored ship motion. The computation of harbor resonance was used CGWAVE model and the computation of moored sip motion was used the Green function method expressed by three dimensions. This method was verified with the field observation data of moored ship motion, and the application of actual harbor was investigated with wave field data and down time record data in Pohang New Harbor. The resonance periods in Pohang New Harbor that obtained from wave field data were 80, 33, 23, 8 minute, which are the long waves, and 42, 54, 60 second, which are the infra-gravity waves inside harbor slip. The simulated results of harbor resonance were corresponded with the wave field data. This study was investigated on 5,000 ton, 10,000 ton and 30,000 ton ship sized in Pier 8 of Pohang New Harbor that the harbor resonance has effect on moored ship motion from simulated results of ship motion in case of included resonance and excluded resonance. In case of included resonance, the ship motion have increased by 12~400 percent when compared with results of excluded resonance. We could find that the harbor resonance have still more an effect on the surge and heave motions of a large size ship and the roll and yaw motions of a small size ship.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.5
• /
• pp.385-393
• /
• 2021

This study proposes a multi-core-based controller design for an ESC(Electronic Stability Control) system in an automotive multi-core processor. Considering the architectures of an automotive multi-core processor and an ESC system, the overall execution time has been optimized for multi-core platforms. The function module assignment, synchronization between cores, and memory assignment for core-dependent variables in automotive multi-core systems are evaluated. The ESC controller comprising five function modules is used herein. Based on the proposed design, the single-core controller is extended to multi-core controllers. Using multi-core optimization methods, such as function module assignment, semaphore, interrupt awakening, and variable assignment over cores, the ESC system is redesigned to a multi-core controller. Experimental results reveal that the execution time for the multi-core processor is reduced by 59.7% compared with that for the single-core processor.